2-888-026-11(1) Integrated Remote Commander Operating Instructions GB Mode d’emploi FR RM-VL1400T © 2006 Sony Corporation
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Features The RM-VL1400T Remote Commander provides centralized control of all your A/V components from a single Remote Commander and saves the trouble of operating different A/V components with different remote control devices. The following are its main features. Control up to 10 components Setting up to 10 series of commands (Component Macros) of up to 32 consecutive steps Up to 10 series of commands (Component Macros) which provide up to 32 consecutive steps by pressing a single button can be set.
Table of Contents Features .......................................... 3 Getting Started Unpacking ....................................... 5 Installing the batteries ................... 5 Location and function of controls ........................................ 6 Basic Operations Setting operations of A/V components ................................. 7 Setting A/V components which are not listed in the Preset Code List .....................................
Getting Started Unpacking Check the contents of the package before using the Remote Commander. • Remote Commander RM-VL1400T (1) Installing the batteries Slide and open the battery compartment lid and insert two LR6 (size AA) alkaline batteries (not supplied). Be sure to match the + and – indications of the batteries with the + and – indications of the battery compartment.
qa % (muting) button* (page 10) Location and function of controls Remote Commander Silences the sound. Press the button to silence, and again to return to the previous volume level. qs GUIDE button qd OK and cursor (V/v/B/b) buttons qf RETURN button qg Player control (m/N/M/ z/x/X) buttons qh 1 (power) button qj OTHER button Used to display A/V components that are not set to the COMPONENT select buttons. Press to toggle among between 2 pages. qk 2-/ENT (enter) button Selects the programme.
Basic Operations Setting operations of A/V components —Setting component code The Remote Commander is preset at the factory to operate Sony brand A/V components. (Refer to the table below.) If you are using the Remote Commander with factory-set Sony components, skip the following procedures. To use with other brand A/V components, or Sony A/V components which do not function with the Remote Commander, you need to follow the procedures to set the component code.
5 Press the number buttons to enter the four-digit preset code, then press the OK button or the centre Label select button. Example: To enter “8095” Press 8, 0, 9, 5 then the OK button. A beep sounds, and the four-digit preset code you have set and “OK” appear on the screen, then the display returns to the screen shown in step 3. 6 To set preset codes for other A/V components, repeat steps 4 and 5. 7 Press the (light) button or the RETURN button twice.
4 Press the PROGRAM + or PROGRAM – button, then press the 1 (power) button repeatedly until the A/V component reacts as follows: TV: Powers off. Amplifier: Powers off or the volume turns up. CD player, MD deck, Casssette deck: Powers off or starts playing. Other component: Powers on Operating your A/V components with the Remote Commander Select the desired A/V component by pressing the COMPONENT select button on the Remote Commander, then operate the A/V component.
Operating A/V components Press the appropriate buttons on the Remote Commander to operate your A/V components. You can select the functions displayed on the screen with the Label select buttons corresponding to each function. The functions displayed on the screen change by pressing the SCROLL button repeatedly. Adjusting the volume Press the 2 (volume) +/– buttons to adjust the volume. Press the % (muting) button to silence the sound temporarily.
Checking the button function Other Useful Functions —Labelling function Operating the Remote Commander in the dark (light) button When you press a button, its function appears in the second line on the screen while transmitting the remote control signals. You can also display the function without transmitting the remote control signals. To change the characters displayed on the screen, see “Changing the characters on the screen” (page 15).
Advanced Operations Programming Signals of Another Remote Control 4 —Learning function To operate non-preset A/V components or button functions, use the following “learning” procedure to “programme” any of the programmable signals on the Remote Commander’s buttons. You can also use the Learning function to change the signal of individual buttons after setting the preset code (page 7). You may find it useful to change the label (page 15) of the learned button.
Notes • If you do not input anything into the Remote Commander within 60 seconds between each step, the setup procedure will be cancelled and the set mode closes. Start over from the beginning. • If you do not perform step 6 within 10 seconds after performing step 5, a beep sounds twice and the selected button name and “NG” appear in the third line on the screen, then the display returns to the screen shown in step 4. Start over from step 5.
If the Remote Commander does not seem to be working properly If the learned button does not operate properly, clear the learned signal first (page 14), then perform the learning procedure from step 1 again. (For example, if the volume becomes very loud after pressing the 2 (volume) + button just once, noise may have interfered during the learning procedure.) Changing or clearing the function of a “learned” signal To change the “learned” function, clear it first and perform the learning procedure again.
5 To clear the learned signals from other buttons, repeat steps 3 and 4. 6 Press the (light) button. The display returns to the screen shown in step 2. 7 Press the (light) button or the RETURN button twice. The set mode closes, and the Remote Commander returns to standby for operating the A/V components.
