4-095-518-E1 (2) Wall-Mount Bracket Operating Instructions • This Wall-Mount Bracket is designed for use with the Sony KLV-SG21M1 LCD Color TV.
Thank you for purchasing this product. For Customers Sufficient expertise is required for installing this product, especially to assure the strength of the wall. Be sure to entrust the attachment of this product on the wall (Step 1 to Step 3 in “Installation”) to qualified service personnel and pay adequate attention to safety during the installation. We are not liable for any damage or injury caused by mishandling or improper installation.
Caution • This Wall-Mount Bracket is only for the specified Sony LCD Color TVs. Do not use the bracket with a TV whose operating instructions do not specify the use of this bracket. • Be especially careful not to drop the TV when you install it high on a wall. Installation For qualified service personnel For the installation, have ready eight commercially available mounting screws, anchor bolts, etc. that are appropriate for the wall.
Step 2: Decide the installation location Decide the location on the wall to install the TV. Then, place bracket A on the installation location and mark the four screw holes on the wall using a pencil. Before marking the location of the holes, make sure that the distance between the upper edge of bracket A and the ceiling is 15 cm or more, and that between the side edge of bracket A and the side wall is 25 cm or more. Ceiling Bracket A 25 cm or more 15 cm or more Mark this portion using a pencil.
Step 3: Secure bracket A to the wall 1 Insert four of the screws you prepared at the positions marked in Step 2 (page 4). Do not tighten the screws completely for the moment. Keep a space of 2 to 3 mm from the wall. Wall Screws you prepared 2 - 3 mm 2 Press bracket A to the wall and slide it down. Then fully tighten the four screws on the wall. Bracket A Bracket A Wall Wall 3 Insert four of the screws you prepared in the screw holes, and tighten them securely in the order of 1 to 4 as shown below.
Step 4: Attach bracket B to the TV Before attaching bracket B, remove the rear cover of the TV and disconnect all the cables from the TV. See the Operating Instructions for the KLV-SG21M1 for details on detaching the rear cover. 1 Remove the five screws and detach the TV stand from the TV. To protect the LCD panel surface from possible damages, lay the TV face down on a soft cloth. Remove these screws.
2 Align the four holes on bracket B to the corresponding holes on the rear panel then secure the bracket to the TV using four of the five screws you removed previously. Rear of the TV Bracket B Note Keep the remaininig screw for future use. Use it to secure the stand to the TV again. Step 5: Connect the cables 1 Connect the cables. Bundle the cables and secure them with the clips. Do not attach the rear cover.
Step 6: Attach brackets C, D, and E to the TV 1 Attach bracket C of the desired angle to bracket B. Insert the hooked part of bracket C into bracket B as illustrated below. Confirm that both sides of bracket C are outside bracket B, and secure them firmly with two of the supplied screws. There are three types of bracket C, each with a different angle: 0°, 5°, and 10°. Choose the bracket C with the desired angle to attach.
2 Attach bracket D to bracket C, and secure them firmly with two of the supplied screws. Place bracket D onto bracket C as illustrated below, and secure them with the two screws. Bracket D 3 Attach bracket E to bracket C, and secure them firmly with two of the supplied screws. Slide the shaft of bracket E into the notches of bracket C as illustrated below, and secure them with the two screws one on each side.
Step 7: Secure the TV to the wall 1 Hook bracket E on bracket A. Bracket A Bracket E Wall Notes • Hold the TV firmly. Be especially careful when you secure the TV in a high place. • Do not release the TV until you confirm that bracket E is firmly secured to bracket A at three locations.
2 Insert the locking rod. The locking rod can be inserted from either side. The illustration below shows an example of how to insert the locking rod from the right side. 1 Insert the longer side of the locking rod into the holes on bracket E. 2 Insert the curved side of the locking rod into the hole on bracket A. Hold and press the locking rod at part to pass its end through the hole. 3 Turn the locking rod until it stops to secure it in place.
Detaching the TV from the Wall-Mount Bracket Remove the locking rod from brackets A and E, then detach the TV from the Wall-Mount Bracket.
280 mm Specifications 168 mm Value varies depending on the angle of bracket C. Bracket C angle 0° 5° 10° 55 mm 63 mm 71 mm Bracket mass: Approx. 1.6 kg Supportable weight: Approx. 12 kg Design and specifications are subject to change without notice.
Printed in China
