3-858-580-12(1) MD Multi-Track Recorder Operating Instructions EN Mode d’emploi F Bedienungsanleitung D T MDM-X4 © 1996 by Sony Corporation
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. INFORMATION CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
On repacking Do not throw away the carton and the packing material. This makes an ideal container when transporting the unit. When shipping the unit, repack it as it was packed at the factory. On operation • If the multi track recorder is brought directly from a cold to a warm location , or is placed in a very damp room, moisture may condense on the lens inside the MD deck. Should this occur, the system will not operate properly.
Overview of MDM-X4 Standard Recording Procedures The MDM-X4 is an integrated multichannel recorder/ mixer that can record up to 4 tracks using MD-DATA discs. In addition to 4 track recording and playback, this unit can also perform a variety of editing operations. 1 Connect instruments, microphones, effectors, (etc.) and prepare for recording. See “Connections and Signal Flow” (page 13) for details.
Overview of MDM-X4 µ 6 You decide you want to change the structure of the song. The edit functions let you add (or remove) an extra chorus or repeat the introduction in the middle of the song (etc.) without having to rerecord. See “Changing the Construction of a Song (Section Edit)” (page 38) for details. µ 7 Dub the tracks onto an external MD or DAT deck while using the mixer to adjust the balance. See “Mixdown” (page 57) for details.
Names and Functions of Parts The Mixer Also refer to the “Block Diagram” on page 64. The Channel 1~4 Section The functions described are the same for each channel (1~4). 2 INPUT selector keys Allow you to select either LINE/MIC (sound from the INPUT CH jacks) or TRACK 1~4 (sound from the recorder) for input to mixer channels 1~4. LINE/MIC : Use to input external sounds from an instrument or microphone (etc.). TRACK 1~4 : Use to input sounds played back from the recorder.
Names and Functions of Parts 8 PAN knobs Adjust the sound balance of the stereo or group bus. Turn towards␣ “L” to move the sounds toward group bus 1 or 3 and the “L” side of the stereo bus. Turn towards “R” to move the sounds toward group bus 2 or 4 and the “R” side of the stereo bus. 9 Faders 1~4 Adjust the volume of each channel. Channel 5,6 and MASTER 3 LOW knob Adjusts the bass of the sound input to the INPUT 5/6 jacks at the top of the unit. Provides a shelving type equalization.
Names and Functions of Parts 9 TRACK 1~4 knobs Use to adjust the overall sound balance when monitoring playback from the recorder (CUE monitor) by turning the knob for each track as desired. When using the CUE monitor function, be sure to press down the monitor track setting CUE key (0 below). The Recorder Control Panel 0 Monitor Track Setting keys Select the sound to be monitored. 1–2 : Press down to monitor the sound from group bus 1 and 2. 3–4 : Press down to monitor the sound from group bus 3 and 4.
Names and Functions of Parts 3 OUT key Sets the out point (edit end point). 4 IN/DEST key Sets the in point (edit start point). Press while holding down SHIFT to set the destination point (edit destination point). 5 MARK key Press to set a mark point (and the key starts blinking). Press IN, OUT, DEST, or A~H while the MARK key is blinking to set the mark point to the respective key. This unit lets you assign up to 11 mark points using IN, OUT, DEST, and A~H. 6 Locate point keys Press to recall mark points.
Names and Functions of Parts !¶ RHSL (Rehearsal) key This key has two functions: • Record rehearsal (rehearsal function) Press during record pause mode to cause the indicator to blink and set this unit to operate as if it were recording, without actually recording. This is called rehearsal mode. (Rehearsal mode can also be activated by pressing RHSL when the AUTO PUNCH key is lit.) During record rehearsal, all other operations will function as if the unit was recording.
Names and Functions of Parts 5 [EDIT] indicator Lights during edit operations (track, section, song, disc). 6 [SYSTEM] indicator Lights during system setting operations. Input and Output Jacks Top panel 7 R indicators Lights to indicate that the respective track was selected for recording using the REC SELECT keys. The track number corresponds to the group bus number. 8 Title display area Displays the song or disc title, as well as edit menu information.
Names and Functions of Parts 4 OUTPUT AUX 1/2 jacks Output sound for use as the send output. After adding an outboard effect to the sound output from these jacks, use the RETURN 1/2 (L/R) jacks to input it back to this unit. Front Panel 1 Rear Panel 2 1 2 3 1 HEADPHONES jack Connect a pair of headphones with a standard type plug. 4 56 1 MIDI THRU jack Outputs the same signal input to the MIDI IN jack. 2 MIDI OUT jack Outputs the MIDI signal.
Connections and Signal Flow Connections for Recording Connect instruments, microphones, and amp and headphones for monitoring as shown below.
Connections and Signal Flow Connecting MIDI Equipment MDM-X4 Signal Flow Diagram Connect MIDI equipment as shown in the following diagram. For details regarding connections for synchronized operation with a sequencer (etc.), see “Synchronization with MIDI Equipment” (pages 52~56). The following diagram shows the internal signal flow of this unit. 1 3 4 Sequencer (etc.) MIDI IN jack MIDI OUT jack To output the MIDI signal input to this unit’s MIDI IN jack directly to other MIDI equipment.
Monitoring Monitoring Preparations This unit enables you to monitor the following 4 types of signals as necessary. 1 Group 1, 2 : Select to monitor mixer group bus 1 and 2. The sound from group bus 1 is localized in the L (left) channel and the sound from group bus 2 is localized in the R (right) channel. When recording, select to monitor the sound being recorded. 2 Group 3, 4 : Select to monitor mixer group bus 3 and 4.
Monitoring EXAMPLE 3: Rerecording part of track 1 while monitoring the sound of tracks 3 and 4 (during punch-in/out recording, etc.) EXAMPLE 5: Monitoring the sound of the stereo bus (for mixdown, etc.) Turn to adjust level Press down Press down Turn to adjust level Turn to adjust level EXAMPLE 4: Mixing tracks 1~4 for recording onto tracks 1 and 2 (during mix write recording, etc.) You do not need to use the CUE monitor This operation uses the mixer for mixing.
Setting Up the Operating Environment System Settings You customize the operating environment by turning the MIDI synchronization and UNDO (undo last operation) functions (etc.) on or off. Pitch setting (Pitch) You can set the pitch in 0.25% increments within a range of ±8%. When you turn the pitch control on after setting the pitch , recording/playback is conducted at the selected pitch. See the “System key” in “Names and Functions of Parts” (page 9) for details on turning the pitch control on/off.
Setting Up the Operating Environment Rehearsal mode setting (RHSL) This setting lets you determine whether the volume will increase or decrease after the locate point when adjusting the position of a locate point with the rehearsal function. See page 32 for details about locate point adjustment. Â: the volume increases past the locate point.
Recording Recording Initial Recording This shows you how to record the very first track onto a blank disc. Track 1 2 3 4 6 Turn the MONITOR knob to adjust the sound to a level which can be monitored. 7 Use the fader to adjust the recording level. Play a relatively loud phrase and make adjustments by watching the level meter for the track you want to record. If necessary, you can use the TRIM knob to adjust the recording level and equalizer.
Recording Checking the Recording Overdub Recording You can record other sound on a different track while listening to the playback from a previously recorded track. This kind of recording is called overdubbing. 1 b 2 1 Press CUE to prepare for monitoring. Adjust the monitor volume using the respective TRACK knobs and the MONITOR knob. 2 Press ( PLAY. Playback begins. If necessary, you can use the jog dial to locate a specific point. To rerecord Follow the “Recording” procedure on the previous page.
Recording 7 Use the fader to adjust the recording level. Play a relatively loud phrase and make adjustments by watching the level meter for the track you want to record. If necessary, you can use the TRIM knob to adjust the recording level and equalizer. Adjust the recording level so that the CLIP indicator does not light. Adjust the TRIM knob so that the proper level is obtained when the fader is set between 7 and 8 to achieve good frequency characteristics.
Recording Auto Punch-In/Out Recording You can rerecord a certain portion of a previously recorded track. This is called punch-in/out recording. With this unit allows for 2 kinds of punch-in/out recording; auto punch-in/out, where you specify the section you desire and the unit punches in/out automatically, and manual punch-in/out, where you time the performance and punch-in/out manually at the positions you desire.
Recording 7 Use the fader to adjust the recording level. Play a relatively loud phrase and make adjustments by watching the level meter for the track you want to record. If necessary, you can use the TRIM knob to adjust the recording level and equalizer. Adjust the recording level so that the CLIP indicator does not light. Adjust the TRIM knob so that the proper level is obtained when the fader is set between 7 and 8 to achieve good frequency characteristics.
Recording 1 Recording Turn the jog dial to set the counter to the point you want to hear. Pressing the IN key automatically locates the punch-in point. 2 Press CUE to prepare for monitoring. Adjust the monitor volume using the respective TRACK knobs and the MONITOR knob. 3 Press ( PLAY. Playback begins. 2 1 3 To rerecord Follow the “Recording” procedure to the left. 1 Press AUTO PUNCH when the disc is stopped. The indicator on AUTO PUNCH lights.
Recording Manual Punch-In/Out Recording 5 Press CUE, then turn the TRACK knob corresponding to the track containing the recorded sound you want to hear while recording to adjust the sound to a level which can be monitored. Use the MONITOR knob to adjust the monitor level. 6 Use the fader to adjust the recording level. Play a relatively loud phrase and make adjustments by watching the level meter for the track you want to record.
Recording 4 Press ( PLAY when you reach the point where you want to stop recording (the punch out point). The REC key goes out and the unit stops recording and switches to playback mode. 5 Press p STOP. Playback ends. Checking the Recording 2 Setting the ASSIGN SW on the front of the unit to “REC IO” lets you use a foot switch (etc.) to activate punchin/out recording. See “System Settings” (page 17) for details.
Recording 3 Mix Write Recording (Basics) You can record other sounds on top of a previously recorded track. The following is an explanation of the mix write concept. Set the channel 2 ASSIGN switch and PAN knobs to direct the sound to track 1. (Set the chorus vocals input from channel 2 to be recorded on track 1.) Press down EXAMPLE: Recording a chorus on top of the vocals recorded on track 1.
Recording 9 Use the channel 1 and 2 faders to adjust the balance between the vocals and chorus to be recorded on track 1. You may also need to adjust the monitor balance at this time. Press the p STOP key after making the necessary adjustments. 10 Turn the jog dial to locate the point on the counter Mix Write Recording (Applied Operations) Mix write also comes in handy in a variety of other situations not mentioned on the previous pages.
Recording 3 Set the ASSIGN switches and PAN knobs for channels 1~4 to direct the sound to track 4. (Set the playback sounds input from the recorder to channels 1~4 to be recorded on track 4.) ASSIGN ASSIGN ASSIGN 1 2 1 2 1 2 1 2 3 4 3 4 3 4 3 4 PAN L 4 ASSIGN R PAN L R PAN L R R you want to hear. 2 Press CUE to prepare for monitoring. Adjust the monitor volume using the respective TRACK knobs and the MONITOR knob. 3 Press ( PLAY. Playback begins.