Changing the A/V component name Changing the function name of Label select buttons Up to 6 characters or digits can be input. Up to 6 characters or digits can be input. 1 1 While pressing the (light) button, press the OTHER button. “SET MODE” appears as the screen title. 2 Press the V/v buttons to select “3 LABEL”, then press the OK button or the centre Label select button. While pressing the (light) button, press the OTHER button. “SET MODE” appears as the screen title.
5 Press the number buttons or V/v buttons to input digits or characters. 3 Begin inputting digits or characters from the position where the cursor (x) is displayed. Press the B/b buttons or the left or right Label select button to move the cursor (x). 6 Press the COMPONENT select button or Label select button on which the A/V component with the function label you want to change is set. The selected A/V component appears in the second line on the screen.
Using the Series of Commands (Component Macro) You can set an operation programme consisting of up to 32 steps (Component Macro) on the COMPONENT select button or Label select button corresponding to any component. For example, when you watch a DVD by connecting a TV and DVD recorder to an amplifier, a series of operations like the ones below are necessary. 1 Turn on the TV. 2 Turn on the DVD recorder. 3 Turn on the amplifier. 4 Select the appropriate video input on the TV to watch the DVD.
5 Press the DVD button, the press the 1 (power) button. 6 Press the OTHER button repeatedly, press the Label select button corresponding to the amplifier, then press the 1 (power) button. 7 Press the t (input select) button repeatedly to select the appropriate video input on the TV to watch the DVD. 8 Press the input select button on the amplifier to select the appropriate audio input to watch the DVD. 9 Press the DVD button, then press N. 10 Press the (light) button.
3 While pressing the SCROLL button, press the COMPONENT select button or Label select button to which the desired Component Macro has been programmed. “MACRO” and the selected A/V component name appear on the first line and the programmed steps are listed on the screen. 4 Clearing programmed steps of a Component Macro If you make a mistake in programming steps or you want to programme a new Component Macro, follow the procedure below to clear the Component Macro.
Setting the power-on command of a selected A/V component 4 Press the TV button. A beep sounds and “TV ON” appears in the third line of the screen. (for Sony components only) You can set A/V components to turn on when they are selected. This function is effective only for Sony components. Example: To programme the power-on function on the TV button 1 While pressing the (light) button, press the OTHER button. “SET MODE” appears as the screen title.
Copying the settings of a COMPONENT select button to another button 3 “COPY” appears as the screen title. You can copy the entire settings of a COMPONENT select button or Label select button to another COMPONENT select button or Label select button. Tip Notes • You cannot copy the settings to a COMPONENT select button or Label select button on which any “learned” function (page 12) or Component Macro (page 18) has been programmed or A/V component’s name or label has been changed.
Controlling the volume of visual components connected to an audio component The volume control buttons (2 +/- and %) of the Remote Commander are factory preset to control the volume based on the assumption that you hear the sound of your visual components from your TV speakers, and that you hear sound of your audio components from the loudspeakers connected to your amplifier.
Others Setting the button illumination You can change the setting of the button illumination of the Remote Commander. The button illumination is preset at the factory to turn off automatically if you do not operate within 10 seconds. You can also change the brightness and fade effect (which adjusts the brightness of the button illumination) of the button illumination and which buttons activate the button illumination. 1 4 Press the B/b buttons or the left or right Label select button.
9 Press the V/v buttons to select “3 FADE EFFECT”, then press the OK button. “FADE EFFECT” appears as the screen title, and the current setting is shown inside the [ ]. 14 Press the (light) button or the RETURN button three times. The set mode closes, and the Remote Commander returns to standby for operating the A/V components. Tip If a number is displayed before the menu, you can select the menu by pressing the number button. 10 Press the B/b buttons or the left or right Label select button.
Setting the display 5 You can change the setting of the display. The Remote Commander is preset at the factory to turn off the display automatically if you do not operate it within 30 seconds. You can also change the brightness of the display. 1 While pressing the (light) button, press the OTHER button. “UNIT SETTINGS” appears as the screen title. 6 “SET MODE” appears as the screen title. 2 Tip If a number is displayed before the menu, you can select the menu by pressing the number button.
Setting the beep 4 The Remote Commander is preset at the factory with the confirmation beep set to on. You can change the setting to turn off the beep. 1 While pressing the (light) button, press the OTHER button. “SET MODE” appears as the screen title. 2 Press the V/v buttons to select “5 UNIT SETTINGS”, then press the OK button or the centre Label select button. Press the B/b buttons or the left or right Label select button.
