masterpage: Left 010COV.
masterpage: Left 010COV.book Page 2 Friday, March 25, 2016 11:05 AM Table of Contents Features Features. . . . . . . . . . . . . . . . . . . 2 Guide to Parts and Controls. . . 3 Bring your smartphone to easily control calls, music and more. This In-car Bluetooth® Commander for Smartphone has Sony’s voice technology app activation and an intuitively designed keypad, so you can keep using your Smartphone without ever taking your eyes off the road.
masterpage: Left 010COV.book Page 3 Friday, March 25, 2016 11:05 AM Guide to Parts and Controls Adaptor MODE Switches between volume mode and zoom mode. PAIRING Press and hold for 2 seconds to set pairing. Press and hold for 7 seconds to reset pairing history and MODE setting of the adaptor. Flashes slowly in BLUETOOTH standby mode. Stays lit while connected using BLUETOOTH. MIC (microphone) Built-in microphone. It is not available when the external microphone is installed.
masterpage: Left 010COV.book Page 4 Friday, March 25, 2016 11:05 AM RM-X7S Remote commander / Forward/reverse the track on the music app. N-Mark Touch with an Android smartphone to make a BLUETOOTH connection. VOICE Activate the Assistant for RMX7BT function (only Android smartphones installed with the app) or the Siri function (iPhone only). Press and hold for 2 seconds to activate voice dial (Android smartphones only).
masterpage: Left 010COV.book Page 5 Friday, March 25, 2016 11:05 AM Connection/Installation Cautions It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations. Avoid installing the adaptor and remote commander in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight, on the dashboard or near heater ducts.
masterpage: Left 010COV.book Page 6 Friday, March 25, 2016 11:05 AM Connection Connecting to an AUX input jack/USB port in the console box Connecting to an AUX input jack/USB port under the console panel Notes Connect the adaptor with the AUX cable and USB cable . Install the adaptor to a site where it can receive the IR signal of the remote commander.
masterpage: Left 010COV.book Page 7 Friday, March 25, 2016 11:05 AM Installation + side up Installing the lithium battery 1 Pull the remote commander while pressing the holder release button on the holder to remove from the holder. Replacing the lithium battery of the remote commander Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.
masterpage: Left 010COV.book Page 8 Friday, March 25, 2016 11:05 AM Installing the remote commander 2 Peel the tape on the bottom of the holder and attach it on the installation site. Fix the hole of the holder on the hole of the car. 3 Install the supplied screw to the hole of the holder and secure it to the installation site. Before installing Make sure that the angle of slant at the holder or the direction of remote commander is suitable for the installation site.
masterpage: Left 010COV.book Page 9 Friday, March 25, 2016 11:05 AM Installing the adaptor 1 Attach the adaptor to the installation site using the supplied double-sided tape . Getting Started Turning the Power on 1 Turn the ignition on or set the ignition to ACC. The adaptor turns on. To turn the power off Turn the ignition off. The adaptor turns off. Note If your car’s ignition has no ACC position, remove the USB cable each time you turn the ignition off to prevent battery drain.
masterpage: Left 010COV.book Page 10 Friday, March 25, 2016 11:05 AM NFC function, data communication can be achieved easily just by touching the relevant symbol or designated location on NFC compatible devices. For details, refer to the operating instructions supplied with the car audio unit.
masterpage: Left 010COV.book Page 11 Friday, March 25, 2016 11:05 AM Notes When making the connection, handle the smartphone carefully to prevent scratches. One touch connection is not possible when the adaptor is already connected to another NFC compatible device. In this case, disconnect the other device, and make connection with the smartphone again.
masterpage: Left 010COV.book Page 12 Friday, March 25, 2016 11:05 AM Connecting with a paired BLUETOOTH device To use a paired device, connection with this adaptor is required. Some paired devices will connect automatically. Tips The adaptor remembers the 5 most recently paired devices. If the BLUETOOTH signal on, when the ignition is turned on, this adaptor automatically reconnects to the most recently connected smartphone.
masterpage: Left 010COV.book Page 13 Friday, March 25, 2016 11:05 AM 2 3 Make sure that stays lit. If a connection has not been established, select [RM-X7BT] on the BLUETOOTH device. Press on the remote commander. Start audio playback with the music app on the connected BLUETOOTH device. Note Once the adaptor and the BLUETOOTH device are connected, you can control playback by pressing and /.
masterpage: Left 010COV.book Page 14 Friday, March 25, 2016 11:05 AM To switch between handsfree mode and handheld mode During a call, press and hold to switch the phone call audio between the adaptor and smartphone. Using Voice Recognition You can control an application by voice command. Note For your safety, follow your local traffic laws and regulations, and do not operate the application while driving.
masterpage: Left 010COV.book Page 15 Friday, March 25, 2016 11:05 AM Using Siri Eyes Free Siri Eyes Free allows you to use an iPhone handsfree by simply speaking into the microphone. You can perform the handsfree registration for an iPhone that supports Siri Eyes Free. Availability is limited iPhone 4s or later. Make sure that your iPhone is running the latest iOS version. 1 Activate the Siri function on the iPhone. For details, refer to the operating instructions supplied with the iPhone.
masterpage: Left 010COV.book Page 16 Friday, March 25, 2016 11:05 AM Additional Information Troubleshooting The following checklist will help you remedy problems you may encounter with your adaptor and remote commander. Before going through the checklist below, check the connection and operating procedures. If the problem is not solved, visit the support site on the reference guide (separate document). General No sound or the sound is very low. The volume of the connected device is very low.
masterpage: Left 010COV.book Page 17 Friday, March 25, 2016 11:05 AM No ringtone. Depending on the connecting device, the ringtone may not be sent properly. If these solutions do not help improve the situation, consult your nearest Sony dealer. The sound skips during playback of a BLUETOOTH audio device. Reduce the distance between the adaptor and the BLUETOOTH audio device.
masterpage: Left 010COV.
masterpage: Left 010COV.
masterpage: Left 010COV.book Page 20 Friday, March 25, 2016 11:05 AM http://www.sony.