3-990-973-15 (1) Professional Disc Recorder Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference.
Important Safety Instructions • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
If you have questions on the use of the above Power Cord/ Appliance Connector/Plug, please consult a qualified service personnel. Denna etikett finns på ovansidan av driftenheten. When installing the installation space must be secured in consideration of the ventilation and service operation. • Do not block the ventilation slots at the left side and right side panels, and vents of fans. • Leave a space around the unit for ventilation.
For the customers in Europe This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/ EEC) issued by the Commission of the European Community.
Table of Contents Chapter 1 Overview Features............................................................................................ 9 Features of This Unit ............................................................................. 9 Features of the PDBK-101/102/103/104 Option Boards .................... 11 Names and Functions of Parts ..................................................... 12 Front Panel ..........................................................................................
Notes on Handling............................................................................... 40 Write-Protecting Discs ........................................................................ 40 Loading and Unloading a Disc ............................................................ 40 Formatting a Disc ................................................................................ 41 Handling of Discs When Recording Does Not End Normally (Salvage Functions) ...........................................
Sorting Clip Lists................................................................................. 72 Using the PDZ-1 Proxy Browsing Software ................................ 74 Chapter 5 File Operations Overview......................................................................................... 75 Directory Structure .............................................................................. 75 File Operation Restrictions..................................................................
Appendix Important Notes on Operation.................................................... 105 Condensation ..................................................................................... 105 Periodic Maintenance.................................................................. 106 Digital Hours Meter........................................................................... 106 Troubleshooting .......................................................................... 107 Alarms .......................
Chapter 1 Chapter 1 Overview Overview 1) MPEG HD is a trademark of Sony Corporation. Features The PDW-F70 is a professional disc recorder supporting HD playback and recording with Professional Disc 1) media. When you use this unit in combination with a nonlinear editing system, the FAM 2) function enables data file transfers between the unit and computers over the i.LINK interface, allowing the unit to be used like an external hard drive.
Chapter 1 Overview resolution data stream. Whenever this unit records fullresolution MPEG HD data, it simultaneously generates and records low-resolution proxy AV data. Because of its small size, proxy AV data can be transferred quickly over computer networks, easily edited in the field with laptop computers, 1) and readily used in a wide variety of applications, such as content management on small-scale servers.
Other features Variety of remote control units • Infrared remote commander (supplied) • RS-232C 9-pin remote control • RS-422A 9-pin remote control • Minijack 4-pole remote control Color LCD display The unit is equipped with a 16:9, 3.5-inch color LCD which allows you to check the contents of the disc and use the menu system without connecting an external monitor. Features of the PDBK-101/102/103/ 104 Option Boards The following option boards provide expanded functions and interfaces for the unit.
Names and Functions of Parts Front Panel Chapter 1 Overview q; Disc slot and EJECT button 1 On/standby 1 switch and indicator EJECT F1 F2 ACCESS 2 ACCESS indicator qa Infrared sensor F3 NETWORK F4 CHAPTER F5 EXPAND VAR MARK1 MENU LOCAL REMOTE 3 Remote control switch LEVEL SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK IN SET OUT RESET JOG PAGE DISPLAY CH 1 PHONES CH 2 CH 3 CH 4 4 LEVEL knob PREV KEY INHI VARIABLE REC PRESET PB SHIFT TOP MARK2 PLAY F REV NEXT F FWD STOP
Note Do not turn off the POWER switch on the rear panel or disconnect the power cord while the ACCESS indicator is lit. Doing so can result in a loss of data on the disc. d LEVEL (audio level adjustment) knob This adjusts the volume of the audio output from the PHONES jack. At the same time, it also adjusts the volume of the output from the AUDIO MONITOR connector on the rear panel.
1 Display and function menu section 1 Display Chapter 1 Overview F1 F2 2 F1 to F5 buttons F3 F4 F5 PAGE DISPLAY 3 DISPLAY/KEY INH button 4 PAGE button q; Audio level meters 5 Monitor video display section qa Audio format qs Recording/playback format 1 0 0 -12 -12 -20 -20 -30 -40 -60 -30 -40 -60 2 qd Time data type SP VITC 6 Function menu TC MODE PRESET RUN MODE REC RUN 4 3 + 4 4CH 16 BIT MPEG HD qf Time data display section 3 TCG EXT 1080 COOO1 60I INPUT REM:077 M 00:00 .
Note Use the largest size to display the system menu and view superimposed information. For details, see page 81 “Function Menu” in Chapter 6. g Operation modes This displays the current operation modes. KEY INH (key operation inhibit mode): Key operation inhibit mode has been turned on with the KEY INH button.
Chapter 1 Overview r Audio monitor channels This displays the audio monitor channels, as set with MONI CH and MONI SEL on page P1 of the function menu (see page 82). When you are monitoring channels 1 and 2 (MONI CH is set to “CH 1/2”), the display changes as follows, depending on the setting of MONI SEL.
a VAR (variable) button To play back in variable-speed mode using the shuttle dial, press this button, turning it on. 5 Recording/playback control block 1 PREV/TOP button b JOG button To play back in jog mode using the jog dial, press this button, turning it on. d Jog/shuttle transport indicators These show the playback direction in jog, shuttle, or variable-speed mode. b (green): Lights during playback in the reverse direction. B (green): Lights during playback in the forward direction.
disc stop mode. For details, see the explanation of STILL TIMER in the setup menu (page 91). STANDBY button: Press this button to put the unit into standby-off mode (the STOP button lights, and the STANDBY indicator lights). Press it again to return to the original state (STOP button lit, STANDBY indicator off). Chapter 1 Overview e REC (record) button Press this button together with the PLAY button to start recording. Recording starts on the unrecorded part of the disc.