Resetting the settings Resetting a COMPONENT select button or Label select button You can reset the A/V component settings to the factory preset. 1 While pressing the (light) button, press the OTHER button. “SET MODE” appears as the screen title. 2 Press the V/v buttons to select “7 RESET”, then press the OK button or the centre Label select button. “RESET” appears as the screen title. Tip If a number is displayed before the menu, you can select the menu by pressing the number button.
Resetting all settings 5 You can reset all settings to the factory preset. 1 While pressing the (light) button, press the OTHER button. Press the b button or the right Label select button, then press the OK button or the centre Label select button. When resetting is complete, a beep sounds and all settings return to the factory settings. Tip If you select “NO” and press the OK button or the centre Label select button, the display returns to the screen shown in step 2.
Additional Information Precautions Specifications • Do not drop the unit or give a shock to the unit, or it may cause a malfunction. • Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or sand, moisture, rain or mechanical shock. • Do not put foreign objects into the unit. Should any liquid or solid object fall into the unit, have it checked by qualified personnel before operating the unit any further.
Troubleshooting If you have problems setting up or using the Remote Commander, first check the batteries (page 5), then check the items below. Problem Solution You cannot operate the components. • Move closer to the component. The maximum operating distance is approximately 32.8 ft. (10 m). • Check that you are aiming the Remote Commander directly at the component, and that there are no obstructions between the Remote Commander and the component. • Turn on the A/V components first, if necessary.
Problem Solution You cannot operate a component even after you programmed the remote control signals with the “learning” function. Make sure that the Remote Commander has learned the correct signals. If not, see “Notes” on page 13 or “For accurate learning” (page 14), and try the learning procedure again (page 12). “NG” appears in the third line on the screen and a beep sounds five times while setting the preset code. Preset code setting has not succeeded.
Problem Solution A Component Macro does not function correctly. • When programming a Component Macro, programme the actions in the correct order (page 18). • Change the direction of the Remote Commander. If it does not improve, position the Remote Commander closer to each A/V component. • Check that the programmed A/V components are ready to receive the signals correctly (page 18).
Table of Preset Functions The Remote Commander memorizes major brands’ remote control signals. Setting the preset code (page 7) enables the Remote Commander to operate each AV component. The Remote Commander is preset at the factory to operate Sony brand A/V components. (Refer to the table below.) Screen title Code No.
TV (Analogue) Button/Display Label Function 1 POWER To turn the power on/off t INPUT To change the input mode 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER To change the programme. For example, to change the programme 5, press 0 and 5 (or, press 5 and ENT). 2 +, – VOLUME+ Volume up: + VOLUME– Volume down: – % MUTING To silence the sound on the TV. Press again to return to the previous volume level.
TV (Digital) Button/Display Buttons Label Function 1 POWER To turn the power on/off t INPUT To change the input mode 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER To change the programme. For example, to change the programme 5, press 0 and 5 (or, press 5 and ENT). 2 +, – VOLUME+ Volume up: + VOLUME– Volume down: – % MUTING To silence the sound on the TV. Press again to return to the previous volume level.
VCR (Video Cassette Recorder) Label Function 1 POWER To turn the power on/off t ANT/SW To switch the aerial output 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER To change the programme. For example, to change the programme 5, press 0 and 5 (or, press 5 and ENT).
Analogue Satellite Receiver Digital Satellite Receiver Label Function 1 POWER To turn the power on/off t INPUT To switch the output of the satellite receiver to the TV. (When you connect a TV cable or aerial to the receiver, the output switches between a TV and satellite programme.
Digital Satellite Receiver (No. 3201) Button/Display Label Function 1 POWER To turn the power on/off t INPUT To switch the output of the satellite receiver to the TV. (When you connect a TV cable or aerial to the receiver, the output switches between a TV and satellite programme.
DVD Player Label Function POWER To turn the power on/off 1-9, 0 1-9, 0 Number buttons: To set items selected from the screen - (1-) +10 To select numbers 10 and above ENT (2-) ENTER To enter the setting. To set items selected from the screen. PROGRAM +, – > To proceed to the next location or song .