Recording Preparations Recording 1 Press REC. The unit switches to record pause mode. 1 8 2 Press ( PLAY. Recording begins. Play together with the previously recorded performance. 3 When you’ve finished playing, press p STOP. 4 3 2,6 7 5 1 30EN Press down the INPUT switches on channels 1~4. (Set channels 1~4 to receive the (TRACK) sound played back from the recorder.) 2 Set the faders for channels 1~4 to about 7 or 8.
Editing Part of a Song (Track Edit) Editing Part of a Song (Track Edit) Track Edit Overview Specifying the Locate Points The track editing operations let you specify a part (an arbitrary section of an arbitrary track) and copy it over another part, move it to another position, or remove the sound from it. You can also switch the positions of two parts. Additionally, you can edit between different songs as well as within the same song.
Editing Part of a Song (Track Edit) 2 Press MARK. The indicator on the MARK key starts blinking. 3 Press the key for the locate point you desire. • IN point : Press IN. • OUT point : Press OUT. • DEST (destination) point : Hold down the SHIFT key and press IN. • A~D (E~H) points : Press A~D (Hold down the SHIFT key and press A~D). The time/bar in the display is set as the respective locate point.
Editing Part of a Song (Track Edit) During rehearsal mode, press the = or + key to switch between increased or decreased volume after the locate point. 3 4 5 Turn the jog dial to adjust the position of the locate point. The locate point moves in proportion to the rotation of the jog dial each time the section is repeated. Copying a Part (Track Copy) You can copy part of a track and place it in another location.
Editing Part of a Song (Track Edit) 2 3 4 Turn the jog dial so that “Trak Copy” appears in the display. The name of the edit function starts blinking in the display. Press ENTER. The edit setting items appear in the display. You can move part of a track to a different position in a different track. IN OUT Destination point point point Turn the jog dial to display the setting you desire. This determines which tracks the part will be copied from and which tracks the part will be copied to.
Editing Part of a Song (Track Edit) 3 Press ENTER. The edit setting items appear in the display. 4 Turn the jog dial to display the setting you desire. This determines which tracks the part will be moved to. Use the jog dial to display the move destination track numbers in the space below the move origin track number indicator(s) ( 1 mark). Switching the Locations of 2 Parts (Track Exchange) You can switch the location one part of a track with another part of any other track.
Editing Part of a Song (Track Edit) 3 Press ENTER. The edit setting items appear in the display. 4 Turn the jog dial to display the setting you desire. This determines which tracks the parts will be exchanged to. Use the jog dial to display the exchange destination track number(s) below the exchange origin track number indicator(s) ( 1 mark). Erasing a Part (Track Erase) You can erase part of a track. The part which was erased becomes a part with no sound.
Editing Part of a Song (Track Edit) 3 Press ENTER. The edit setting items appear in the display. 4 Turn the jog dial to display the setting you desire. This determines which tracks the part will be erased from. Use the jog dial to display the track number(s) containing the part(s) to be erased below the respective track number indicator(s) ( 1 mark). Example display: 1 3 001:Ers1 3 To set other tracks press ENTER and proceed to the next step. Press EXIT to return to the original settings.
Changing the Construction of a Song (Section Edit) Section Edit Overview Using the Undo Function with section editing operations The section editing operations let you specify sections common to all 4 tracks and move them to other positions in the song, duplicate them, or remove them. You can also switch the positions of two sections. You can undo an edit immediately after execution if the undo indicator is lit green. To carry out the undo function, press UNDO.
Changing the Construction of a Song (Section Edit) Moving a Section (Section Move) You can move a section to a different place in the song. The section to be moved is inserted at the point specified by the destination point. 2 Turn the jog dial so that “Sect Move” appears in the display. The name of the edit function starts blinking in the display. 3 Press ENTER. “OK?” appears in the display. 001:Mov,OK? IN point OUT point Destination point A B C b B A 4 Press ENTER again.
Changing the Construction of a Song (Section Edit) 3 Switching the Locations of 2 Sections (Section Exchange) Press ENTER. “OK?” appears in the display. 001:Xcg,OK? You can switch the location of two sections. 4 Press ENTER again. The selected edit operation is carried out. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears.
Changing the Construction of a Song (Section Edit) 3 Inserting Another Section (Section Insert) 001:Ins,OK? This function lets you copy a section and insert it at another place in the song. 4 Press ENTER again. The selected edit operation is carried out. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears.
Changing the Construction of a Song (Section Edit) 3 Deleting a Section (Section Delete) Press ENTER. “OK?” appears in the display. 001:Del,OK? This function lets you delete a section of the song. 4 Press ENTER again. The selected edit operation is carried out. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears.
Editing Entire Songs (Song Edit) Editing Entire Songs (Song Edit) Song Edit Overview Copying a Song (Song Copy) The following sections show you how to divide a completed song and connect 2 adjacent songs (etc.) so you can easily locate the positions you desire on the recorded disc. This function lets you duplicate a song. Newly created copy is treated as a new recording and becomes the last song on the disc. This is a convenient way to backup songs before editing.
Editing Entire Songs (Song Edit) 6 7 Press ENTER again. The selected song is copied. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears. To carry out another edit operation in succession use the jog dial to specify the operation you desire. Moving a Song (Song Move) This function lets you change the order of the songs by moving the song you select to a different position.
Editing Entire Songs (Song Edit) 6 Turn the jog dial to display the number you want to move the selected song to. 7 Press ENTER “OK?” appears in the display. 8 9 Press ENTER again. The selected song is moved. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears. To carry out another edit operation in succession use the jog dial to specify the operation you desire.
Editing Entire Songs (Song Edit) 6 Turn the jog dial to display the song number you want to exchange the first song with. 7 Press ENTER “OK?” appears in the display. 8 Press ENTER again. The selected songs are exchanged. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears. To carry out another edit operation in succession use the jog dial to specify the operation you desire.
Editing Entire Songs (Song Edit) 5 6 Press ENTER again. The song is divided at the specified point. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears. To carry out another edit operation in succession use the jog dial to specify the operation you desire. Press EXIT. This completes the edit operation. Connecting 2 Songs (Song Combine) This function lets you combine two songs into one.
Editing Entire Songs (Song Edit) 3 Press ENTER. The edit setting items appear in the display. Cmb 002+003 4 Turn the jog dial to display the song number you want to combine as the first half of the new song. 5 Press ENTER. 6 Turn the jog dial to display the song number you want to combine as the second half of the new song. 7 Press ENTER “OK?” appears in the display. 8 9 Deleting a Song (Song Delete) This function allows you to easily delete a recorded song by specifying its song number.
Editing Entire Songs (Song Edit) 5 Press ENTER “OK?” appears in the display. 6 Press ENTER again. The selected songs are exchanged. To start over again from the beginning, or quit the edit operation, press EXIT instead of ENTER. When the edit operation has finished, the edit select screen reappears. To carry out another edit operation in succession use the jog dial to specify the operation you desire.
Editing the Entire Disc (Disc Edit) Overview This chapter shows you how to erase all the information on the disc and how to assign a disc name. The following is a list of disc editing functions : • Disc Erase (for erasing a disc) n page 50 • Disc Name (for naming a disc) n page 51 Erasing the Disc Contents (Disc Erase) This function erases the entire disc. Both the recorded audio data and the disc name will be erased. 1 3,4 5 2 1 Press EDIT. [EDIT] appears in the display.
Editing the Entire Disc (Disc Edit) Naming the Disc (Disc Name) 7 Press EXIT when the cursor is in the leftmost position or press ENTER when the cursor is in the rightmost position to enter the final name. To carry out another edit operation in succession use the jog dial to specify the operation you desire. 8 Press EXIT. This completes the edit operation. This function lets you assign names to the disc using upper and lower case letters of the alphabet, numbers, and symbols.
Synchronization with MIDI Equipment Advantages of Using MIDI Connecting this unit to an external MIDI system (Computer, Sequencer, Sound Module, etc.) allows you to create even higher quality recordings. For example, if you record the vocal and guitar tracks on this unit, you can synchronize them with sounds from a sound module played back through a sequencer (etc.) during mixdown. This method of mixing allows you to make recordings without using unnecessary tracks.
Synchronization with MIDI Equipment MIDI Synchronization Using the MIDI Clock You can use the MIDI clock to synchronize this unit with sequencers (etc.) that are not MTC (MIDI Time Code) compatible. A tempo map must be created in order to use the MIDI clock. Creating a tempo map Setting up tempo information creates the standard signal for synchronization and allows you to use the MIDI clock for synchronization with an external sequencers (etc.). You can assign up to 50 tempo maps to each song.
Synchronization with MIDI Equipment 3 Press ENTER. The tempo map setting display appears. 11 Turn the jog dial to display 02. 02:---- --01:---- --12 Repeat steps 3~9 to create the new tempo map. Tempo Tempo change position Tempo map number (blinking) Note If you do not want to change the tempo information, leave the tempo information numbers blank. 4 5 Press ENTER again. The indication for the tempo change position starts blinking. Tempo map 1 can only be set to the first bar.
Synchronization with MIDI Equipment 5 6 Press ENTER. The indication for the tempo change position starts blinking. Tempo map 1 can only be set to the first bar. Turn the jog dial to the right to display Del. 05: Del 100 Blinking 7 Press ENTER. “Deleted” appears in the display and tempo map 5 is deleted. The previous operations can also be used to delete tempo map 1. However, tempo map 1 should only be deleted after deleting all the other tempo maps from 2 up.
Synchronization with MIDI Equipment Example of a MIDI System The following explains the construction of a synchronized MIDI system using both MMC and MTC and a MIDI sound module. Connections Computer MIDI OUT MIDI interface MIDI OUT MMC signal MIDI IN MIDI IN Note data (etc.
Mixdown Mixdown Mixdown (Basics) The following explains how to dub the song to a master recorder (such as a DAT or MD recorder) while adjusting the volume balance and localization of each track once you have completed all necessary recording and editing. This process, of completing a song composed in 4 tracks by converting it to normal stereo (2 tracks), is called “mixdown”. This process is generally considered the most important part of music production.
Mixdown Mixdown (Applied Operations) How to use the TRACK jacks The TRACK 1~4 jacks on the top panel of this unit provide a direct output of the signals from each track recorded on the disc. This allows you to take full advantage of a limited number of external effectors. EXAMPLE: After recording a vocal on track 1 and a keyboard on track 2. • You want to add delay to the vocals. • You want to add flanging to the keyboard. • But you only have 1 effector.