2 Analog audio signal input/output section 3 Digital signal input/output section 1 HDSDI INPUT connector 1 AUDIO INPUT 1/3 and 2/4 connectors 2 HDSDI OUTPUT connectors 3 SDSDI OUTPUT connector HDSDI INPUT HDSDI OUTPUT 1 2 SDSDI OUTPUT AUDIO MONITOR R L AUDIO INPUT 1/3 2/4 Chapter 1 Overview 2 AUDIO OUTPUT 1/3 and 2/4 connectors 3 AUDIO MONITOR connectors AUDIO OUTPUT 1/3 2/4 a AUDIO INPUT (analog audio signal input) 1/3 and 2/4 connectors (XLR 3-pin, female) These connectors input two channels
To handle input signals as non-audio data, use the AUDIO CONTROL >DATA MODE item of the setup menu (see page 93) to set the input of channels 1 and 2 (CH1/CH2 IN) or the input of channels 3 and 4 (CH3/CH4 IN) to “DATA”. Chapter 1 Overview b DIGITAL AUDIO (AES/EBU) OUTPUT 1/2 and 3/4 connectors (BNC type) These output AES/EBU format digital audio signals. The 1/2 connector corresponds to audio channels 1 and 2, and the 3/4 connector corresponds to audio channels 3 and 4.
d Remote connector selector switch Push this switch to the side of the remote control connector you are using, either the RS232C connector or the REMOTE (9P) connector. Notes • If video or audio signals from an external device connected to the S400 connector fail to be output, disconnect the i.LINK cable and connect it again, pushing it straight in. • Before connecting or disconnecting an i.LINK cable between this unit and a device with a 6-pin i.
Press M to perform +5 times normal speed shuttle playback in the forward direction. Using the infrared remote commander Chapter 1 Overview Before use Pull out the insulation sheet. Insulation sheet To replace the lithium battery in the remote commander The remote commander uses a CR2025 Lithium Battery. Do not use a battery other than the CR2025. 1 Hold down the lock lever 1, and then pull out the battery holder 2.
Preparations Chapter This unit is shipped with the system frequency still unset. Therefore, you need to set the system frequency before using the unit. (The unit cannot be used unless the system frequency is set.) Once it is set, the system frequency is retained even when the unit is powered off. To set the system frequency Use the following procedure.
Note Be sure to carry out step 3 before powering the unit off (putting it into standby). The new system frequency setting will not be saved if you power off without carrying out step 3. 4 Press the on/standby switch to power the unit off (put it into standby), and then press it again to power the unit on. Chapter 2 Preparations The selected system frequency becomes available for use. You can change the system frequency setting by using the setup menu item OPERATIONAL FUNCTION >SYSTEM SEL >SYSTEM FREQ.
AUDIO MONITOR REF VIDEO INPUT COMPOSITE OUT AUDIO MONITOR R L PDW-F70 (this unit) COMPOSITE OUT REF VIDEO INPUT TIME CODE IN OUT -AC IN AUDIO MONITOR COMPOSITE OUT AUDIO MONITOR R L -AC IN AUDIO INPUT AUDIO INPUT AUDIO OUTPUT 2/4 1/3 DIGITAL 1/2 AUDIO (AES/EBU) 2/4 3/4 1/3 PB /B 2/4 AUDIO OUTPUT 1/3 DIGITAL 1/2 AUDIO (AES/EBU) 2/4 SYNS HDSDI OUTPUT 1 2 RS232C MONITOR REMOTE(9P) CONTROL SDSDI OUTPUT HDSDI OUTPUT 1 2 RS232C MONITOR S400 REMOTE(9P) CONTROL S400 1 2 2 SDI
• This unit’s S400 connector has 6 pins. Check the number of pins on the i.LINK connector of your notebook computer, and use an appropriate i.LINK cable. See “Using PDZ-1 Proxy Browsing Software” in Chapter 4 (page 74) for more information about installing the PDZ-1 software. See the online help of PDZ-1 for more information about using PDZ-1. Chapter 2 Preparations Some limitations apply to FAM connections. For details, see “File Operations in File Access Mode” in Chapter 5 (page 78).
When using an editing control unit The following figure shows a cut editing system comprising this unit as a player, an HDW-M2000/M2000P unit as a recorder, and a BVE-700A as an editing control unit.
Reference video signal HD video monitor To HDSDI input connector To analog audio input connector 1 1 REF VIDEO INPUT HDSDI OUTPUT COMPOSITE OUT PDW-F70 (this unit, player) AUDIO MONITOR AUDIO MONITOR R L TIME CODE IN OUT -AC IN POWER ANALOG HD INPUT Y/G PB /R Chapter 2 Preparations AUDIO INPUT 1/3 2/4 AUDIO OUTPUT 1/3 DIGITAL 1/2 AUDIO (AES/EBU) 2/4 3/4 PB /B SYNS INPUT 1/2 HDSDI OUTPUT 1 2 SDSDI OUTPUT RS232C MONITOR REMOTE(9P) CONTROL REF VIDEO INPUT Remote connector HDSDI OU
SD video monitor Editing Control Unit Settings To composite video input connector When connecting an editing control unit to use with this unit, make the following settings. To analog audio input connector BVE-700/700A 2 1 Set VTR constants as follows.
XLR cable External Synchronization Ferrite core (supplied) This unit synchronizes as shown in the following table, according to the presence or absence of signals input to the HDSDI INPUT connector, the presence or absence of signals input to the REF VIDEO INPUT connector, and the setting of the V INPUT item on the HOME page of the function menu (see page 81).
DATE/TIME PRESET Setup YEAR MONTH DAY TIME TIME ZONE The principal setup operations before operating this unit are carried out using setup menus. This section explains how to set the date and time and how to adjust the brightness of the LCD panel. INC/DEC SHIFT DATE SAVE TO MENU JOG DIAL ( )( )KEY SET KEY MENU KEY This screen allows you to set the following items.
1 Use the arrow buttons (M/MARK1, m/MARK2) or jog dial. 5 2,3,4,5 To return the settings to the factory defaults Press the RESET button. EJECT 0 -12 -20 -30 -40 -60 ACCESS 1 -30 -40 -60 2 MPEG HD LOCAL LEVEL PHONES 3 SP VITC 1080 60I COOO1 CH 2 F2 RUN MODE REC RUN F3 3 + 4 TC/VITC VITC F4 CHAPTER DF/NDF NDF F5 EXPAND 00: 00.
SETUP MENU OPERATIONAL FUNCTION DISPLAY CONTROL TIME CODE DISC PROTECTION VIDEO CONTROL AUDIO CONTROL INTERFACE SELECT METADATA SETUP BANK OPERATION 24P (23.98P) Mode Settings Selecting the Playback Mode (23.98PsF or 2-3 Pulldown) ENHAN MENU GRADE 1 9 The second level of the OPERATIONAL FUNCTION menu appears. Press the MENU button. The system menu (see page 83) appears. 2 Press the M/MARK1 or m/MARK2 button to select SETUP MENU. 3 Press the ,/OUT button.