Analogue Cable Box Button/Display Label Function POWER To turn the power on/off 1-9, 0 To change the programmes ENT (2-) ENTER To enter the programme PROGRAM +, – PROGRAM+ Programme up: + PROGRAM– Programme down: – RECALL To operate JUMP, FLASHBACK or the CHANNEL RETURN function 1 t 1-9, 0 - (1-) DIGITAL/ANALOG / a GUIDE Buttons MENU V, v, B, b OK RETURN TOOLS m N M x X z (REC) A (Red) B (Green) C (Yellow) D (Blue) Continued 41GB
DVD Recorder DVD/VCR Combo*1 Button/Display Label Function POWER To turn the power on/off 1-9, 0 1-9, 0 Number buttons: To set items selected on the screen - (1-) +10 To select numbers 10 and above ENT (2-) ENTER To enter a setting or to set items selected on the screen PROGRAM +, – PROGRAM+ Programme up: + PROGRAM– Programme down: – DECKCHANGE To switch the deck / DISPLAY To show the current play status on the screen a SUBTITLE To switch the subtitle GUIDE TOP MENU To display t
Home Theatre System/DVD Player Combo Function POWER To turn the power on/off t INPUT To change the input mode 1-9, 0 1-9, 0 Number buttons: To set items selected on the screen - (1-) +10 To select numbers 10 and above ENT (2-) ENTER To enter a setting or to set items selected on the screen 2 +, – VOLUME+ Volume up: + VOLUME– Volume down: – % MUTING To silence the sound on the Home Theatre System/ DVD Player Combo. Press again to return to the previous volume level.
Receiver/Amplifier Label Function 1 POWER To turn the power on/off t INPUT To change the input select cyclically 1 1 To select the input source: VIDEO1 2 2 To select the input source: VIDEO2 3 3 To select the input source: AUX 4 4 To select the input source: TUNER 5 5 To select the input source: CD 6 6 To select the input source: TAPE 7 7 To select the input source: MD/DAT 8 8 To select the input source: TV 9 9 To select the input source: PHONO 0 0 To select the input s
CD Player Label Function POWER To turn the power on/off 1-9, 0 1-9, 0 To select the track number - (1-) +10 To select numbers 10 and above ENT (2-) ENTER To enter the setting PROGRAM +, – > To select the next track .
MD Deck Label Function POWER To turn the power on/off 1-9, 0 1-9, 0 To select the track number - (1-) +10 To select numbers 10 and above ENT (2-) ENTER To enter the setting PROGRAM +, – > To select the next track .
Cassette Deck Button/Display Label Function POWER To turn the power on/off - (1-) DECK Ab To reverse the deck A ENT (2-) DECK Bb To reverse the deck B A/B To select the deck: Deck A or B (dual cassette deck only) V DECK BN To play the deck B v DECK Bx To stop the deck B B DECK Bm To rewind the deck B b DECK BM To fast-forward the deck B OK DECK BX To pause the deck B RETURN DECK Bz To record the deck B m DECK Am To rewind the deck A N DECK AN To play the deck A M DECK
Traitement des appareils électriques et électroniques en fin de vie (Applicable dans les pays de l’Union européenne et aux autres pays européens disposant de systèmes de collecte sélective) Ce symbole, apposé sur le produit ou sur son emballage, indique que ce produit ne doit pas être traité avec les déchets ménagers. Il doit être remis à un point de collecte approprié pour le recyclage des équipements électriques et électroniques.
Caractéristiques La télécommande RM-VL1400T permet de centraliser les commandes de l’ensemble de vos appareils audio/vidéo à partir d’une télécommande unique et vous évite d’avoir à commander différents appareils audio/vidéo à l’aide de plusieurs télécommandes. Ses principales caractéristiques sont les suivantes : Permet de commander jusqu’à 10 appareils Cette télécommande vous permet de piloter jusqu’à 10 appareils : téléviseur, récepteur satellite, magnétoscope, lecteur DVD ou CD, amplificateur, etc.
Table des matières Caractéristiques ............................. 3 Préparatifs Déballage ........................................ 5 Installation des piles ...................... 5 Emplacement et fonction des commandes .................................. 6 Opérations de base Réglage des fonctions des appareils A/V ................................ 7 Réglage des appareils A/V qui ne sont pas répertoriés dans la Liste des codes préprogrammés ........
Préparatifs Déballage Vérifiez le contenu de l’emballage avant d’utiliser cette télécommande. • Télécommande RM-VL1400T (1) Installation des piles Ouvrez le couvercle du compartiment des piles en le faisant coulisser et insérez deux piles alcalines LR6 (taille AA) (non fournies). Veillez à faire correspondre les marques + et – des piles avec les repères + et – indiqués dans le compartiment.
qa Touche* % (silence) (page 10) Emplacement et fonction des commandes Télécommande Permet de couper le son. Appuyez de nouveau sur cette touche pour rétablir le son au volume précédent. qs Touche GUIDE qd Touches OK et curseur (V/v/B/b) qf Touche RETURN qg Touches de commande du lecteur (m/N/M/z/x/X) qh Touche 1 (alimentation) qj Touche OTHER Permet d’afficher les appareils A/V qui ne sont pas réglés sur les touches de sélection COMPONENT. Appuyez sur cette touche pour basculer entre les 2 pages.