Mixdown 4 Overdub the keyboard in stereo to tracks 3 and 4 while listening to the playback from tracks 1 and 2. (Song 1) Song 1 Song 2 Song 3 K (L) B K (R) G Vo 1 B K (L) Vo 2 G K (R) Use the Song Copy edit function to back up the keyboard part. The backup becomes Song 3. Song 2 Dr (L) Dr (L) +B+G Dr (R) Dr (R) Dr (L) +B+G Dr (R) B K (L) K (R) G K (R) Use bounce recording to mixdown all four parts to tracks 1 and 2.
Additional Information Troubleshooting Display Message List If this unit does not operate as expected, the problem may simply be an oversight, a disconnected cable or a setting error. Before calling a service technician, compare the symptoms of the problems with those listed below to see if you can correct the problem yourself. This unit uses the display area to show operating condition and error messages. The meaning of each message is explained below.
Additional Information System Limitations of MDs The recording system in your MD deck has limitations described below. Note, however, that these limitations are due to the inherent nature of the MD recording system itself and not to mechanical causes. “DISC FULL” lights up before the MD has reached the maximum recording time (60 or 74 minutes) When 255 songs have been recorded on the MD, “DISC FULL” lights up regardless of the total recorded time. More than 255 songs cannot be recorded on the MD.
Additional Information RETURN 1~2 (L/R) Type : Phone (Unbalanced) Input impedance : greater than 20 kohm Standard input level : –10 dBs (Max: + 10dBs) OUTPUTS STEREO OUT (L/R) Type : Phono (Unbalanced) Load impedance : greater than 20 kohm Standard output level : –10 dBs MONITOR OUT (L/R) Type : Phono (Unbalanced) Load impedance : greater than 20 kohm Standard output level : –10 dBs TRACK OUT (1~4) Type : Phone (Unbalanced) Load impedance : greater than 20 kohm Standard output level : –10 dBs AUX OUT (
Additional Information Glossary TOC (Table of Contents) The area in which nonmusical data, such as disc and track information is stored. Writing of TOC information marks the completion of record and edit operations. ATRAC (Adaptive TRansform Acoustic Coding) ATRAC is the sound compression technology that enables an MD to contain the same length of music as a CD, despite the smaller physical size of the MD. ATRAC cuts the sounds imperceptible by the human ear to compress the data to 1/5 the original size.
Additional Information Block Diagram The block diagram for this unit is shown below.
Additional Information Sony Multi Track Recorder MDM-X4 MIDI Implementation Chart Function... Transmitted Recognized Basic Channel Default Changed Mode Default Messages Altered * * * * * * * * * * * * * * True Voice * * * * * * * * * * * * * * Note Number: SEP 21, 1996 Version: 1.
Track sheet (Make copies as necessary.) Répertoire des pistes (Faites autant de photocopies que nécessaire) Spurübersicht (Gegebenenfalls kopieren) Sony MDM-X4 Track Sheet Title Date Note Song No. Track No.
Remballage AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, éviter d’exposer l’appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un technicien qualifié. Précautions Sécurité • Attention — L’utilisation d’instruments optiques avec ce produit augmente le danger pour les yeux.
Au sujet de ce manuel TABLE DES MATIèrES Vue d’ensemble du MDM-X4 Procédures d’enregistrement standard ...................................................................... 4 Le symbole suivant est utilisé dans ce manuel: Donne des conseils supplémentaires pour faciliter l’utilisation. Appellation et fonction des organes Mixeur .............................................................................................................................. 6 Enregistreur ....................................
Vue d’ensemble du MDM-X4 µ Procédures d’enregistrement standard Le MDM-X4 est un enregistreur/mixeur multipiste intégré qui peut enregistrer jusqu’à 4 pistes avec des minidisques MD-DATA. En plus des possibilités d’enregistrement et de lecture 4 pistes, cet appareil peut effectuer des opérations de montage variées. 1 Raccordement des instruments, des microphones, des effecteurs (etc.), et préparation de l’enregistrement.
Vue d’ensemble du MDM-X4 µ 6 Vous décidez de changer la structure de la chanson. Les fonctions de montage vous permettent d’ajouter (ou supprimer) un chœur supplémentaire ou de répéter l’introduction au milieu d’un morceau (etc.) sans avoir à réenregistrer. Voir “Changement de structure d’un morceau (Section Edit)” (page 38) pour les détails. Piste µ 7 Repiquage de pistes sur une platine MD ou DAT extérieure en utilisant le mixeur pour régler l’équilibre. Voir “Mixdown” (page 57) pour les détails.
Appellation et fonction des organes Mixeur Se référer aussi au “Schéma fonctionnel” à la page 64. Section canal 1 à canal 4 Les fonctions décrites sont les mêmes pour chaque canal (1 à 4). 2 Touches de sélection d’entrée (INPUT) Vous permettent de sélectionner LINE/MIC (son des prises INPUT CH) ou TRACK 1 à 4 (son de l’enregistreur) pour l’acheminement vers les canaux 1 à 4 du mixeur. LINE/MIC: A utiliser pour l’entrée des sons extérieurs provenant d’un instrument ou d’un microphone (etc.).
Appellation et fonction des organes 8 Boutons de commande panoramique (PAN) Ajustent l’équilibre sonore du bus stéréophonique ou de groupe. Tournez vers “L” pour déplacer le son vers le bus de groupe 1 ou 3 et le côté “L” du bus stéréophonique. Tournez vers “R” pour déplacer le son vers le bus de groupe 2 ou 4 et le côté “R” du bus stéréophonique. 9 Potentiomètres 1 à 4 Ajustent le volume de chaque canal.
Appellation et fonction des organes 9 Boutons TRACK 1 à 4 Utilisez-les pour ajuster l’équilibre sonore d’ensemble quand vous contrôlez la lecture à partir de l’enregistreur (contrôle CUE) en tournant le bouton correspondant à chaque piste comme vous le souhaitez. Quand vous utilisez la fonction de contrôle CUE, n’oubliez pas d’appuyer sur la touche de réglage de piste de contrôle CUE (0 ci-dessous).
Appellation et fonction des organes 3 Touche OUT Règle le point de sortie (point de fin de montage). !£ Fente d’introduction du minidisque Insérez le minidisque dans cette fente. 4 Touche IN/DEST Règle le point d’entrée (point de début de montage). Appuyez sur cette touche en maintenant SHIFT enfoncé pour régler le point de destination (point de destination de montage). !¢ Touche REPEAT/DISPLAY Appuyez sur cette touche pour activer le mode de répétition de lecture.
Appellation et fonction des organes !¶ Touche de répétition RHSL (Rehearsal) Cette touche a deux fonctions: • Répétition d’enregistrement (fonction de répétition) Appuyez sur cette touche en mode de pause d’enregistrement pour faire clignoter le témoin et régler l’appareil afin qu’il fonctionne comme s’il enregistrait, mais sans enregistrer réellement. Ce mode est appelé mode de répétition. (Le mode de répétition peut aussi être mis en service en appuyant sur RHSL quand la touche AUTO PUNCH est allumée.
Appellation et fonction des organes 5 Indicateur [EDIT] S’allume pendant les opérations de montage (piste, section, morceau, minidisque). 6 Indicateur [SYSTEM] S’allume pendant les opérations de réglage du système. Prises d’entrée et de sortie Panneau supérieur 7 Indicateurs R S’allument pour indiquer que la piste respective a été sélectionnée pour l’enregistrement à l’aide des touches REC SELECT. Le numéro de piste correspond au numéro de bus de groupe.
Appellation et fonction des organes 4 Prises OUTPUT AUX 1/2 Transmettent le son à utiliser comme son de sortie. Après avoir ajouté un effet extérieur au son transmis par ces prises, utilisez les prises RETURN 1/2 (L/R) pour retourner le son vers cet appareil. Panneau avant 1 Panneau arrière 2 1 2 3 1 Prise de casque HEADPHONES Branchez un casque avec fiche standard. 4 56 1 Prise MIDI THRU Relaie le signal reçu par la prise MIDI IN. 2 Prise MIDI OUT Transmet le signal MIDI.
Raccordements et sens du signal Raccordements pour l’enregistrement Raccordez des instruments, des microphones, des amplificateurs et des casques pour le contrôle comme montré ci-dessous.
Raccordements et sens du signal Raccordement d’appareils MIDI Raccordez des appareils MIDI comme montré dans le schéma ci-dessous. Pour des détails concernant les raccordements pour le fonctionnement synchronisé avec un séquenceur (etc.), voir “Synchronisation avec des appareils MIDI” (page 52 à 56). Le schéma suivant montre le parcours des signaux internes de cet appareil. 1 Séquenceur (etc.
Contrôle Préparations pour le contrôle Cet appareil vous permet de contrôler 4 types de signaux en fonction des nécessités. 1 Groupe 1, 2: A sélectionner pour contrôler les bus de groupe 1 et 2 du mixeur. Le son du bus de groupe 1 est acheminé sur le canal L (gauche) et le son du bus de groupe 2 sur le canal R (droit). Quand vous enregistrez, sélectionnez ce groupe pour contrôler le son enregistré. 2 Groupe 3, 4: A sélectionner pour contrôler les bus de groupe 3 et 4 du mixeur.
Contrôle EXEMPLE 3 : Réenregistrement d’une partie de la piste 1 en contrôlant le son des pistes 3 et 4 (pendant l’enregistrement punch-in/out, etc.) EXEMPLE 5 : Contrôle du son du bus stéréophonique (pour le mixdown, etc.) Tournez pour ajuster le niveau Appuyez Tournez pour ajuster le niveau EXEMPLE 4 : Mixage des pistes 1 à 4 pour l’enregistrement sur les pistes 1 et 2 (pendant l’enregistrement mix write, etc.
Réglage de l’environnement de fonctionnement Réglages du système Vous pouvez personnaliser l’environnement de fonctionnement en mettant en/hors service les fonctions de synchronisation MIDI et UNDO (annulation de la dernière opération), etc. Réglage du diapason (Pitch) Vous pouvez régler le diapason par incréments de 0,25% dans une plage de ±8%.
Réglage de l’environnement de fonctionnement Réglage du nombre de pistes enregistrables sur le minidisque (Rec) Pour régler le nombre de pistes à utiliser sur le minidisque. Le nombre de pistes sélectionné est effectif la prochaine fois qu’un morceau est enregistré. Pendant la lecture, le nombre de pistes est sélectionné automatiquement suivant les caractéristiques du minidisque source. Les pistes pouvant être sélectionnées diffèrent aussi selon le type de minidisque utilisé (MD-DATA ou MD musical).
Enregistrement Enregistrement Enregistrement initial 7 Utilisez le potentiomètre pour ajuster le niveau d’enregistrement. Jouez une phrase relativement bruyante et effectuez les réglages en surveillant le crête-mètre correspondant à la piste que vous voulez enregistrer. Si nécessaire, vous pouvez utiliser le bouton TRIM pour ajuster le niveau d’enregistrement et l’égaliseur. Ajustez le niveau d’enregistrement de telle façon que le témoin CLIP ne s’allume pas.