SETUP MENU OPERATIONAL FUNCTION SYSTEM SEL SYSTEM FREQ : 601 * 60I 50I 30P 25P 23.98P Input and Output Signals in 24P (23.98P) Mode The following tables show the signals input and output by the unit when “23.98PsF” and “2-3 PULL DOWN” are selected. Input and output signals Chapter 2 Preparations 14 Press the m/MARK2 button to select “23.98P”. 15 If you want to change the monitor output setting as well, press the
Timecode display Recording timecode Type 23.98PsF LTC display 24-frame timecode PDT display – When you preset timecode manually, select a multiple of 4 as the number of frames in the timecode, and adjust so that the preset timing begins with an “A-frame”. The unit will then adjust so that the timecode at the start of recorded clips will have a number of frames that is a multiple of 4.
The values of “24F TC” and “30F TC” under TIME CODE >PD PRESET in the setup menu are used as the conversion references. SETUP MENU DISPLAY CONTROL :T&STA DISPLAY INFO * TIME DATA & STATUS TIME DATA & UB TIME DATA & CNT TIME DATA & TIME TIME DATA & CLIP TIME DATA ONLY To display 30-frame pulldown timecode in the monitor video display section or on an external monitor 1 Press the MENU button. The system menu (see page 83) appears.
a) Only when the system frequency is 60I/30P. Superimposed Text Information To turn superimposed text on and off Set the CHAR SEL item on page P1 of the function menu. ON: Display superimposed text. OFF: Do not display superimposed text. LCD: Display superimposed text on the LCD panel of this unit, but do not display it on an external video monitor connected to this unit.
Display B1 B2 Display Description The current menu settings are the same as the settings in menu bank 1. The current menu settings are the same as the settings in menu bank 2. Operation mode Block A Block B SHUTTLE STILL A still picture in shuttle mode SHUTTLE (Speed) Shuttle mode (Speed) Variable speed mode Chapter 2 Preparations B3 The current menu settings are the same as the settings in menu bank 3. VAR DF The current menu settings are the same as the factory defaults.
Meaning INT REGEN-T&U The internal timecode generator is in synchronization with the playback timecode (LTC) read from disc. EXT LTC-T&U The internal timecode generator is in synchronization with the external timecode (LTC) input to the unit and is generating the same timecode values and user bit values as those of the external timecode (regeneration).
Recording and Playback Chapter 3 Recording and Playback Handling Discs Chapter 3 • Do not leave cartridges where dust may get inside. • Store cartridges in their cases. Discs Used for Recording and Playback Care of the discs • Remove dust and dirt on the outside of a cartridge using a soft dry cloth. • If condensation forms, allow ample time to dry before use. This unit uses the following disc for recording and playback: PFD23 Professional Disc 1) (capacity 23.
On/standby switch and indicator To unload Press the EJECT button. 3 Select “DISC MENU” using the M/MARK1 button or m/MARK2 button, then press the ,/OUT button. 4 Select “FORMAT” using the m/MARK2 button, then press the ,/OUT button. The menu item QUICK FORMAT is selected. 5 Press the ,/OUT button. The message “QUICK FORMAT OK?” appears. To cancel a disc format Press the RESET button to return to the state of step 3. To clear the menu from the screen, carry out step 7. The format starts.
Full salvage: Clips are reconstructed on the basis of markers recorded on the disc. Nonvolatile memory cannot be used, so processing takes longer than for a quick salvage (about 30 seconds, although it depends on the state of the disc). You are prompted to execute a full salvage whenever you insert a disc that was removed manually from a powered off device after interruption of recording by power off.
Recording This section describes video and audio recording on the unit. See page 81 “Function Menu” in Chapter 6 for more information about function menu operations. See page 96 “Setup Menu Operations” in Chapter 6 for more information about setup menu operations. Note Make the following settings and adjustments before starting to record. Recording format settings: See the next section “To set the video and audio recording formats”.
To record timecode after setting an initial value (Internal Preset) 6 Press the SET button. The message “NOW SAVING...” appears, and the timecode set in step 5 is displayed. If RUN MODE on page P2 of the function menu is set to “FREE RUN”, timecode begins to advance from the initial value you just set. To set an initial value 1 2 3,5 5 4,5 To set timecode to the current time EJECT F1 1 Set RUN MODE on page P2 of the function menu to “FREE RUN”, and set DF/NDF to “DF”.
To cancel the user bits setting Press the MENU button. 4 Press the SET button. The message “NOW SAVING...” appears, and the user bits set in step 3 are displayed.
by specifying a number of seconds after the first frame. The selection range is 0 seconds (0 SEC) to 10 seconds (10 SEC).
Playback This section describes playback of video and audio on the unit.
To carry out playback again, move back to the desired clip using the PREV button, jog dial or shuttle dial. EJECT F1 F2 ACCESS F3 To set shot marks While playing back a disc, you can set essence marks such as SHOT MARK1 and SHOT MARK2 in desired frames. To set a SHOT MARK1 or SHOT MARK2, hold down the M/MARK1 or m/MARK2 button and press the SET button. Note To erase or change essence marks, use the supplied PDZ-1 Proxy Browsing Software.
Playback in variable-speed mode starts. 3 To stop playback in variable-speed mode, return the shuttle dial to the center position, or press the STOP button. In any of the following screens, you can press the THUMBNAIL button to return to the original screen.
2 Press the M/MARK1 button or m/MARK2 button to select CLIP INFORMATION. 3 Press the SET button. A list of CLIP INFORMATION items appears. DATE: Date and time of recording TIME CODE: Timecode of the first frame in the clip DURATION: Recording time SEQUENCE NUMBER: Thumbnail sequence number See “To select a thumbnail image and start playback” (page 49) for more information about sequence thumbnail numbers.
Searching for Frames With Essence Marks Proceed as follows. 1 Note The maximum number of blocks may be larger than 1728 when the recorded duration of the clip is short. In this case, the frame interval of expanded thumbnails is fixed at 1 frame. This allows you to view expanded thumbnails at equal intervals.