Opérations de base Réglage des fonctions des appareils A/V —Enregistrement des codes d’appareil La télécommande est programmée en usine pour commander des appareils audio/vidéo de marque Sony. (Consultez le tableau suivant). Si vous utilisez la télécommande avec des appareils Sony réglés en usine, vous pouvez ignorer la procédure suivante. Vous pouvez également utiliser la télécommande pour piloter d’autres appareils A/V préprogrammés.
5 Appuyez sur les touches numériques pour saisir le code à 4 chiffres, puis appuyez sur la touche OK ou la touche centralisée de sélection de libellé. Par exemple : Pour saisir « 8095 », appuyez sur 8, 0, 9 et 5, puis appuyez sur OK. Réglage des appareils A/V qui ne sont pas répertoriés dans la Liste des codes préprogrammés —Fonction de recherche Vous pouvez régler les appareils A/V qui ne sont pas répertoriés dans la «Liste des codes préprogrammés» fournie à l’aide de la fonction de recherche.
4 Appuyez sur PROGRAM + ou PROGRAM –, puis appuyez plusieurs fois sur la touche 1 (alimentation) jusqu’à ce que l’appareil A/V réagisse comme décrit ci-après : TV : mise hors tension. Amplificateur : mise sous tension ou augmentation du volume. Lecteur CD, Platine MD, Platine à cassette : mise sous tension ou lecture. Autre appareil : mise sous tension 5 Appuyez sur la touche OK ou sur la touche centralisée de sélection de libellé.
Utilisation des appareils A/V Appuyez sur les touches appropriées de la télécommande afin de commander vos appareils A/V. Vous pouvez sélectionner les fonctions affichées à l’écran avec les touches de sélection de libellé correspondant à chaque fonction. Les fonctions affichées à l’écran changent si vous appuyez plusieurs fois sur la touche SCROLL. Réglage du volume Appuyez sur les touches 2 (volume) +/– pour régler le volume. Appuyer sur la touche % (silence) permet de couper le son temporairement.
Autres fonctions utiles Utilisation de la télécommande dans l’obscurité Touche (éclairage) Vérification de la fonction de la touche —Fonction de libellé Lorsque vous appuyez sur une touche, sa fonction apparaît sur la deuxième ligne de l’écran lors de la transmission des signaux de commande à distance. Vous pouvez également afficher la fonction sans transmettre de signaux de commande à distance.
Fonctions avancées Programmation de signaux d’une autre télécommande 4 —Fonction de mémorisation Pour utiliser des appareils A/V non préprogrammés ou des fonctions des touches, utilisez la procédure de mémorisation suivante pour programmer sur l’une des touches de la télécommande les signaux programmables. Vous pouvez aussi utiliser la fonction de mémorisation pour changer les signaux des touches individuelles après avoir enregistré le code préprogrammé (page 7).
Remarques • Si aucune donnée n’est entrée dans la télécommande dans les 60 secondes suivant chaque étape, la procédure est annulée et le mode de réglage se ferme. Recommencez depuis le début. • Si vous n’exécutez pas l’étape 6 dans les 10 secondes après avoir exécuté l’étape 5, un bip retentit deux fois et le nom de la touche sélectionnée et « NG » apparaissent à la troisième ligne de l’écran. L’affichage revient ensuite à l’étape 4. Recommencez à l’étape 5.
Si la télécommande ne semble pas fonctionner Si la touche mémorisée ne fonctionne pas correctement, effacez tout d’abord le signal mémorisé (page 14), puis exécutez à nouveau la procédure de mémorisation à partir de l’étape 1. (Par exemple, si le volume devient trop élevé après une seule pression sur la touche 2 (volume) +, des parasites peuvent avoir interféré avec la procédure de mémorisation.
5 Pour effacer les signaux mémorisés d’autres touches, répétez les étapes 3 et 4. 6 Appuyez sur la touche (éclairage). L’écran revient à l’étape 2. 7 Modification des caractères affichés à l’écran Vous pouvez modifier les noms et fonctions des appareils A/V ou la fonction de la touche (libellé) affichée à l’écran. Les caractères et chiffres sont saisis comme suit en appuyant sur les touches numériques. Appuyez deux fois sur la touche (éclairage) ou la touche RETURN. 1 1c,c-c.
Modification du nom de l’appareil A/V Vous pouvez enregistrer jusqu’à 6 caractères ou chiffres. 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. Changement du nom de fonction des touches de sélection de libellé Vous pouvez enregistrer jusqu’à 6 caractères ou chiffres. 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. « SET MODE » s’affiche comme titre d’écran. « SET MODE » s’affiche comme titre d’écran.
