4-229-643-11(1) Stereo Turntable System Package Operating Instructions PMPK-DJ9000 ©2000 Sony Corporation
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. For the customers in the U.S.A. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Welcome! Thank you for purchasing the Sony Stereo Turntable System Package. Before operating the system, please read this manual thoroughly and retain it for future reference. TABLE OF CONTENTS Getting Started Unpacking 4 Assembling the Turntable 4 Connecting the Turntables to the Mixer 5 Adjusting the Turntable 6 Main features • As an entry-level DJ turntable, this system is designed for easy control even for the novice DJ. • A slip mat is supplied to enable scratch playing.
Getting Started Unpacking Assembling the Turntable Verify that the following items are included with your Stereo Turntable System Package: • PS-DJ9000 Stereo Turntable System (2) • MX-DJ9000 Audio Mixer (1) • Platter (2) • Slip mat (2) • Dust cover (with hinges) (2) • Counterweight (2) • Cartridge and headshell (2) • 45 adaptor (2) • Audio cord (with ground wire) (2) • AC power cord (2) • AC power adaptor cord (1) • Audio cord (without ground wire) (2) 4 2 5 1 3 4 1 Carefully place the platter onto
Getting Started Connecting the Turntables to the Mixer 2 Turntable INPUT(CH-1) DJ MIX LINE1 RETURN l PHONO1 L SEND R On each turntable, connect the red plug of an audio cord to the R output jack, the white plug to the L output jack, and the ground wire to I (ground) terminal, as shown below.
Getting Started Adjusting the Turntable 7 Before attempting to play any records, be sure to complete the following steps to properly adjust the tonearm balance, tracking force and anti-skating dial. Failure to complete these adjustments will result in inferior sound quality and may cause permanent damage to the stylus and record. Make sure the turntable is level. 2 Set ANTI-SKATING to “0.” TI Restrain the counterweight with your other hand so that it does not rotate along with the scale ring.
Operations Operations Playing a Record 2 1 3 5 4 5 6,7 8,9 3,8,9 6 8 5 Remove the protective cover from the cartridge and release the arm stopper. 6 Set the cueing lever in the up position. Move the tonearm to the desired point on the record. 7 Set the cueing lever to the down position. The tonearm will descend slowly to the record and play will begin. 8 If you want to change the pitch, press the QUARTZ lock button (the QUARTZ indicator will turn off).
Operations To play an another part of the record 1 2 3 Set the cueing lever to the up position to raise the stylus. Move the tonearm to the desired position. Set the cueing lever to the down position. To play a 45 single Place the supplied 45 adaptor onto the spindle. Press SPEED to select 45 rpm. The green indicator changes to red. After you have finished using the adaptor, return it to the adaptor tray.
Additional Information Additional Information Procedure for replacing the stylus Maintenance 1 2 Stylus and Record Care 3 To prevent premature stylus and record wear, clean the stylus and record before the start of play. Clean the stylus by brushing it from back to front with a good-quality stylus-cleaning brush. Do not clean the stylus with your fingertip. If you use a liquid stylus cleaner, take care not to moisten the stylus excessively. Turn off the turntable, mixer and amplifier.
Additional Information Overhang Adjustment The arm overhang is factory adjusted. After replacing the cartridge, however, you should adjust the overhang as follows: 1 Loosen the screws of cartridge as shown below. Troubleshooting Before referring to the check list below, first verify that: • The power cord is securely connected. • The speaker cords are securely connected. Should any problem persist after taking the specified remedial actions, consult your nearest Sony dealer.
Additional Information Tempo is incorrect. MX-DJ9000 Audio Mixer b The rpm setting is incorrect. Set the rpm to that indicated on the record (i.e., 33 for 33 1/3-rpm records and 45 for 45-rpm records). b The PITCH ADJ. knob is not set to the center position. b The platter speed is incorrect. Adjust the controls on the bottom of the turntable while observing the strobe dots to obtain the correct platter speed (see page 7). Platter does not rotate.
Additional Information Parts and Controls PS-DJ9000 Stereo Turntable System L M A N B O C P D Q E R S F T G U H V W I X Y Z J K wj 1 2 3 4 5 6 7 8 9 q; qa 12 POWER ON/OFF switch Spindle Strobo lamp START/STOP button Slip mat Platter TARGET LIGHT and release button The TARGET LIGHT allows you to see the position of the stylus in the dark. Push and depress the TARGET LIGHT to turn it off. Push the release button to raise the light again and turn it on.
Additional Information MX-DJ9000 Audio Mixer (control panel) Control of the turntable signal is possible only after the PHONO/LINE switches (5) are set to PHONO. The signal is then controlled via the CH-1 and CH-2 faders. Connect a tape recorder, tuner, CD player, cassette deck or any other line signal to the LINE/AUX jacks on the rear panel. Control of the line signal is possible only after the PHONO/LINE switches are set to LINE. The signal is then controlled via the respective faders.
Additional Information MX-DJ9000 Audio Mixer (Rear Panel) INPUT(CH-2) OUTPUT ADAPTER DC 15V IN + LINE LINE2 INPUT(CH-1) PHONO2 LINE1 PHONO1 L L R R – M 14 REC N O qd ADAPTER DC 15V IN Connect AC power adaptor here. qf REC OUTPUT jacks Use these jacks to connect a recording unit. qg LINE OUTPUT jacks Use these jacks to connect a stereo component system or a power amplifier. P Q R qh LINE INPUT jacks Use these jacks to connect CD players or tape decks.
Sony Corporation Printed in Malaysia