Indicates that this is a list of frames containing the essence Sixth frame is selected from a mark (SHOT MARK1) total of 36 SHOT MARK1 frames 2 The CHAPTER screen appears, showing thumbnails of the frames where the shot marks are set. “S1” and “S2” marks on thumbnails indicate frames where SHOT MARK1 and SHOT MARK2 marks are set. Thumbnails without a mark are frames where REC START marks are set.
Sixth frame is selected from a total of 34 sub clips Name of current clip list a) Sub clip information (date and time of creation, initial timecode, playback time) Clip List Playback You can play back clips in the same order as in a clip list created using the scene selection function. See Chapter 4 for more information about scene selection. Playing back in clip list order Proceed as follows. If the clip list that you want to play exists on the disc, load it into the current clip list.
2 3 To perform repeat playback for clip list playback, load a clip list into the current clip list and then press the SUB CLIP button. Press the PLAY button. Playback starts from the saved playback position. Normal playback: When playback of the last clip finishes, it resumes from the start of the disc, repeatedly playing from the first through the last clip on the disc.
You return to the thumbnail screen, and a lock icon appears on the thumbnail of the selected clip to show that it is locked. Lock icon Locked clips cannot be deleted or set the thumbnail image (index picture) and so on. Unlock the clip if you want to perform any of these operations. • Clips cannot be deleted when the Write Inhibit tab of the disc is set to the recording disabled position, or when “REC INH” on page P1 of the function menu is set to “ON”. • Locked clips cannot be deleted.
1 With the SUB CLIP button off, press the THUMBNAIL button, turning it on. Thumbnails of the clips on the disc appear. 2 Press the MENU button. The CLIP menu appears. 3 To cancel the deletion and return to the CLIP MENU Select “CANCEL”, and then press the SET button. Press the RESET or MENU button. Chapter 3 Recording and Playback 5 A sub menu appears. Use the V/MARK1 button to select “OK”, and then press the SET button. The clip is deleted and you return to the thumbnail screen.
Scene Selection Chapter 4 Overview What is scene selection? Chapter 4 Scene Selection Scene selection is a function which allows you to select material (clips) from the material recorded on a disc and perform cut editing. You can do this by operating on this unit only. • Scene selection is a convenient way to perform cut editing in the field and in other offline situations. • With the scene selection function, you create clip lists (edit data).
Flow of scene selection editing Disc Record material or insert disc containing recorded material into this unit EJECT F1 F2 ACCESS F3 NETWORK F4 CHAPTER F5 EXPAND VAR MARK1 MENU LOCAL REMOTE LEVEL SUB CLIP THUMB NAIL IN SET OUT RESET JOG PAGE DISPLAY CLIP MENU PHONES CH 1 CH 2 CH 3 CH 4 KEY INHI VARIABLE REC PRESET PB SHIFT ESSENCE MARK PREV TOP MARK2 PLAY F REV NEXT F FWD END STOP REC SHUTTLE STANDBY PDW-F70 PDW-F330/F350 To edit a clip list on the disc Load a cli
Clips Sub clips (clips in clip lists) Material recorded with this unit is managed in units called “clips”. A clip contains the material between a recording start point and a recording end point. Clips have numbers beginning with C, for example C0001. The specified clips (or parts of clips) in a clip list are called “sub clips”. Sub clips are virtual data specifying ranges in the original clips. Clip data in the original clips is not overwritten.
Assigning Clip Titles CLIP AUTO TITLING When the setup menu item OPERATIONAL FUNCTION >CLIP TITLE >AUTO TITLE (see page 87) is set to “ENABLE”, titles are displayed instead of clip numbers for all clips recorded after the setting is made.
To assign clip names on this unit The title assigned to clip becomes its clip name (file name). C0001.MXF TITLE00001 When sub item “AUTO NAMING” is set to “C****” Note When the first letter of the title setting on the CLIP TITLE menu is a space or period (.), the clip name is the title string minus the first letter. To enable clip and clip list renaming by FAM Carry out step 2 “To assign clip names on this unit”.
Sequences of multiple s characters is converted into single s characters. The following alphabetic symbols can be displayed. :.?!#*/()+-&@ =<>%";_ Display example JumpingDolphin_No103 r JUMPINGDOsNO103 Creating Clip Lists Select the desired clip, to include it in the current clip list as a sub clip. There are two ways to select clips. • Select from the thumbnail screen. You can select the desired clips from the thumbnail screen. You can also select continuous clips at a time.
+NAME: Name of the clip list, or a user-defined name You can use the supplied PDZ-1 Proxy Browsing Software to assign titles to clip lists. 4 Use the M/MARK1 or m/MARK2 button to select a clip list number such as E0001, and then press the SET button. This returns to the thumbnail screen. 2 5 Press the MENU button. The clip list window appears. If you selected NEW FILE in step 4, the display shows the state with no clips loaded as shown below. Select NEW FILE to create a new clip list.
8 Use the arrow buttons or jog dial to select the desired clip. Total duration of sub clips in the current clip list You can also select clips with the following operations. Press the PREV or NEXT button: Moves to the previous or next clip. Press the PREV or NEXT button with the SHIFT button held down: Moves to the first or last clip. Press the M/MARK1 or m/MARK2 button with the SHIFT button held down: Switches to the previous or next page. Does not switch when there is only one page.
Note Even if you select several thumbnails, they are added to the clip list as one continuous sub clip. To add sub clips using the chapter function The chapter function allows a thumbnail to be displayed for each shot mark recorded within a clip. Asterisk appears when clip list has not been saved to disc. • Even when a clip whose thumbnail is not the first frame is added to a clip list, the thumbnail displayed in the clip list is always the first frame as a thumbnail.
To reset an In point or Out point With the
You can also select clips with the following operations. Press the PREV or NEXT button: Moves to the previous or next clip. Press the PREV or NEXT button with the SHIFT button held down: Moves to the first or last clip. Press M/MARK1 or m/MARK2 button with the SHIFT button held down: Switches to the previous or next page. Does not switch when there is only one page. Press an
previous or next page. Does not switch when there is only one page. Indicates that 2nd sub clip will be moved to position of 7th sub clip. I-shaped cursor showing position to which selected sub clip will be moved. Chapter 4 Scene Selection To return to the clip list window without moving any sub clip Press the RESET button. 3 To cancel the trim and return to the previous screen Press the m/MARK2 button to display “OK” (the background color changes into yellow), and press the RESET button.