Enregistrement Vérification de l’enregistrement Enregistrement overdub Vous pouvez enregistrer d’autres sons sur une piste différente en écoutant la lecture d’une piste précédemment enregistrée. Ce type d’enregistrement est appelé “enregistrement overdub”. 1 Piste b 2 1 2 Appuyez sur CUE pour préparer le contrôle. Ajustez le volume de contrôle avec les boutons TRACK respectifs et le bouton MONITOR. Appuyez sur ( PLAY. La lecture commence.
Enregistrement 7 Utilisez le potentiomètre pour ajuster le niveau d’enregistrement. Jouez une phrase relativement bruyante et effectuez les réglages en surveillant le crête-mètre correspondant à la piste que vous voulez enregistrer. Si nécessaire, vous pouvez utiliser le bouton TRIM pour ajuster le niveau d’enregistrement et l’égaliseur. Ajustez le niveau d’enregistrement de telle façon que le témoin CLIP ne s’allume pas.
Enregistrement Enregistrement punch-in/out automatique Vous pouvez réenregistrer une certaine partie d’une piste précédemment enregistrée. Cette opération est appelée “enregistrement punch-in/out”.
Enregistrement 7 Utilisez le potentiomètre pour ajuster le niveau d’enregistrement. Jouez une phrase relativement bruyante et effectuez les réglages en surveillant le crête-mètre correspondant à la piste que vous voulez enregistrer. Si nécessaire, vous pouvez utiliser le bouton TRIM pour ajuster le niveau d’enregistrement et l’égaliseur. Ajustez le niveau d’enregistrement de telle façon que le témoin CLIP ne s’allume pas.
Enregistrement 1 Enregistrement Tournez la molette de recherche pour régler le compteur sur le point que vous voulez entendre. Quand vous appuyez sur la touche IN, le point punch-in est automatiquement localisé. 2 Appuyez sur CUE pour préparer le contrôle. Ajustez le volume de contrôle avec les boutons TRACK respectifs et le bouton MONITOR. 3 Appuyez sur ( PLAY. La lecture commence. 2 1 3 Pour réenregistrer Suivez la procédure “Enregistrement” à gauche.
Enregistrement Enregistrement “punch-in/out” manuel L’enregistrement punch-in/out manuel est effectué quand vous commencez et arrêtez l’enregistrement manuellement avec la durée appropriée au lieu de prérégler la partie à enregistrer. 5 Appuyez sur CUE, puis tournez le bouton TRACK correspondant à la piste contenant le son enregistré que vous voulez écouter en enregistrant, pour ajuster le son à un niveau permettant le contrôle. Utilisez le bouton MONITOR pour ajuster le niveau de contrôle.
Enregistrement 4 5 Appuyez sur ( PLAY quand vous atteignez le point où vous voulez arrêter l’enregistrement (le point punch-out). Le témoin de la touche REC s’éteint, l’enregistrement s’arrête et l’appareil passe en mode de lecture. 5 Appuyez sur p STOP. La lecture s’arrête. Vérification de l’enregistrement Appuyez sur p STOP. La lecture s’arrête. Régler ASSIGN SW à l’avant de l’appareil sur “REC IO” vous permet d’utiliser un interrupteur au pied (etc.) pour activer l’enregistrement punch-in/out.
Enregistrement 3 Enregistrement mix write (principes fondamentaux) Vous pouvez enregistrer d’autres sons sur une piste précédemment enregistrée. Cette section présente une explication du concept de mix write. Réglez le commutateur ASSIGN du canal 2 et les boutons PAN pour diriger le son vers la piste 1. (Réglez l’entrée du chœur du canal 2 pour qu’il soit enregistré sur la piste 1.
Enregistrement 9 Utilisez les potentiomètres des canaux 1 et 2 pour régler l’équilibre entre les voix et le chœur à enregistrer sur la piste 1. Il peut être aussi nécessaire de régler l’équilibre de contrôle à ce moment. Appuyez sur la touche p STOP après avoir effectué les réglages nécessaires. 10 Tournez la molette de recherche pour localiser le point sur le compteur où l’enregistrement commencera. 11 Appuyez sur la touche REC SELECT correspondant à la piste 1.
Enregistrement 3 Réglez les commutateurs ASSIGN et les boutons PAN correspondant aux canaux 1 à 4 pour diriger le son vers la piste 4. (Réglez l’entrée du son de lecture de l’enregistreur vers les canaux 1 à 4 pour qu’il soit enregistré sur la piste 4.) ASSIGN ASSIGN ASSIGN ASSIGN 1 2 1 2 1 2 1 2 3 4 3 4 3 4 3 4 PAN L 4 5 6 R PAN L R PAN L R Appuyez PAN L R Tournez complètement vers “R”. Préparez le contrôle.
Enregistrement Préparatifs Enregistrement 1 Appuyez sur REC. L’appareil passe en mode de pause d’enregistrement. 1 8 2 Appuyez sur ( PLAY. L’enregistrement commence. Effectuez simultanément la lecture du morceau précédemment enregistré. 3 Quand vous avez terminé la lecture, appuyez sur p STOP. 4 3 2,6 7 5 1 30F Appuyez sur les commutateurs INPUT des canaux 1 à 4. (Réglez les canaux 1 à 4 pour qu’ils reçoivent le son (TRACK) joué par l’enregistreur.
Montage d’une partie Montage d’une partie d’un morceau (Track Edit)d’un morceau (Track Edit) Vue d’ensemble du montage de piste (Track Edit) Spécification des points de localisation Les opérations de montage de piste vous permettent de spécifier une partie (une section arbitraire d’une piste arbitraire) et de la copier sur une autre partie, de la déplacer vers une autre position, ou d’effacer le son qui s’y trouve. Vous pouvez aussi échanger la position de deux parties.
Montage d’une partie d’un morceau (Track Edit) 2 Appuyez sur MARK. Le témoin sur la touche MARK commence à clignoter. 3 Appuyez sur la touche correspondant au point de localisation souhaité. • Point IN: Appuyez sur IN. • Point OUT: Appuyez sur OUT. • Point DEST (destination): Appuyez sur IN en maintenant la touche SHIFT enfoncée. Le temps/mesure pour le point de localisation respectif apparaît sur l’afficheur.
Montage d’une partie d’un morceau (Track Edit) 3 4 Tournez la molette de recherche pour régler la position du point de localisation. Le point de localisation se déplace proportionnellement à la rotation de la molette chaque fois que la partie est répétée. Appuyez sur MARK. Le témoin sur la touche MARK commence à clignoter. Copie d’une partie (Track Copy) Vous pouvez copier une partie d’une piste et l’insérer à un autre endroit.
Montage d’une partie d’un morceau (Track Edit) 2 Tournez la molette de recherche afin que “Track Copy” apparaisse sur l’afficheur. Le nom de la fonction de montage commence à clignoter sur l’écran. 3 Appuyez sur ENTER. Les paramètres de la fonction de montage apparaissent sur l’écran. 4 Tournez la molette de recherche pour afficher le réglage souhaité. Vous déterminez ainsi à partir de quelle piste la partie sera copiée et sur quelle piste elle sera recopiée.
Montage d’une partie d’un morceau (Track Edit) 3 Appuyez sur ENTER. Les paramètres de la fonction de montage apparaissent sur l’écran. 4 Tournez la molette de recherche pour afficher le réglage souhaité. Vous déterminez ainsi sur quelle piste la partie sera recopiée. Utilisez la molette de recherche pour spécifier le numéro des pistes de destination dans l’espace en-dessous des indicateurs de pistes d’origine (marque 1 ).
Montage d’une partie d’un morceau (Track Edit) 3 Appuyez sur ENTER. Les paramètres de la fonction de montage apparaissent sur l’écran. 4 Tournez la molette de recherche pour afficher le réglage souhaité. Vous déterminez ainsi sur quelles pistes les parties seront recopiées. Utilisez la molette de recherche pour afficher le numéro des pistes de destination dans l’espace en-dessous des indicateurs des pistes d’origine (marque 1 ).
Montage d’une partie d’un morceau (Track Edit) 3 Appuyez sur ENTER. Les paramètres de la fonction de montage apparaissent sur l’écran. 4 Tournez la molette de recherche pour afficher le réglage souhaité. Vous déterminez ainsi sur quelle piste la partie sera effacée. Utilisez la molette de recherche pour afficher le numéro de la piste contenant la partie à effacer sous les indicateurs de numéros de pistes respectifs (marque 1 ).
Changement de structure d’un morceau (Section Edit) Vue d’ensemble du montage de section (Section Edit) Les opérations de montage de section vous permettent de spécifier des sections communes aux 4 pistes et de les déplacer vers une autre position dans le morceau, de les copier ou de les éliminer. Vous pouvez aussi interchanger la position de deux sections.
Changement de structure d’un morceau (Section Edit) Déplacement de section (Section Move) Vous pouvez déplacer une section sur une position différente à l’intérieur d’un morceau. La section à déplacer est insérée au point spécifié comme point de destination. 2 Tournez la molette de recherche afin que “Sect Move” apparaisse sur l’afficheur. Le nom de la fonction de montage commence à clignoter sur l’écran. 3 Appuyez sur ENTER. “OK?” apparaît sur l’afficheur.
Changement de structure d’un morceau (Section Edit) 3 Échange de position de deux sections (Section Exchange) Appuyez sur ENTER. “OK?” apparaît sur l’afficheur. 001:Xcg,OK? Vous pouvez interchanger la position de deux sections. 4 Appuyez de nouveau sur ENTER. L’opération de montage sélectionnée est effectuée. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît.
Changement de structure d’un morceau (Section Edit) 3 Insertion d’une autre section (Section Insert) 001:Ins,OK? Cette fonction vous permet de copier une section et de l’insérer à un autre endroit dans le morceau. 4 Appuyez de nouveau sur ENTER. L’opération de montage sélectionnée est effectuée. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît.
Changement de structure d’un morceau (Section Edit) Effacement de section (Section Delete) Cette fonction vous permet d’effacer une section du morceau. 3 001:Del,OK? 4 Appuyez de nouveau sur ENTER. L’opération de montage sélectionnée est effectuée. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît.
Montage de morceaux complets (Song Edit) Montage de morceaux complets (Song Edit) Vue d’ensemble du montage de morceau (Song Edit) Copie d’un morceau (Song Copy) Les sections suivantes vous montrent comment diviser un morceau complété et réunir 2 morceaux adjacents (etc.) afin de pouvoir localiser facilement les positions souhaitées sur le minidisque enregistré. Cette fonction vous permet de recopier un morceau.
Montage de morceaux complets (Song Edit) 6 7 Appuyez de nouveau sur ENTER. Le morceau sélectionné est copié. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît. Pour effectuer une autre opération de montage à la suite, utilisez la molette de recherche pour spécifier l’opération souhaitée. Appuyez sur EXIT. L’opération de montage est maintenant terminée.