5 Appuyez sur les touches numériques ou les touches V/v pour saisir les chiffres ou les caractères. 3 Commencez à saisir les chiffres ou les caractères où le curseur (x) est affiché. Appuyez sur les touches B/b ou sur la touche de sélection de libellé droite ou gauche pour déplacer le curseur (x). 6 L’appareil A/V sélectionné apparaît sur la deuxième ligne de l’écran. Appuyez sur la touche OK ou sur la touche centralisée de sélection de libellé. Un bip retentit et le nom de la fonction est modifié.
Utilisation d’une série de commandes (Macro d’appareil) Vous pouvez programmer jusqu’à 32 étapes consécutives (macro d’appareil) sur la touche de sélection COMPONENT ou la touche de sélection de libellé correspondant à un appareil. Par exemple, lorsque vous regardez un DVD en connectant un téléviseur et un graveur de DVD à un amplificateur, une série de commandes comme celles décrites ci-dessous sont nécessaires. 1 Mettez le téléviseur sous tension. 2 Mettez le graveur de DVD sous tension.
5 6 7 Appuyez sur la touche DVD, puis sur la touche 1 (alimentation). Appuyez plusieurs fois sur la touche OTHER, puis appuyez sur la touche de sélection de libellé correspondant à l’amplificateur, puis appuyez sur la touche 1 (alimentation). Vérification du fonctionnement d’une macro d’appareil Pour ce faire, suivez la procédure ci-dessous.
3 Tout en appuyant sur la touche SCROLL, appuyez sur la touche de sélection COMPONENT ou la touche de sélection de libellé sur lequel la macro d’appareil souhaitée a été programmée. « MACRO » et le nom du composant A/V sélectionné apparaissent sur la première ligne et les étapes programmées sont répertoriées sur l’écran.
Réglage de la commande de mise sous tension d’un appareil A/V sélectionné (pour un appareil Sony uniquement) Vous pouvez régler la mise sous tension d’appareils A/V lorsqu’ils sont sélectionnés. Cette fonction s’applique aux appareils Sony uniquement. Par exemple : pour programmer la fonction de mise sous tension sur la touche TV 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. « SET MODE » s’affiche comme titre d’écran.
Copie des réglages d’une touche de sélection COMPONENT sur une autre touche 3 « COPY » s’affiche comme titre d’écran. Vous pouvez copier les réglages d’une touche de sélection COMPONENT ou d’une touche de sélection de libellé sur une autre touche de sélection COMPONENT ou une autre touche de sélection de libellé. Conseil Si un chiffre s’affiche devant le menu, vous pouvez sélectionner le menu en appuyant sur la touche numérique.
Contrôle du volume des appareils vidéo raccordés à un appareil audio Les touches de commande du volume (2 +/– et %) de la télécommande ont été réglées en usine en supposant que le son de vos appareils vidéos est émis par les haut-parleurs de votre téléviseur et que le son de vos appareils audio est émis par les enceintes raccordées à votre amplificateur.
Autres Réglage de l’éclairage de la touche Vous pouvez modifier le réglage de l’éclairage de la touche de la télécommande. L’éclairage de la touche est préprogrammé en usine pour s’éteindre automatiquement si vous n’utilisez pas la télécommande dans les 10 secondes. Vous pouvez également modifier la luminosité et l’effet fondu (qui règle la luminosité de l’éclairage de la touche) de l’éclairage de la touche et les touches qui activent l’éclairage de la touche.
9 Appuyez sur les touches V/v pour sélectionner « 3 FADE EFFECT », puis appuyez sur la touche OK. « FADE EFFECT » apparaît comme titre d’écran et le réglage courant est indiqué entre [ ]. 14 Appuyez trois fois sur la touche (éclairage) ou la touche RETURN. Le mode de réglage se ferme et la télécommande revient en mode veille pour l’utilisation des appareils A/V. Conseil Si un chiffre s’affiche devant le menu, vous pouvez sélectionner le menu en appuyant sur la touche numérique.
Réglage de l’affichage 5 Vous pouvez modifier le réglage de l’affichage. La télécommande est préprogrammée en usine pour éteindre automatiquement l’affichage si vous ne l’utilisez pas dans les 30 secondes. La luminosité de l’affichage peut également être modifiée. 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. Appuyez sur la touche (éclairage), la touche centralisée de sélection de libellé, la touche OK ou la touche RETURN.
Réglage du bip 4 La télécommande est programmée en usine avec un bip de confirmation activé. Vous pouvez modifier le réglage pour désactiver le bip. 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. « SET MODE » s’affiche comme titre d’écran. Appuyez sur les touches B/b ou sur la touche droite ou gauche de sélection de libellé. A chaque modification de réglage, un bip retentit et [ ] est défini sur le nouveau réglage. ON : Active le bip sonore.