The CLIP MENU appears after the trim is executed. If you press the SHIFT + SET buttons instead of the SET button, you return to the state after step 4 in “Basic Operations”, allowing you execute another trim. 6 By default, the start timecode (LTC) for the current clip list is set to “00:00:00:00”. To set this to a different value, proceed as follows. 1 Save the current clip list to disc. Carry out steps 1 to 4 of the procedure in “Basic Operations” (see page 67) (select TC PRESET in step 2).
However, if you press the SUB CLIP button to turn it off, and then press it again to light it, the playback start position is reset to the start of the clip list. With the SUB CLIP button lit, press the PLAY button. You can repeat playback of the current clip list by setting SET UP >OPERATIONAL FUNCTION >REPEAT MODE to ON. Saving the Current Clip List to Disc Notes • Edited clip list data is not saved unless you carry out this operation.
Use the supplied PDZ-1 Proxy Browsing Software. For details, see the PDZ-1 online help. Managing Clip Lists After you create or edit a clip list, you can use the CLIP menu to save it to disc, load it from disc into unit memory, and delete it from the disc. Displaying the CLIP menu Hold down the SHIFT button and press the SUB CLIP button. In the thumbnail list screen and the clip list screen, you can display the CLIP menu by pressing the MENU button.
Note 3 The CLIP menu can handle up to 99 clip lists. Changing Displayed Items of Information on Sub Clips You can change information displayed in the lower portion of each thumbnail in the clip list window. Proceed as follows. 1 Display the CLIP menu. See “Displaying the CLIP menu” (page 71). 2 Use the M/MARK1 or m/MARK2 button to select “CLIP INFORMATION”, and then press the SET button. Chapter 4 Scene Selection A screen appears allowing you to select information items to display.
See “Displaying the CLIP menu” (page 71). 2 You can jump to the first clip or last clip by pressing the PREV or NEXT button with the SHIFT button held down. Use the M/MARK1 or m/MARK2 button to select “SORT CLIP LISTS BY...”, and then press the SET button. A screen like the one shown below appears. 3 Use the M/MARK1 or m/MARK2 button to select the type of sorting. Chapter 4 Scene Selection NAME: Sort in ascending order by clip list name. DATE: Sort by date of creation, with the newest clip list first.
Using the PDZ-1 Proxy Browsing Software When a computer with the PDZ-1 Proxy Browsing Software installed is connected to this unit, you can transfer the proxy AV data and metadata files recorded on a disc to the computer. On the computer side, PDZ-1 enables you to browse the proxy AV data, add or modify metadata (titles, comments, essence marks, etc.), or create a clip list. The modified metadata and the created clip list can then be written back to the disc loaded in this unit.
File Operations Chapter 5 Overview root a) A remote computer can be connected to this unit and used to operate on recorded data which has been saved in data files, such as video and audio data files. Use FAM (file access mode) for the computer connection. INDEX.XML ALIAS.XML b) DISCMETA.XML MEDIAPRO.XML Directory Structure Clip Chapter 5 File Operations C0001.MXF The following figure shows the directory structure of discs visible to a remote computer. C0001M01.XML C0002.MXF Note C0002M01.
File Operation Restrictions This section explains which operations are possible on files stored in each directory. When required, the following operation tables distinguish reading and writing from partial reading and writing. Read: Read data sequentially from the start to the end of the file. Partial read: Read only a part of the data in the file. Write: Write data sequentially from the start to the end of the file. Partial write: Write data to a part of the file only.
Notes • Directories cannot be created in the Clip directory. • When the following operations, supported by version 1.5 and higher XDCAM devices, are carried out on a disc, then it becomes impossible for version 1.4 and lower XDCAM devices to record new clips or delete existing clips on that disc. (The only possible operations are playback and disc formatting.) - Writing of clips with user-defined names - Deletion of clips (except the last recorded clip) - Locking of clips • If you attempt to write a C*.
a) UTF-8 file names can be up to 63 bytes in length. (Depending on the character type, file names (including extension) may be limited to 21 characters.) b) Only when the Write Inhibit tab on the disc is set to enable recording and “REC INH” is set to “OFF”. The following directory operations are possible in the General directory.
File data Transfer of files Disc recorder (this unit) Laptop computer, etc. F2 F3 NETWORK VCR MARK1 MENU F4 To exit file operations Proceed as follows. F1 ACCESS To eject discs from a remote computer Right click the icon representing this unit in Explorer, and select “Eject” from the menu which appears.
To disable FAM connections Execute one of the procedures described in the previous section “To make a reconnection” to make a FAM connection between this unit and the remote computer. To disable FAM connections, in the setup menu, set INTERFACE SELECT >i.LINK MODE to “AV/C” (see page 94).
Menus Chapter 6 To clear the function menu from the screen Press the DISPLAY button. The size of the monitor video section increases. Function Menu The function menu provides access to frequently used settings, such as input video signal selection and timecode settings. Menu settings are stored in nonvolatile memory and are preserved even after the unit is powered off. To change the setting of a function menu item Use the F1 to F5 buttons.
Setting item Description Setting item F3: A2 INPUT (audio input 2) F5: A4 INPUT (audio input 4) Selects the audio input signals assigned to audio channels 2 and 4.
Setting item Description F2: TC MODE (timecode mode) When TCG is set to “INT” Selects whether the count value advances from a preset initial value, or advances consecutively from the timecode of the last frame recorded on the disc. PRESET: Advance from a preset initial value. REGEN (regenerate): Advance consecutively from the timecode of the last frame recorded on the disc.
2 Press the M/MARK1 or m/MARK2 button to select SETUP MENU or DISC MENU. 3 Press the ,/OUT button. The setup menu (see page 86) or the disc menu (see page 98) appears. Setup Menu As shown in the following figure, the setup menu has three levels. The top level shows a general classification of the setting items in the menu. Except for MENU GRADE, the actual setting items are found on the second or third level.
Top level SETUP MENU OPERATIONAL FUNCTION Second level Third level REPEAT MODE AUTO EE SELECT LOCAL ENABLE REC FORMAT DISC END DISC OUT F. FWD/REW STOP STANDBY OFF CLIP TITLE AUTO TITLE TITLE FILE NAMING NAMING FORM AUTO NAMING SYSTEM SEL SYSTEM FREQ UC/J 23.9P OUTPUT SEARCH ENABLE VAR SPD LIMIT PREROLL TIME AFTER CUE-UP ASM POSTROLL CHARA. POSITION CHARA. TYPE CHARA. VSIZE DISPLAY INFO SUB STATUS MENU DISPLAY BRIGHTNESS ALARM MENU STATUS HD CHARA TIME CODE TCG REGEN UB BINARY GP.