Montage de morceaux complets (Song Edit) 6 Tournez la molette de recherche pour afficher le numéro correspondant à la position sur laquelle vous voulez déplacer le morceau. 7 Appuyez sur ENTER. “OK?” apparaît sur l’afficheur. 8 Appuyez de nouveau sur ENTER. Le morceau sélectionné est déplacé. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît.
Montage de morceaux complets (Song Edit) 6 Tournez la molette de recherche pour afficher le numéro du morceau que vous voulez échanger avec le premier morceau. 7 Appuyez sur ENTER. “OK?” apparaît sur l’afficheur. 8 Appuyez de nouveau sur ENTER. Les morceaux sélectionnés sont échangés. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît.
Montage de morceaux complets (Song Edit) 5 6 Appuyez de nouveau sur ENTER. Le morceau est divisé au point spécifié. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît. Pour effectuer une autre opération de montage à la suite, utilisez la molette de recherche pour spécifier l’opération souhaitée. Appuyez sur EXIT. L’opération de montage est maintenant terminée.
Montage de morceaux complets (Song Edit) 3 Appuyez sur ENTER. Les paramètres de réglage de montage apparaissent sur l’afficheur. Cmb 002+003 4 Tournez la molette de recherche pour afficher le numéro du morceau que vous voulez combiner comme première moitié du nouveau morceau. 5 Appuyez sur ENTER. 6 Tournez la molette de recherche pour afficher le numéro du morceau que vous voulez combiner comme seconde moitié du nouveau morceau. 7 Appuyez sur ENTER. “OK?” apparaît sur l’afficheur.
Montage de morceaux complets (Song Edit) 5 Appuyez sur ENTER. “OK?” apparaît sur l’afficheur. 6 Appuyez de nouveau sur ENTER. Les morceaux sélectionnés sont effacés. Pour recommencer à partir du début, ou quitter l’opération de montage, appuyez sur EXIT au lieu de ENTER. Quand l’opération de montage est terminée, l’écran de sélection de montage réapparaît. Pour effectuer une autre opération de montage à la suite, utilisez la molette de recherche pour spécifier l’opération souhaitée.
Montage du minidisque entier (Disc Edit) Vue d’ensemble Ce chapitre vous montre comment effacer toutes les informations du minidisque et comment assigner un titre au minidisque. Vous trouverez ci-dessous une liste des fonctions de montage de minidisque: • Disc Erase (pour effacer un minidisque) n page 50 • Disc Name (pour titrer un minidisque) n page 51 Effacement du contenu d’un minidisque (Disc Erase) Cette fonction efface le minidisque tout entier.
Montage du minidisque entier (Disc Edit) Titrage du minidisque (Disc Name) Cette fonction vous permet d’assigner des titres aux morceaux en utilisant les majuscules et les minuscules de l’alphabet, des nombres et des symboles. Vous pouvez utiliser jusqu’à 11 caractères. 5 Appuyez sur ENTER. Le caractère sélectionné à l’étape 4 s’allume en continu et le curseur commence à clignoter dans la position suivante. Pour revenir à la position précédente, appuyez sur EXIT.
Synchronisation avec des appareils MIDI Avantages de l’utilisation du MIDI Raccorder cet appareil à un appareil MIDI extérieur (ordinateur, séquenceur, module sonore, etc.) vous permet de créer des enregistrements de qualité encore plus élevée. Par exemple, si vous enregistrez les pistes voix et guitare sur cet appareil, vous pouvez les synchroniser avec des sons provenant d’un module sonore lus par l’intermédiaire d’un séquenceur (etc.) pendant le mixdown.
Synchronisation avec des appareils MIDI Synchronisation MIDI avec horloge MIDI Vous pouvez utiliser l’horloge MIDI pour synchroniser cet appareil avec des séquenceurs (etc.) qui ne sont pas compatibles MTC (MIDI Time Code). Une allocation de rythme doit être créée de façon à pouvoir utiliser l’horloge MIDI. 2 Réglez le séquenceur pour qu’il accepte la synchronisation avec l’horloge MIDI extérieure. La lecture des données de chanson MIDI devient ainsi possible.
Synchronisation avec des appareils MIDI 3 Appuyez sur ENTER. L’affichage de réglage de l’allocation de rythme apparaît. 01:---- --- 11 Tournez la molette de recherche pour afficher 02. 02:---- --12 Répétez les étapes 3 à 9 pour créer la nouvelle allocation de rythme. Quand l’allocation de rythme est créée, les réglages sont affichés dans l’ordre automatiquement en commençant par la position du premier changement de rythme.
Synchronisation avec des appareils MIDI 3 4 Appuyez sur ENTER. L’affichage de réglage de l’allocation de rythme apparaît. Tournez la molette de recherche pour afficher l’allocation de rythme 05. 05:0018 100 Clignotant 5 Appuyez sur ENTER. L’indicateur de position de changement de rythme commence à clignoter. L’allocation de rythme 1 peut être réglée seulement pour la première mesure. 6 Tournez la molette de recherche vers la droite pour afficher Del. 05: Del 100 Clignotant 7 Appuyez sur ENTER.
Synchronisation avec des appareils MIDI Exemple de système MIDI Vous trouverez ci-après des explications sur la construction d’un système MIDI synchronisé utilisant MMC et MTC ainsi qu’un module sonore MIDI. Raccordements Ordinateur MIDI IN MIDI OUT Interface MIDI MIDI OUT Signal MMC MIDI IN Données de notes (etc.
Mixdown Mixdown Mixdown (principes fondamentaux) Vous trouverez ci-après des explications sur la façon de repiquer un morceau sur un enregistreur final (tel qu’un enregistreur DAT ou MD) tout en réglant l’équilibre du volume sonore et la localisation de chaque piste après avoir terminé les enregistrements et montages nécessaires.
Mixdown Mixdown (applications) Comment utiliser les prises TRACK Les prises TRACK 1 à 4 du panneau supérieur de cet appareil offrent une sortie directe aux signaux de chaque piste enregistrée sur le minidisque. Vous pouvez ainsi tirer le meilleur parti d’un nombre limité d’effecteurs extérieurs. EXEMPLE: Après avoir enregistré les voix sur la piste 1 et un clavier sur la piste 2. • Vous voulez ajouter du retard aux voix. • Vous voulez ajouter du flanging au clavier. • Mais vous avez seulement un effecteur.
Mixdown 4 Ajoutez le clavier en stéréo aux pistes 3 et 4 en écoutant la lecture des pistes 1 et 2. (Morceau 1) Morceau 1 Morceau 2 Dr (L) Dr (L) +B+G Dr (R) Dr (R) 5 B Morceau 1 K (R) G Dr+K(L) Dr (L) +B+G Dr+K(R) Dr (R) Utilisez la fonction de repiquage d’un morceau pour sauvegarder la partie clavier. La partie sauvegardée devient le morceau 3.
Informations complémentaires Guide de dépannage Liste des messages affichés Si l’appareil ne fonctionne pas normalement, il se peut que le problème soit un simple oubli, un cordon débranché ou une erreur de réglage. Avant de faire appel à un technicien, veuillez comparer les symptômes du problème en question avec ceux de la liste ci-après pour voir si vous ne pouvez pas porter remède vous-même à la difficulté.
Informations complémentaires Limites du système d’enregistrement de minidisque Le système d’enregistrement de votre platine MD a les limites décrites ci-dessous. Notez bien que ces limites sont liées à la nature du système d’enregistrement MD et ne sont pas dues à des défaillances mécaniques. “DISC FULL” s’allume avant que le temps d’enregistrement maximal du minidisque (60 ou 74 minutes) soit atteint.
Informations complémentaires RETURN 1 et 2 (L/R) Type : Jack quart de pouce (Asymétrique) Impédance d’entrée : supérieure à 20 kilohms Niveau d’entrée nominal : –10 dB (Max: +10 dB) Sorties STEREO OUT (L/R) Type : Cinch (Asymétrique) Impédance de charge : supérieure à 20 kilohms Niveau de sortie nominal : –10 dB MONITOR OUT (L/R) Type : Cinch (Asymétrique) Impédance de charge : supérieure à 20 kilohms Niveau de sortie nominal : –10 dB TRACK OUT (1 à 4) Type : Jack quart de pouce (Asymétrique) Impédance
Informations complémentaires Glossaire TOC (Sommaire) Zone dans laquelle les données non musicales, telles que les informations de minidisque et de piste, sont stockées. L’écriture des données de sommaire marque la fin de l’enregistrement et du montage. ATRAC (Adaptive TRansform Acoustic Coding) ATRAC est un mode de compression du son qui permet à un minidisque de contenir la même durée de musique qu’un CD, malgré les dimensions plus faibles du minidisque.
Informations complémentaires Schéma fonctionnel Le schéma fonctionnel pour cet appareil est montré cidessous to CHANNEL 64F
Informations complémentaires Sony Multi Track Recorder MDM-X4 Tableau de mise en applIcation MIDI Function... Transmitted Recognized Basic Channel Default Changed Mode Default Messages Altered * * * * * * * * * * * * * * True Voice * * * * * * * * * * * * * * Note Number: Velocity Note ON Note OFF After Touch Key’s Ch’s SEP 21, 1996 Version: 1.
Zur Wiederverpackung WARNUNG Um Feuergefahr und die Gefahr eines elektrischen Schlags zu vermeiden, setzen Sie das Gerät weder Regen noch sonstiger Feuchtigkeit aus. Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur einem Fachmann. Stellen Sie das Gerät nicht auf ein Bücherregal, in einen geschlossenen Schrank usw., da sich der Hauptnetzschalter (MAIN POWER) an der Rückseite befindet.
Zu dieser Anleitung In der Anleitung wird das folgende Symbol verwendet: Tips zur Bedienungserleichterung. Inhaltsverzeichnis Überblick über den MDM-X4 Grundlegendes Aufnahmeverfahren ......................................................................... 4 Bezeichnung und Funktion der Teile Der Mischer ..................................................................................................................... 6 Recorder ..........................................................................
Überblick über den MDM-X4 µ Grundlegendes Aufnahmeverfahren Der MDM-X4 besteht aus einem Mehrkanal-Recorder und -Mischer. Bis zu vier Spuren können auf eine MDDATA-Disc aufgenommen werden. Darüber hinaus stehen eine eine Reihe von Editierfunktionen zur Verfügung. 1 Schließen Sie die Instrumente, die Mikrofone, die Effektgeräte usw. an, und bereiten Sie den Aufnahmebetrieb vor. 4 Sie wollen einen Begleitchor aufnehmen, es ist jedoch keine Spur mehr frei.