Réinitialisation des réglages Réinitialisation d’une touche de sélection COMPONENT ou d’une touche de sélection de libellé Vous pouvez réinitialiser les réglages de l’appareil A/V à leurs réglages par défaut. 1 Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. « SET MODE » s’affiche comme titre d’écran. 2 Appuyez sur les touches V/v pour sélectionner « 7 RESET », puis appuyez sur la touche OK ou sur la touche centralisée de sélection de libellé.
Réinitialisation de tous les réglages 4 Vous pouvez réinitialiser tous les réglages de l’appareil. 1 Appuyez sur la touche b ou sur la touche droite de sélection de libellé, puis appuyez sur la touche OK ou sur la touche centralisée de sélection du libellé. Tout en maintenant la touche (éclairage) enfoncée, appuyez sur la touche OTHER. « REALLY? » apparaît sur la deuxième ligne de l’écran et « NO » est indiqué entre [ ]. « SET MODE » s’affiche comme titre d’écran.
Informations complémentaires Précautions • Ne pas laisser tomber la télécommande ni la soumettre à des chocs, car ceci pourrait provoquer des problèmes de fonctionnement. • Ne pas placer la télécommande à proximité de sources de chaleur ni dans un endroit soumis aux rayons du soleil ou à de grandes quantités de poussière ou de sable, à la pluie, à l’humidité ou à des chocs mécaniques. • Ne rien insérer dans la télécommande.
Dépannage En cas de problème concernant le réglage ou l’utilisation de la télécommande, commencez par vérifier les piles (page 5), puis les points suivants. Problème Vous ne pouvez pas commander les appareils. Vous ne pouvez pas utiliser les appareils, même après avoir réglé le code préprogrammé. Vous ne pouvez pas contrôler le volume. La télécommande ne peut pas mémoriser les signaux de commande à distance. Solution • Rapprochez-vous de l’appareil. La portée maximale est d’environ 10 m.
Problème Vous ne pouvez pas commander un appareil, même après avoir enregistré les signaux de commande à distance avec la fonction de mémorisation. « NG » apparaît sur la troisième ligne de l’écran et un bip retentit 5 fois lors du réglage du code préréglé. « NG » apparaît sur la troisième ligne de l’écran et un bip retentit 5 fois lors de la mémorisation. « FULL » apparaît sur la troisième ligne de l’écran et un bip retentit 5 fois lors de la mémorisation.
Problème Une macro d’appareil ne fonctionne pas correctement. L’écran se met automatiquement hors tension. Le mode de réglage se ferme brusquement lors du réglage. Le bip de confirmation ne retentit pas. Le bip de confirmation retentit même si le son est coupé. «E» apparaît à l’écran. La télécommande n’entre pas en mode de réglage. Solution • Lors de la programmation d’une macro d’appareil, programmez les opérations dans le bon ordre (page 18). • Changez l’orientation de la télécommande.
Tableaux des fonctions préréglées La télécommande mémorise les signaux de commande à distance des principales marques. La section Réglage du code préprogrammé (page 7) vous indique comment régler votre télécommande afin de commander vos appareils. La télécommande est programmée en usine pour commander des appareils audio/vidéo de marque Sony. (Consultez le tableau suivant).
Téléviseur (analogique) Touche/affichage Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t INPUT Pour changer le mode d’entrée 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER Pour changer de programme Par exemple, pour passer à la chaîne 5, appuyez sur 0 et 5 (ou appuyez sur 5 et ENT) 2 +, – VOLUME+ Augmentation du volume : + VOLUME– Diminution du volume : – % MUTING Pour couper le son du téléviseur. Appuyez de nouveau pour revenir au niveau de volume précédent.
Téléviseur (numérique) Touche/affichage Touches Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t INPUT Pour changer le mode d’entrée 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER Pour changer de programme Par exemple, pour passer à la chaîne 5, appuyez sur 0 et 5 (ou appuyez sur 5 et ENT) 2 +, – VOLUME+ Augmentation du volume : + VOLUME– Diminution du volume : – % MUTING Pour couper le son du téléviseur.
Magnétoscope Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t ANT/SW Pour commuter la sortie d’antenne 1-9, 0, - (1-), ENT (2-) 1-9, 0, -/--, ENTER Pour changer de programme Par exemple, pour passer à la chaîne 5, appuyez sur 0 et 5 (ou appuyez sur 5 et ENT) PROGRAM +, – PROGRAM+ Chaîne suivante : + PROGRAM– Chaîne précédente : – / DISPLAY Pour activer l’affichage à l’écran a INPUT Pour changer le mode d’entrée MENU MENU Pour appeler l’affichage MENU V, v, B, b R, r,
Récepteur satellite analogique Récepteur satellite numérique Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t INPUT Pour basculer la sortie du récepteur satellite sur le téléviseur. (Lorsque vous raccordez un câble TV ou une antenne au récepteur, la sortie est commutée entre un programme TV et un programme satellite.