Top level AUDIO CONTROL Second level REC MODE DATA MODE LEVEL SELECT INT AUDIO SG SHUTTLE MUTING EDIT POINT DV OUT MODE INTERFACE SELECT D-SUB OUTPUT AUDIO OUTPUT REMOTE I/F BAUDRATE i.
OPERATIONAL FUNCTION [Operational]: Operation settings Description AUTO EE SELECT [> Auto DISC OUT [>> DISC OUT]: EE]: Determine whether When no disc is loaded. the unit enters E-E mode or PB mode when audio F.FWD/REV [>> F.FWD/ and video signals from REV]: Operations when other equipment are input. in fast forward or rewind mode *EE [>>> EE]: Output video and audio signals received from other equipment. PB [>>> PB]: Suppress video and audio signals.
Chapter 6 Menus 88 OPERATIONAL FUNCTION [Operational]: Operation settings Description SEARCH ENABLE [> Search ENA]: Specify how to put the unit into a search mode (jog, shuttle, or variable-speed). *DIAL DIRECT [>> DIAL]: The unit switches to a search mode when you press the JOG, SHUTTLE, or VAR button, or when you turn the jog or shuttle dial (except during recording). VIA SEARCH KEY [>> via KEY]: The unit switches to a search mode when you press the JOG, SHUTTLE, or VAR button.
DISPLAY CONTROL [Display]: Settings related to display on the LCD panel of this unit and on an external monitor Description DISPLAY INFO [> DISP info]: Select the content of the character information shown in the monitor video section and on an external monitor. *TIME DATA & STATUS [>> Time&STA]: Time data and the operating mode of the unit TIME DATA & UB [>> Time&UB]: Time data and user bits data.
TIME CODE [Time Code]: Settings related to the timecode Description generator TCG REGEN [> TCG regen]: Select the signals to generate when the timecode generator is set to regenerate mode (TC MODE on page P2 of the function menu is set to “REGEN”). *TC & UB [>> TC & UB]: Regenerate both timecode signals and user bits signals. TC [>> TC] :Regenerate timecode signals only. UB [>> UB]: Regenerate user bits signals only.
DISC PROTECTION [Disc protct]: Settings related to disc protection Description STILL TIMER [>> STL timer]: Specify the length of time the unit can be in still image mode before switching to disc protection mode. 0.5SEC [>>> 0.5 sec] to 30MIN [>>> 30 min]: Select time from 16 settings ranging from 0.5 second to 30 minutes.
VIDEO CONTROL [Video]: Settings related to video control Description PROCESS CONTROL VIDEO GAIN [>> V gain]: [> Proc ctrl]: Separate Adjust the video output adjustment screens level. appear for the following CHROMA GAIN [>> C gain]: items. Use the jog dial to Adjust the chroma output make settings, and press level the MENU button to return from the adjustment CHROMA PHASE [>> C screens to the second phase]: Adjust the level of the setup menu. chroma phase.
AUDIO CONTROL [Audio]: Settings related to audio control Description REC MODE [> REC mode]: Select the audio recording mode. *4ch×16bit [>> 4ch/16bit]: 4-channel, 48-kHz mode 2ch×16bit [>> 2ch/16bit]: 2-channel, 48-kHz mode DATA MODE [> Data mode]: CH1/CH2 IN [>> CH1/CH2]: Specify whether to handle Specify for the input to digital audio signals as the DIGITAL AUDIO non-audio signals during (AES/EBU) 1/2 recording. connectors. *AUDIO [>>> Audio]: Handle as audio signals.
INTERFACE SELECT [Interface]: Settings related to interfaces Description AUDIO OUTPUT [> Audio Out]: Select the channels for audio *CH1/CH2 [>> CH1/CH2]: Output channel 1 to the AUDIO output from the AUDIO OUTPUT 1/3 and 2/4 connectors. OUTPUT 1/3 connector and channel 2 to the AUDIO OUTPUT 2/4 connector. CH3/CH4 [>> CH3/CH4]: Output channel 3 to the AUDIO OUTPUT 1/3 connector and channel 4 to the AUDIO OUTPUT 2/4 connector.
METADATA [Metadata]: Metadata settings ESSENCE MARK [> EssnceMk] Description SDI OUT [>> SDI out]: Select *ON [>>> ON]: Output. whether to output OFF [>>> OFF]: Do not output. essence marks in the VANC of HD/SDSDI output. SD VANC LINE [>> SDI line]: When SDI OUT is set to “ON”, select the line of SDSDI output in which to output essence marks. 12LINE [>>> 12 line] to 19LINE [>>> 19 line]: Select in the range line 12 to line 19.
MENU GRADE [Menu grade]: Selection of menu items to be displayed Description Determine whether to display basic items only or both basic *BASIC [>> Basic]: Display basic items only. and enhanced items in the monitor video section and the time ENHANCED [>> Enhanced]: Display both basic and data display section when using the setup menu. enhanced items. Setup Menu Operations SETUP MENU OPERATIONAL FUNCTION DISPLAY CONTROL SETUP BANK OPERATION This section explains how to change menu settings.
SETUP MENU DISPLAY CONTROL :ON CHARA.DISPLAY CHARA.POSITION :WHITE CHARA.TYPE :x1 CHARA.VSIZE :T&STA DISPLAY INFO :OFF SUB STATUS :WHITE MENU DISPLAY :55% BRIGHTNESS :ON ALARM 4 Press the ,/OUT button. This displays all possible settings for the item selected in step 3. SETUP MENU DISPLAY CONTROL :OFF SUB STATUS * OFF TC MODE REMAIN CLIP NAME 5 Notes • If you power off the unit before a save operation is completed, settings may be lost. Wait until the save is completed before powering off the unit.
With this done, when you press the MENU button and the ,/OUT button to display the setup menu, all basic and enhanced items on menu level 1 appear. SETUP MENU OPERATIONAL FUNCTION DISPLAY CONTROL TIME CODE DISC PROTECTION VIDEO CONTROL AUDIO CONTROL INTERFACE SELECT METADATA SETUP BANK OPERATION MENU GRADE The setting returned to its factory default is saved in memory as the current setting. To return all settings to their factory default settings 1 Display the setup menu. 2 Press the RESET button.