Überblick über den MDM-X4 µ 6 Die Struktur eines Songs soll geändert werden. Mit den Editierfunktionen können Sie einen weiteren Chor hinzufügen (oder löschen), die Einführung in der Mitte des Songs wiederholen usw., ohne eine zusätzliche Aufnahme auszuführen. Einzelheiten finden Sie unter „Ändern der Struktur eines Songs (Sektor-Editierbetrieb)“ auf Seite 38. Spur µ 7 Überspielen Sie die Spuren mit der gewünschten Mischbalance auf ein externes MD- oder DAT-Deck.
Bezeichnung und Funktion der Teile Der Mischer Siehe auch das „Blockdiagramm“ auf Seite 64. Bedienfeld für Kanäle 1 - 4 Die im folgenden beschriebenen Funktionen sind für alle Kanäle (1 - 4) gleich. 2 INPUT-Wahltasten Mit diesen Tasten wird das Eingangssignal für die Mischerkanäle 1 bis 4 gewählt; es kann zwischen LINE/MIC (Signal der INPUT CH-Buchsen) und TRACK 1 - 4 (Signal des Recorders) gewählt werden. LINE/MIC: Zur Wahl des Eingangssignals eines externen Instrumentes, Mikrofons usw.
Bezeichnung und Funktion der Teile 7 ASSIGN-Tasten Diese Tasten legen fest, welchem Gruppen-Bus die Kanäle zugeordnet werden (d.h. auf welcher Spur sie aufgezeichnet werden). Das Signal des Kanals wird stets dem Stereo-Bus zugeleitet. Beispiel: Die Kanäle 2 und 3 werden dem GruppenBus 1 zugeordnet (der Recorder zeichnet sie auf Spur 1 auf). Drücken ASSIGN ASSIGN ASSIGN ASSIGN 1 2 1 2 1 2 1 2 3 4 3 4 3 4 3 4 8 PAN-Regler Zur Einstellung der Balance des Stereo- oder GruppenBus.
Bezeichnung und Funktion der Teile 8 ASSIGN-Tasten Diese Tasten legen fest, welchem Gruppen-Bus (1 - 4) das Return-Signal (Rücklaufsignal) zugeordnet wird (d.h. auf welcher Spur der Recorder die Signale aufzeichnet). Recorder Bedienungspult Beispiel: Rücklaufsignal 1 und 2 wird dem GruppenBus 1 und 2 zugeordnet (der Recorder zeichnet die Signale auf den Spuren 1 und 2 auf).
Bezeichnung und Funktion der Teile 3 OUT-Taste Zur Festlegung des Out-Punktes (Schnittausstiegspunkt). und OUT-Punkt wird wiederholt wiedergegeben. Durch Drücken der Taste im Stoppmodus werden die TOC-Daten* auf die Disc geschrieben. 4 IN/DEST-Taste Zur Festlegung des IN-Punktes (Schnitteinstiegspunkt). Zur Festlegung des DEST-Punktes (Schnittzielpunkt) ist diese Taste bei gleichzeitig gedrückt gehaltener SHIFT-Taste zu drücken. !™ § EJECT-Taste Zum Herausnehmen der Disc.
Bezeichnung und Funktion der Teile !ª ENTER-Taste Durch Drücken dieser Taste wird der gewählte Vorgang usw. ausgeführt. Pitch-Steuerung „Ein“: Die Aufnahme bzw. Wiedergabe wird mit dem voreingestellten PitchWert ausgeführt („Vari Pitch“ erscheint im Display). Pitch-Steuerung „Aus“: Die Aufnahme bzw. Wiedergabe wird mit dem normalen Pitch-Wert ausgeführt („Fixed Pitch“ erscheint im Display). Einzelheiten zur Pitch-Einstellung finden Sie unter „Systemeinstellungen“ auf Seite 17.
Bezeichnung und Funktion der Teile 1 Pegelmeter • 1-4 Bei der Wiedergabe: Der Ausgangspegel der einzelnen Spuren wird angezeigt. Bei der Aufnahme: Der Eingangspegel der einzelnen Spuren wird angezeigt. Im Stoppmodus oder wenn keine Disc eingelegt ist: Der Pegel von Gruppen-Bus 1 - 4 wird angezeigt. • L, R Der Pegel des Stereo-Bus wird angezeigt. Eingangs- und Ausgangsbuchsen Oberseite 2 Zähleranzeige Zeigt die Zeit (Minuten/Sekunden/Frame) oder den Takt (Takt/Schlag/Cock) an.
Bezeichnung und Funktion der Teile 3 CH 1-6-Eingangsbuchsen Zum Einspeisen von Tonsignalen für die Kanäle 1-6. Die CH 1 - 4-Buchsen sind für Mikrofonsignale und Line-Signalquellen bestimmt. Die Buchsen CH 5 und 6 sind ausschließlich für Line-Signalquellen bestimmt. In die Buchsen von Kanal 1 und 2 können XLR-Stecker direkt eingesteckt werden. (Die Eingänge für Kanal 1 und 2 sind symmetrisch; es können sowohl XLR- als auch Standardstecker verwendet werden.
Anschluß und Signalfluß Anschluß für Aufnahme Schließen Sie die Instrumente, die Mikrofone sowie den Verstärker und den Kopfhörer (für Monitorbetrieb) wie folgt an: Externer Verstärker und Lautsprecher Instrumente und Mikrofone An INPUT CH-1-CH-6-Buchsen (an CH-1 und CH-2 können XLR-Stecker angeschlossen werden) Von MONITOR OUT-Buchsen an der Rückseite des Geräts Von HEADPHONES-Buchsen an der Vorderseite des Geräts Von den STEREO OUT-Buchsen an der Rückseite des Geräts Für das Abmischen verwendetes Au
Anschluß und Signalfluß Anschluß eines MIDI-Geräts MDM-X4-Signalflußdiagramm Ein MIDI-Gerät wird wie folgt angeschlossen. Einzelheiten zum Synchronbetrieb mit einem Sequencer usw. finden Sie unter „Synchronisation mit einem MIDI-Gerät“ auf Seite 52-56. Das folgende Diagramm zeigt den internen Signalfluß. 1 3 4 Sequencer MIDI IN-Buchse MIDI OUT-Buchse Für direkte Ausgabe des über die MIDI IN-Buchse eingespeisten MIDI-Signals zu einem anderen MIDI-Gerät.
Monitorbetrieb Vorbereitung des Monitorbetriebs Im Monitorbetrieb können mit diesem Gerät die folgenden vier Signaltypen abgehört werden. 1 Group 1, 2: Zum Abhören des Mischer-GruppenBus 1 und 2. Der Ton des Gruppen-Bus 1 befindet sich im linken Kanal (L) und der des Gruppen Bus 2 im rechten Kanal (R). Beim Aufnahmebetrieb ermöglicht diese Einstellung ein Abhören des Aufnahmetons. 2 Group 3, 4: Zum Abhören des Mischer-GruppenBus 3 und 4.
Monitorbetrieb Beispiel 3: Ein Teil von Spur 1 wird bespielt, während gleichzeitig Spur 3 und 4 abgehört wird (während Punch-In/OutAufnahme usw.) Beispiel 5: Das Stereo-Bus-Tonsignal wird abgehört (zum Abmischen usw.) Zur Pegeleinstellung Drücken Drücken Zur Pegeleinstellung Zur Pegeleinstellung Beispiel 4: Die Spuren 1 bis 4 werden gemischt auf die Spuren 1 und 2 aufgenommen (während Mischaufnahme usw.) Die CUE-MonitorFunktion ist nicht erforderlich Das Mischen erfolgt mit der Mischfunktion.
Wunschgemäßes Konfigurieren des Geräts Systemeinstellungen Um das Gerät wunschgemäß zu konfigurieren schalten Sie je nach den Erfordernissen die MIDISynchronisation, die UNDO-Funktion usw. ein oder aus. Pitch-Einstellung (Pitch) Der Pitch kann in 0,25%-Schritten innerhalb eines Bereichs von ±8% variiert werden. Wenn nach der Einstellung der Pitch-Betriebsmodus eingeschaltet wird, führt das Gerät die Aufnahme/Wiedergabe mit dem eingestellten Pitch-Wert aus.
Wunschgemäßes Konfigurieren des Geräts Aufnahmemodus Verwendbare Aufnahmezeit Spuren 4 1~4 2 1 Disc-Typ 1, 2 37 Min. 74 Min. MD DATA MD DATA, Musik-MD 1 148 Min. MD DATA, Musik-MD Ändern von Einstellungen Zum Ändern von Systemeinstellungen verfahren Sie wie folgt. Hinweis Im Aufnahmemodus schaltet das Gerät bei Musik-MDs automatisch auf 2-Spur-Modus, auch wenn zuvor 4-SpurModus gewählt war.
Aufnahme Aufnahme Erstaufnahme Zum Aufnehmen auf die erste Spur einer leeren Disc verfahren Sie wie folgt. Track Spur 1 2 3 4 6 Stellen Sie am MONITOR-Regler die Lautstärke des Mithörtons ein. 7 Stellen Sie am Faderregler den Aufnahmepegel ein. Geben Sie hierzu eine relativ laute Passage wieder und beobachten Sie beim Einstellen das Pegelmeter der Spur, auf die aufgenommen werden soll. Falls erforderlich, stellen Sie auch die TRIMRegler und die Klangregler ein.
Aufnahme Überprüfen der Aufnahme Overdub-Aufnahme Beim Aufnehmen auf eine Spur kann gleichzeitig eine andere Spur abgehört werden (Mithöraufnahme). Spur 1 b Aufnahmesektor 2 1 2 Drücken Sie CUE, um den Monitorbetrieb vorzubereiten. Stellen Sie mit dem betreffenden TRACK-Reglern und dem MONITOR-Regler die Monitorlautstärke ein. Drücken Sie ( PLAY. Die Wiedergabe beginnt. Falls erforderlich, kann mit dem Jog-Knopf ein bestimmter Punkt aufgesucht werden.
Aufnahme 7 Stellen Sie am Faderregler den Aufnahmepegel ein. Geben Sie hierzu eine relativ laute Passage wieder und beobachten Sie beim Einstellen das Pegelmeter der Spur, auf die aufgenommen werden soll. Falls erforderlich, stellen Sie auch die TRIMRegler und die Klangregler ein. Achten Sie beim Einstellen stets darauf, daß die CLIP-Anzeige nicht leuchtet. Für optimale Klangcharakteristik sollte beim Einjustieren des TRIM-Reglers der Faderregler auf einer Position zwischen 7 und 8 stehen.
Aufnahme Auto Punch-In/Out-Aufnahme Im Punch-In/Out-Aufnahmebetrieb kann ein Teil einer existierenden Aufnahme neu bespielt werden. Dabei wird unter den folgenden beiden Betriebsarten unterschieden: Auto Punch-In/Out und manuelles Punch-In/Out. Beim Auto Punch-In/Out-Betrieb führt das Gerät nach der Festlegung der Passage die PunchIn/Out-Aufnahme automatisch aus. Beim manuellen Betrieb wird die Punch-In/Out-Aufnahme während der Darbietung manuell gestartet und gestoppt.