Récepteur satellite numérique (No. 3201) Touche/affichage Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t INPUT Pour basculer la sortie du récepteur satellite sur le téléviseur. (Lorsque vous raccordez un câble TV ou une antenne au récepteur, la sortie est commutée entre un programme TV et un programme satellite.
Lecteur de DVD Etiquette Fonction POWER Pour la mise sous ou hors tension 1-9, 0 1-9, 0 Touches numériques : Pour régler les paramètres sélectionnés à l’écran - (1-) +10 Pour sélectionner 10 et les nombres supérieurs à 10 ENT (2-) ENTER Pour valider le réglage. Pour régler les paramètres sélectionnés à l’écran PROGRAM +, – > Pour passer à l’endroit ou au morceau suivant .
Décodeur analogique Touche/affichage Etiquette Fonction POWER Pour la mise sous ou hors tension 1-9, 0 Pour changer les programmes ENT (2-) ENTER Pour entrer dans le programme PROGRAM +, – PROGRAM+ Chaîne suivante : + PROGRAM– Chaîne précédente : – RECALL Pour contrôler la fonction JUMP, FLASHBACK ou CHANNEL RETURN 1 t 1-9, 0 - (1-) DIGITAL/ANALOG / a GUIDE Touches MENU V, v, B, b OK RETURN TOOLS m N M x X z (REC) A (Red) B (Green) C (Yellow) D (Blue) suite page suivante 41FR
Graveur de DVD Combiné DVD/magnétoscope*1 Touche/affichage Etiquette Fonction POWER Pour la mise sous ou hors tension 1-9, 0 1-9, 0 Touches numériques : Pour régler les paramètres sélectionnés à l’écran - (1-) +10 Pour sélectionner 10 et les nombres supérieurs à 10 ENT (2-) ENTER Pour valider un réglage ou régler les paramètres sélectionnés sur l’écran PROGRAM +, – PROGRAM+ Chaîne suivante : + PROGRAM– Chaîne précédente : – DECKCHANGE Pour commuter la platine / DISPLAY Pour indiquer l
Système Home cinéma/Combiné lecteur de DVD Fonction POWER Pour la mise sous ou hors tension t INPUT Pour changer le mode d’entrée 1-9, 0 1-9, 0 Touches numériques : Pour régler les paramètres sélectionnés à l’écran - (1-) +10 Pour sélectionner 10 et les nombres supérieurs à 10 ENT (2-) ENTER Pour valider un réglage ou régler les paramètres sélectionnés sur l’écran 2 +, – VOLUME+ Augmentation du volume : + VOLUME– Diminution du volume : – % MUTING Pour couper le son du Home cinéma ou d
Récepteur/amplificateur Etiquette Fonction 1 POWER Pour la mise sous ou hors tension t INPUT Pour changer la sélection d’entrée de manière cyclique 1 1 Pour sélectionner la source d’entrée : VIDEO1 2 2 Pour sélectionner la source d’entrée : VIDEO2 3 3 Pour sélectionner la source d’entrée : AUX 4 4 Pour sélectionner la source d’entrée : TUNER 5 5 Pour sélectionner la source d’entrée : CD 6 6 Pour sélectionner la source d’entrée : TAPE 7 7 Pour sélectionner la source d’entrée : MD
Lecteur de CD Etiquette Fonction POWER Pour la mise sous ou hors tension 1-9, 0 1-9, 0 Pour sélectionner le numéro de plage - (1-) +10 Pour sélectionner 10 et les nombres supérieurs à 10 ENT (2-) ENTER Pour valider le réglage PROGRAM +, – > Pour sélectionner la plage suivante .
Platine MD Etiquette Fonction POWER Pour la mise sous ou hors tension 1-9, 0 1-9, 0 Pour sélectionner le numéro de plage - (1-) +10 Pour sélectionner 10 et les nombres supérieurs à 10 ENT (2-) ENTER Pour valider le réglage PROGRAM +, – > Pour sélectionner la plage suivante .
Platine à cassette Touche/affichage Etiquette Fonction POWER Pour la mise sous ou hors tension - (1-) DECK Ab Pour inverser la platine A ENT (2-) DECK Bb Pour inverser la platine B A/B Pour sélectionner la platine : Platine A ou B (platine à cassette double seulement) V DECK BN Pour lire la platine B v DECK Bx Pour arrêter la platine B B DECK Bm Pour rembobiner la platine B b DECK BM Pour avancer rapidement la platine B OK DECK BX Pour arrêter la platine B RETURN DECK Bz Pour
Printed in Malaysia