DISC MENU DISC STATUS STATUS DELETE FORMAT USER ID: TITLE : REMAIN REWRITE SALVAGE FILE SYSTEM : 029 min : 0002 times : OK : OK TO MENU : If you selected CLIP, the status of the current clip appears. The disc menu contains the following items. Characters and symbols inside the brackets [ ] appear in the time data display section. CLIP STATUS STATUS [Status] Displays disc or clip status. DISC [> Disc]: Displays the DISC STATUS screen. CLIP [> Clip]: Displays the CLIP STATUS screen.
Press the MENU button. To clear the menu from the screen Press the MENU button twice. To delete all clips Note Carrying out the following procedure deletes all clips that are not locked. Proceed as follows. 1 Display the disc menu (see page 83). 2 Press the M/MARK1 button or the m/MARK2 button to select DELETE. 3 Press the ,/OUT button. 4 Select ALL CLIP, then press the ,/OUT button. 5 When the message “ALL DELETE OK?” appears, press the SET button. All of the clips on the disc are deleted.
Using Option Boards Option Boards for Enhanced Functionality You can enhance the functionality of this unit by installing option boards in the option slots. You can install up to two option boards. The boards which may be installed in each slot differ, as follows. Slot 1: PDBK-101 Slot 2: One board from among the PDBK-102, PDBK103, and PDBK-104 Warning Improper installation of option boards can result in fire, electric shock, bodily injury, and damage to equipment in the vicinity.
Using the PDBK-102 MPEG-TS Input/Output Board Laptop computer With the PDBK-102 MPEG-TS Input/Output Board installed in option slot 2 of this unit, you can make i.LINK connections between this unit and video devices complying with the HDV 1080i 1) standard (called “HDV devices” below), and between this unit and computers to which HDV devices may be connected. These connections can be used for input and output of MPEG-2 TS streams.
• The PDBK-103 and PDBK-104 cannot be used when the PDBK-102 is installed. Using the PDBK-103 Analog HD Input Board With the PDBK-103 Analog HD Input Board installed in option slot 2 of this unit, you can record HD analog signals such as YPbPr signals and RGB signals in addition to HDSDI signals.
Using the PDBK-104 SD Input Upconverter Board With the PDBK-104 SD Input Upconverter Board installed in option slot 2 of this unit, you can record upconverted SDSDI and composite signals in addition to HDSDI signals.
Appendix Important Notes on Operation Use and storage Do not subject the unit to severe shocks The internal mechanism may be damaged or the body warped. Do not cover the unit while operating Doing so will cause temperatures to rise inside the unit, possibly resulting in failure. After use Turn off the on/standby switch. If you plan not to use the unit for a long time, turn off the POWER switch on the rear panel as well. Shipping • Remove the disc before transporting the unit.
If it appears, wait until it disappears before inserting a disc. Periodic Maintenance Digital Hours Meter The digital hours meter can provide information about the operational history of the unit. Use the information as a guide in scheduling periodic maintenance. For periodic maintenance, contact your Sony dealer. To display digital hours meter The digital hours meter appears in both the monitor video section and time data display section as the digital hours meter menu of the system menu.
Item name (name between Description [ ] is name in the time data display section) H3: SEEK RUNNING[Seek] This shows the cumulative seek operation time for optical head in units of hours. H4: SPINDLE RUNNING[Spdl] This shows the cumulative spindle rotation time in units of hours. H5: LOADING COUNTER[Load] Display the total number of times discs have been loaded in the unit. To exit from the digital hours meter Press the MENU button.
When a disc is inserted Alarm message in time data display section Alarm message in monitor video section Description/action Unknown FS! UNKNOWN FILE SYSTEM. PLEASE FORMAT DISC OR EJECT. Format the disc, or eject it (see page 41). No FS! NO FILE SYSTEM.PLEASE EJECT DISC. Eject the disc. ILL. Disc! IRREGULAR DISC IS USED. USE PROFESSIONAL DISC. Salvage NG! CLIP SALVAGE WAS NOT COMPLETED. See “Handling of Discs When Recording Does Not End Normally (Salvage Functions)” (page 41).
Alarm message in time data display section Alarm message in monitor video section Description/action Disc Top! a) DISC TOP. This appears if you press the PREV button or conduct a high-speed reverse search when the unit is stopped at the start of the disc. Use forward search or playback instead. Disc End! a) DISC END. This appears if you press the NEXT button or conduct a forward high-speed search when the unit is stopped at the end of the disc. Use reverse search or playback instead.
Alarm message in time data display section Alarm message in monitor video section Description/action No SUB CLIP a) CLIP LIST CANNOT LOCATE SPECIFIED This appears when a playback button is pressed with SUB CLIP(S). no sub clips in the current clip list. Playback is not possible when there are no sub clips in the current clip list. SB CLP mode b) TO ADD AN ESSENCE MARK, EXIT FROM SUB CLIP MODE FIRST. This appears when you press the ESSENCE MARK (SHIFT + THUMBNAIL) button with the SUB CLIP button lit.
Alarm message in time data display section Alarm message in monitor video section Description/action HD 60I/30P a) DISC CANNOT BE RECORDED. HD 60I or HD 30P CLIP(S) EXIST. HD 50I/25P a) DISC CANNOT BE RECORDED. HD 50I or HD 25P CLIP(S) EXIST. This appears when the system frequency of this unit does not match that of the loaded disc. Insert a disc that matches the system frequency, or change this unit's system frequency setting (see page 23). HD 23P Disc a) DISC CANNOT BE RECORDED. HD 23.
During playback Alarm message in time data display section Alarm message in monitor video section Description/action 525/60 Disc a) DISC CANNOT BE PLAYED BACK. USE DISC WITH HD 50I or HD 25P RECORDING. This appears when the system frequency of this unit does not match that of the loaded disc. Insert a disc that matches the system frequency, or change this unit’s system frequency setting (see page 23). DISC CANNOT BE PLAYED BACK. USE DISC WITH HD 23.98P RECORDING. DISC CANNOT BE PLAYED BACK.