Aufnahme 7 Stellen Sie am Faderregler den Aufnahmepegel ein. Geben Sie hierzu eine relativ laute Passage wieder und beobachten Sie beim Einstellen das Pegelmeter der Spur, auf die aufgenommen werden soll. Falls erforderlich, stellen Sie auch die TRIMRegler und die Klangregler ein. Achten Sie beim Einstellen stets darauf, daß die CLIP-Anzeige nicht leuchtet. Für optimale Klangcharakteristik sollte beim Einjustieren des TRIM-Reglers der Faderregler auf einer Position zwischen 7 und 8 stehen.
Aufnahme 1 Aufnahme Suchen Sie mit dem Jog-Knopf den Zählerstand der Stelle auf, die Sie hören möchten. Durch Drücken der IN-Taste kehrt das Gerät zum Punch-In-Punkt zurück. 2 Drücken Sie CUE, um auf Monitorbereitschaft zu schalten. Stellen Sie mit den betreffenden TRACK-Reglern und dem MONITOR-Regler die Monitorlautstärke ein. 3 Drücken Sie ( PLAY. Die Wiedergabe beginnt. 2 1 3 1 Drücken Sie AUTO PUNCH bei gestoppter Disc.
Aufnahme Manuelle Punch-In/OutAufnahme Beim manuellen Punch-In/Out-Betrieb werden die Punkte des neu zu bespielenden Teils nicht vorab festgelegt, sondern die Aufnahme wird manuell gestartet und gestoppt. 5 Drücken Sie CUE, und stellen Sie dann den TRACK-Regler des Kanals, der während der Aufnahme mitgehört werden soll, so ein, daß der Ton zu hören ist. Stellen Sie am MONITOR-Regler die Lautstärke des Mithörtons ein. 6 Stellen Sie am Faderregler den Aufnahmepegel ein.
Aufnahme 4 Drücken Sie am gewünschten AufnahmeEndpunkt (Punch-Out-Punkt) die ( PLAYTaste. Die REC-Taste erlischt, und das Gerät schaltet von Aufnahme auf Wiedergabe um. 5 Drücken Sie p STOP. Die Wiedergabe endet. Überprüfen der Aufnahme 2 Wenn ASSIGN SW an der Vorderseite des Geräts auf REC IO steht, kann die Punch-In/Out-Aufnahme mit einem Fußschalter usw. gesteuert werden. Einzelheiten finden Sie unter „Systemeinstellungen“ auf Seite 17.
Aufnahme Mischaufnahme (Grundlagen) 3 Auf eine bereits bespielte Spur können zusätzliche Daten aufgezeichnet werden, ohne die ursprüngliche Aufzeichnung zu löschen. Das folgende Beispiel verdeutlicht diesen Vorgang. Stellen Sie den ASSIGN-Schalter von Kanal 2 und die PUNCH-Regler so ein, daß das Tonsignal zur Spur 1 geleitet wird. (Die Chorstimmen von Kanal 2 werden auf Spur 1 aufgezeichnet.
Aufnahme 9 Stellen Sie mit den Faderreglern von Kanal 1 und 2 die Pegelbalance, mit der die Vokalstimmen und der Chor auf Spur 1 aufgezeichnet werden sollen, ein. Eventuell muß gleichzeitig auch die Monitorbalance einjustiert werden. Am Ende der Einstellungen drücken Sie die p STOP-Taste.
Aufnahme 3 Stellen Sie die ASSIGN-Schalter und PAN-Regler der Kanäle 1 - 4 so ein, daß das Tonsignal zu Spur 4 geleitet wird. (Das den Kanäle 1 - 4 zugeleitete RecorderWiedergabe-signal wird auf Spur 4 aufgezeichnet.) ASSIGN ASSIGN ASSIGN ASSIGN 1 2 1 2 1 2 1 2 3 4 3 4 3 4 3 4 PAN L R PAN L R PAN L R R Ganz auf R drehen. 4 5 der Stelle auf, die Sie hören möchten. 2 Drücken Sie CUE, um auf Monitorbereitschaft zu schalten.
Aufnahme Vorbereitungen Aufnahme 1 Drücken Sie REC. Das Gerät schaltet auf Aufnahme-Pause. 1 8 2 Drücken Sie ( PLAY. Die Aufnahme beginnt. Musizieren Sie zusammen mit der zu hörenden vorhergehenden Aufnahme. 3 Am Ende drücken Sie p STOP. 4 3 2,6 7 5 1 30D Drücken Sie die INPUT-Schalter der Kanäle 1 - 4. (Die Signale der wiedergegebenen Spuren werden den Kanälen 1 - 4 zugeleitet.) 2 Stellen Sie die Faderregler der Kanäle 1 - 4 auf eine Position zwischen 7 und 8.
Editieren eines Song-Teils (Spur-Editierbetrieb) Editieren eines Song-Teils (Spur-Editierbetrieb) Überblick über den SpurEditierbetrieb Im Spur-Editierbetrieb kann ein beliebiger Teil einer beliebigen Spur an eine andere Stelle verschoben, kopiert oder gelöscht werden. Außerdem ist es auch möglich, zwei Teile zu vertauschen. Der Editierbetrieb kann einen einzelnen Song oder verschiedene Songs umfassen.
Editieren eines Song-Teils (Spur-Editierbetrieb) 2 Drücken Sie MARK Die Anzeige der MARK-Taste beginnt zu blinken. 3 Drücken Sie die Taste des gewünschten Suchpunktes. • Für IN-Punkt: Drücken Sie IN. • Für OUT-Punkt: Drücken Sie OUT. • Für DEST-Punkt (Zielpunkt): Halten Sie die SHIFT-Taste gedrückt und drücken Sie gleichzeitig IN. Der Zeit/Takt-Wert im Display wird als Suchpunkt übernommen.
Editieren eines Song-Teils (Spur-Editierbetrieb) Während des Rehearsal-Betriebs kann durch Drücken der = oder + Taste zwischen Pegelanstieg und Pegelabfall hinter dem Suchpunkt umgeschaltet werden. 3 4 5 Stellen Sie mit dem Jog-Knopf die Position des Suchpunktes ein. Bei jedem Wiederholdurchgang wird der Suchpunkt entsprechend der am Jog-Knopf vorgenommenen Einstellung verschoben. Kopieren eines Teils (Track Copy) Ein Teil einer Spur kann an eine andere Stelle kopiert werden.
Editieren eines Song-Teils (Spur-Editierbetrieb) 2 Drehen Sie den Jog-Knopf, so daß im Display die Editierfunktion „Trak Copy“ angezeigt wird. Der Name der Editierfunktion blinkt. 3 Drücken Sie ENTER. Die einzustellenden Editierparameter erscheinen im Display. 4 Legen Sie mit dem Jog-Knopf die Quell- und Zielspuren des Kopiervorgangs fest. Die Zielspuren erscheinen unterhalb der Markierungen der Quellspuren ( 1 ).
Editieren eines Song-Teils (Spur-Editierbetrieb) 3 Drücken Sie ENTER. Die einzustellenden Editierparameter erscheinen im Display. 4 Legen Sie mit dem Jog-Knopf den Verschiebevorgang fest: Drehen Sie den Jog-Knopf so, daß die Nummern der Zielspuren unterhalb der Quellspuren-Marke ( 1 ) erscheinen. Vertauschen von zwei Teilen (Track Exchange) Ein bestimmter Teil einer Spur kann gegen einen bestimmten anderen Teil einer beliebigen anderen Spur ausgetauscht werden.
Editieren eines Song-Teils (Spur-Editierbetrieb) 3 Drücken Sie ENTER. Die einzustellenden Editierparameter erscheinen im Display. 4 Legen Sie mit dem Jog-Knopf den Vertauschungsvorgang fest: Drehen Sie den Jog-Knopf so, daß die Nummern der Zielspuren unterhalb der Quellspuren-Marke ( 1 ) erscheinen. Löschen eines Teils (Track Erase) Ein bestimmter Teil einer Spur kann gelöscht werden; der gelöschte Teil liefert anschließend kein Tonsignal.
Editieren eines Song-Teils (Spur-Editierbetrieb) 3 Drücken Sie ENTER. Die einzustellenden Editierparameter erscheinen im Display. 4 Legen Sie mit dem Jog-Knopf die Spuren, in denen ein Teil gelöscht werden soll, fest: Drehen Sie den Jog-Knopf so, daß die Nummern der Spuren unterhalb der Marke ( 1 ) erscheinen. Beispiel: 1 3 001:Ers1 3 Nach jeder Festlegung drücken Sie ENTER. Durch Drücken von EXIT kann die ursprüngliche Einstellung zurückgerufen werden.
Ändern der Struktur eines Songs (Sektor-Editierbetrieb) Überblick über den SektorEditierbetrieb Im Sektor-Editierbetrieb kann ein sich über alle vier Spuren erstreckender Sektor an eine andere Stelle verschoben, kopiert oder gelöscht werden. Außerdem ist es auch möglich, zwei Sektoren zu vertauschen.
Ändern der Struktur eines Songs (Sektor-Editierbetrieb) Verschieben eines Sektors (Section Move) Ein bestimmter Sektor kann an eine andere Stelle des Songs verschoben werden. Der Sektor wird am Zielpunkt eingefügt. 2 Drehen Sie den Jog-Knopf, so daß im Display die Editierfunktion „Sect Move“ angezeigt wird. Der Name der Editierfunktion blinkt. 3 Drücken Sie ENTER. „OK?“ erscheint im Display. 001:Mov,OK? IN-Punkt OUT-Punkt 4 Drücken Sie ENTER erneut. Der gewählte Editiervorgang wird ausgeführt.
Ändern der Struktur eines Songs (Sektor-Editierbetrieb) Vertauschen von zwei Sektoren (Section Exchange) 3 Drücken Sie ENTER. „OK?“ erscheint im Display. 001:Xcg,OK? Zwei Sektoren können wie folgt vertauscht werden. 4 Drücken Sie ENTER erneut. Der gewählte Editiervorgang wird ausgeführt. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Ändern der Struktur eines Songs (Sektor-Editierbetrieb) 3 Kopieren und Einfügen eines Sektors (Section Insert) 001:Ins,OK? Ein bestimmter Sektor kann kopiert und an einer anderen Stelle des Songs eingefügt werden. 4 Drücken Sie ENTER erneut. Der gewählte Editiervorgang wird ausgeführt. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Ändern der Struktur eines Songs (Sektor-Editierbetrieb) Löschen eines Sektors (Section Delete) Ein bestimmter Sektor eines Songs kann wie folgt gelöscht werden. 3 001:Del,OK? 4 Drücken Sie ENTER erneut. Der gewählte Editiervorgang wird ausgeführt. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Editieren des ganzen Songs Editieren (Song-Editierbetrieb) des ganzen Songs (Song-Editierbetrieb) Überblick über den SongEditierbetrieb Im Song-Editierbetrieb können Sie die Songs auf der Disc so umarrangieren, daß die gewünschten Stellen bequem gefunden werden können. Es besteht beispielsweise die Möglichkeit, einen Titel zu unterteilen oder zwei Titel zu einem Titel zusammenzufügen.
Editieren des ganzen Songs (Song-Editierbetrieb) Verschieben eines Songs (Song Move) 1 3,5,6 7 Verschieben des dritten Songs vor den zweiten Song 2,4 1 Ein Song kann zu einer beliebigen anderen Stelle verschoben werden. Drücken Sie EDIT. [EDIT] erscheint im Display. 1 2 A 1 Drehen Sie den Jog-Knopf, so daß im Display die Editierfunktion „Song Copy“ angezeigt wird. Der Name der Editierfunktion blinkt. 3 Drücken Sie ENTER. Die Editierparameter erscheinen im Display.
Editieren des ganzen Songs (Song-Editierbetrieb) 6 Wählen Sie mit dem Jog-Knopf die Nummer des Songs, zu dem der gewählte Song verschoben werden soll. 7 Drücken Sie ENTER. „OK?“ erscheint im Display. 8 Drücken Sie ENTER erneut. Der gewählte Song wird verschoben. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Editieren des ganzen Songs (Song-Editierbetrieb) 6 Wählen Sie mit dem Jog-Knopf die Nummer des zweiten Songs, der gegen den ersten Song vertauscht werden soll. 7 Drücken Sie ENTER. „OK?“ erscheint im Display. 8 Drücken Sie ENTER erneut. Die Songs werden vertauscht. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Editieren des ganzen Songs (Song-Editierbetrieb) 5 6 Drücken Sie ENTER erneut. Der Song wird an der betreffenden Stelle unterteilt. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige. Falls erwünscht, kann mit dem Jog-Knopf ein weiterer Editiervorgang definiert werden. Drücken Sie EXIT. Der Editierbetrieb ist damit beendet.
Editieren des ganzen Songs (Song-Editierbetrieb) 3 Drücken Sie ENTER. Die Editierparameter erscheinen im Display. Cmb 002+003 4 Wählen Sie mit dem Jog-Knopf die Nummer des ersten der beiden zu kombinierenden Songs. 5 Drücken Sie ENTER. 6 Wählen Sie mit dem Jog-Knopf die Nummer des zweiten der zu kombinierenden Songs. 7 Drücken Sie ENTER. „OK?“ erscheint im Display. 8 Drücken Sie ENTER erneut. Die gewählten Songs werden kombiniert.
Editieren des ganzen Songs (Song-Editierbetrieb) 4 Wählen Sie mit dem Jog-Knopf die Nummer des zu löschenden Songs. 5 Drücken Sie ENTER. „OK?“ erscheint im Display. 6 7 Drücken Sie ENTER erneut. Der gewählte Song wird gelöscht. Um erneut von Anfang an zu beginnen oder den Editiervorgang zu stornieren, drücken Sie die EXIT-Taste statt der ENTER-Taste. Nach dem Editiervorgang erscheint wieder die Editierfunktions-Wahlanzeige.
Editieren der ganzen Disc (Disc-Editierbetrieb) Überblick Löschen einer Disc (Disc Erase) In den folgenden Abschnitten wird das Löschen einer ganzen Disc und das Zuteilen eines Disc-Namens behandelt. Mit dieser Funktion kann die Disc vollständig gelöscht werden. Das Löschen umfaßt sowohl die Audiodaten als auch den Disc-Namen.
Editieren der ganzen Disc (Disc-Editierbetrieb) Zuteilen eines Disc-Namens (Disc Name) Der Disc kann ein aus Großbuchstaben, Kleinbuchstaben, Ziffern und Symbolen bestehender Name zugeteilt werden. Der Name kann bis zu 11 Zeichen lang sein. 7 Drücken Sie EXIT, wenn sich der Cursor ganz links befindet oder drücken Sie ENTER, wenn sich der Cursor ganz rechts befindet, um den endgültigen Namen zu speichern. Falls erwünscht, kann mit dem Jog-Knopf ein weiterer Editiervorgang definiert werden.
Synchronisation mit einem MIDI-Gerät Vorteile von MIDI Wird dieses Gerät an ein externes MIDI-System (Computer, Sequencer, Sound-Module usw.) angeschlossen, ergibt sich eine noch bessere Aufnahmequalität. Werden beispielsweise die Vokalstimme und eine Gitarre mit diesem Gerät aufgezeichnet, können diese Parts beim Abmischen mit dem Signal eines über einen Sequencer usw. wiedergegebenen Sound-Moduls synchronisiert werden. Bei dieser Mischmethode reduziert sich die Anzahl der erforderlichen Spuren.
Synchronisation mit einem MIDI-Gerät MIDI-Synchronisation mit dem MIDI-Takt Mit Hilfe des MIDI-Taktes kann dieses Gerät mit einem nicht mit dem MTC (MIDI Time Code) kompatiblen Sequencer usw. synchronisiert werden. Die Verwendung des MIDI-Taktes setzt die Erstellung einer Tempotabelle voraus. 2 Stellen Sie den Sequencer auf externe MIDITaktsynchronisation ein. Die MIDI-Song-Daten können dann wiedergegeben werden. Siehe diesbezüglich auch die Anleitung des Sequencers.
Synchronisation mit einem MIDI-Gerät 3 Drücken Sie ENTER. Die Tempotabellenanzeige erscheint im Display. 11 Stellen Sie mit dem Jog-Knopf 02 ein. 02:---- --- 01:---- --Tempo Tempoänderungsposition Nummer der Tempotabelle (blinkt) 12 Wiederholen Sie die Schritte 3 bis 9, um noch weitere Tempotabellen zu erstellen. Wenn die Tempotabelle vollständig erstellt ist, werden die Einstellungen automatisch nacheinander, beginnend mit der ersten Tempoänderungsposition angezeigt.
Synchronisation mit einem MIDI-Gerät 5 6 Drücken Sie ENTER erneut. Das Feld der Tempoänderungsposition beginnt zu blinken. Tempotabelle 1 kann nur für den ersten Takt erstellt werden. Drehen Sie den Jog-Knopf nach rechts, so daß „Del“ angezeigt wird. 05: Del 100 Blinkt 7 Drücken Sie ENTER. „Deleted“ erscheint im Display; Tempotabelle 5 ist nun gelöscht. Auf gleiche Weise kann auch Tempotabelle 1 gelöscht werden.
Synchronisation mit einem MIDI-Gerät Beispiel eines MIDI-Systems Das folgende Beispiel zeigt ein synchronisiertes MIDISystem, das sowohl MMC als auch MTC verwendet und ein MIDI-Sound-Modul enthält. Anschluß Computer MIDI OUT MIDI-interface MIDI OUT MMCSignal MIDI IN MIDI IN Notendaten usw.
Abmischen Abmischen Abmischen (Grundlagen) Nachdem ein Song mit diesem Gerät aufgezeichnet und gegebenenfalls editiert wurde, kann er mit der gewünschten Pegelbalance und der gewünschten Kanalzuordnung auf einen Master-Recorder (DAToder MD-Recorder) überspielt werden. Aus den vier Spuren dieses Geräts werden zwei Spuren (normales Stereosignal). Dieser Prozeß, der als „Abmischen“ bezeichnet wird und ein ganz wichtiger Teil der Musikproduktion darstellt, wird im folgenden behandelt.
Abmischen Abmischen (fortgeschrittener Betrieb) Verwendung der TRACK-Buchsen Die TRACK 1-4-Buchsen an der Oberseite des Geräts geben die Signale der einzelnen, auf der Disc aufgezeichneten Spuren direkt aus. Diese Buchsen sind vor allem dann nützlich, wenn nur eine beschränkte Anzahl von externen Effector-Geräten zur Verfügung steht. Beispiel: Nachdem die Vokalstimme auf Spur 1 und das Keyboard auf Spur 2 aufgezeichnet ist, tritt folgende Situation ein.
Abmischen 3 Im Mischaufnahmebetrieb werden die Spuren 1 und 2 von Song 1 auf Spur 4 abgemischt. Song 1 7 Song 2 Dr (L) Dr (L) +B+G Dr (R) Dr (R) Song 1 G Im Overdub-Verfahren wird das Keyboard in Stereo auf die Spuren 3 und 4 aufgezeichnet, während das Wiedergabesignal der Spuren 1 und 2 (Song 1) abgehört wird.
Zusatzinformationen Störungsüberprüfungen Meldungen im Display Bevor Sie sich bei einer Störung an einen Fachmann wenden, gehen Sie die folgende Liste durch. Häufig ist die Störung lediglich auf einen Bedienungs-, Einstellungsfehler oder ein nicht korrekt angeschlossenes Kabel zurückzuführen. Das Display zeigt außer Betriebszuständen auch Fehlermeldungen an. Die Meldungen sind im folgenden zusammengestellt. Kein Betrieb möglich / Die Disc ist verschmutzt oder beschädigt. Eine andere Disc verwenden.
Zusatzinformationen Besonderheiten des MDSystems Während kontinuierlicher Wiedergabe schaltet das Gerät zwischen den Songs auf Wiedergabe/Pausen-Funktion Das Gerät schaltet kurzzeitig auf Wiedergabe/Pause, sobald es die Nummer eines neuen Songs oder eines mit Song Divide kreierten Song-Teils erreicht. Das MD-Deck weist die folgenden Besonderheiten auf. Diese sind bei MDs systembedingt es handelt sich nicht um eine Störung.
Zusatzinformationen Return 1-2 (L/R) Typ: Klinke (unsymmetrisch) Eingangsimpedanz: über 20 kOhm Nenneingangspegel: –10 dBs (max.
Zusatzinformationen Glossar TOC (Table of Contents, Inhaltsverzeichnis) Ein vom Musik-Datenbereich getrennter Disc-Bereich für zusätzliche Informationen bezüglich der Disc und der Spuren. Am Ende jeder Aufnahme und jedes Editiervorgangs muß der TOC aktualisiert werden. ATRAC (Adaptive Transform Acoustic Coding) Ein Kompressionsverfahren, mit dessen Hilfe die MD trotz des kleineren Disc-Durchmessers dieselbe Aufnahmezeit besitzt wie eine CD.
Zusatzinformationen Blockdiagramm Die folgende Abbildung zeigt das Blockdiagramm dieses Recorders.
Zusatzinformationen Sony Multi Track Recorder MDM-X4 MIDI-Implementationstabelle Transmitted Function... Recognized Basic Channel Default Changed Mode Default Messages Altered * * * * * * * * * * * * * * True Voice * * * * * * * * * * * * * * Note Number: SEP 21, 1996 Version: 1.