During thumbnail search, scene selection, and clip list operations Description/action CANNOT EXPAND CLIP ANY FURTHER. The clip cannot be expanded into more blocks. This appears when the EXPAND button is pressed when the number of block is maximum, or when the duration of an expanded thumbnail is 1 frame. SELECTED ESSENCE MARK DOES NOT EXIST. The selected essence mark does not exist. This appears in the essence mark selection screen when the specified essence mark does not exist on the disc.
Alarm message in time data display section Alarm message in monitor video section Action EMPHASIS! a) INPUT AUDIO EMPHASIS IS NOT SUPPORTED. CHECK THE EMPHASIS OF THE AUDIO INPUT SIGNAL. Check the emphasis of the audio input signal. a) Displayed only when DISPLAY CONTROL >ALARM is set to “ON”. Alarms relating to sensors and drives Alarm message in time data display section Alarm message in monitor video section Description/action FAN Stopped FAN MOTOR STOPPED. Contact your Sony dealer.
The unit can be connected to one device with the i.LINK cable (DV cable). When you connect with a device that has two or more i.LINK connectors, refer to the operating instructions supplied with the connected device. About data transfer speed of i.LINK i.LINK defines maximum data transfer speeds of approximately 100, 200 and 400 Mbps 1) that are referred to as S100, S200 and S400 respectively. The maximum data transfer speed that an i.
Playback format Video MPEG HD: HQ35/SP25/LP18 Mbps DVCAM: 25 Mbps Proxy video MPEG-4 1) Audio MPEG HD: 16 bits/48 kHz, 4/2 channels DVCAM: 16 bits/48 kHz, 4 channels Proxy audio A-law 8 bits, 8 kHz, 4 channels 1) The MPEG-4 Codec is a product of Ingenient Technologies, Inc. Recording/Playback time (when PFD23 is used) MPEG HD Mode 4-channel audio 2-channel audio HQ mode (VBR 35 65 minutes or Mbps) more 68 minutes or more SP mode (CBR 25 Approx. 85 Mbps) minutes Approx.
Phono jack (×1), 1.0 Vp-p, 75 Ω, sync negative MONITOR OUT D-sub 15-pin (RGB or YPbPr) Analog audio outputs AUDIO OUTPUT 1/3, 2/4 XLR 3-pin, male (×2), +4/0/–3/–6 dBu (selectable), 600 Ω, balanced AUDIO MONITOR Phono jack (×2) –∞ to +1 dBu/ 47 kΩ/unbalanced (L, R, L+R) PHONES Stereo phone jack (×1), –∞ to –14 dBu, 8 Ω, unbalanced Digital audio outputs DIGITAL AUDIO (AES/EBU) OUTPUT BNC type (×2), 1/2 ch, 3/4 ch complying with AES-3id-1995 Timecode output TIME CODE OUT BNC type (×1), SMPTE timecode, 2.
Using UMID Data Metadata is additional information recorded on discs along with audio-visual data. It is used to bring greater efficiency to the flow of operations from material acquisition through editing, and to make it easier to find and reuse material. As one of application of metadata, the UMID has been internationally standardized. What is a UMID? A UMID (Unique Material Identifier) is a unique identifier for audio-visual material defined by the SMPTE 330M2003 standard.
• Distinguishing between original material and copied material. 00 is added to the Instance Number for original material. • Recording with UTC time. UTC (coordinated universal time) is used when recording the UMID. Use of a universal time system enables uniform management of source material recorded all over the world. • Calculation of date differences. Source material is recorded using modified Julian dates (MJD), which enables easy calculation of date differences between different source material items.
MPEG-4 Visual Patent Portfolio License This product is licensed under the MPEG-4 Visual Patent Portfolio License for the personal and non-commercial use of a consumer for (i) encoding video in compliance with the MPEG-4 Visual Standard (“MPEG-4 Video”) and/or (ii) decoding MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed by MPEG LA to provide MPEG-4 Video.
Glossary AES/EBU A standard established jointly by the AES (Audio Engineering Society) and EBU (European Broadcasting Union) for serial transmission of digital audio. Two channels of audio can be transmitted via a single connector. Clip A recording unit. Clips are created every time recording starts and stops. Clip list A list of locations in the material recorded on the disc, arranged in any order.
globally unique number and a material number for the identification of recorded material. An optional section called the “Source Pack” contains information such as the time and location of recording. A UMID with the Basic section only is called a Basic UMID. A UMID with the Source Pack is called an Extended UMID. User bits A total of 32 bits are provided in the time code which the user can use to record such information as date, reel number, or scene number on video tape or disc. Also called user’s bits.
Index A AC IN connector 20 ACCESS indicator 12 Alarms 107 Arrow buttons 16 Audio format 15 AUDIO INPUT 1/3 and 2/4 connectors 19 Audio level meters 15 Audio monitor channels 16 AUDIO MONITOR connectors 19 AUDIO OUTPUT 1/3 and 2/4 connectors 19 Audio recording formats 43 levels 46 AV/C connection 26 B BVE-700/700A 29 C D date and time settings 31 DIGITAL AUDIO (AES/EBU) INPUT 1/2 and 3/4 connectors 19 DIGITAL AUDIO (AES/EBU) OUTPUT 1/2 and 3/4 connectors 20 Digital hours meter 106 Directory structure 75 D
J JOG button 17 Jog dial 17 Jog/shuttle transport indicators 17 K KEY INH 15 KEY INH button 14 Key operation inhibit mode 15 L LEVEL knob 13 Loading and unloading a disc 40 M MARK1 button 16 MARK2 button 16 MENU button 13 Menus 81 MONITOR connector 18 Monitor video display section 14 MPEG HD 9 N Names and functions of parts 12 NEXT button 17 Nonlinear editing system 26 O On/standby switch and indicator 12 Option boards 11, 101 PDBK-101 101 PDBK-102 102 PDBK-103 103 PDBK-104 104 OUT button 16 OUT indica
changing 50 displaying a list 49 specifying the frame 46 starting playback with 49 Thumbnail search 49 changing an image 50 changing the clip information 49 displaying a list of thumbnail images 49 selecting an image 49 TIME CODE IN connector 20 TIME CODE OUT connector 20 Time data display section 15 Time data type 15 Timecode 43 recording after setting an initial value 44 recording external timecode directly 45 recording sequentially upon the last recorded timecode 45 recording with the internal timecode g
Sony Corporation
