3-867-314-11 (1) Cordless Telephone Operating Instructions US Manual de instrucciones ES SPP-ID975 ©1999 by Sony Corporation
Owner’s Record The model and the serial numbers are located at the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. SPP-ID975 Serial No. ________________ IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions.
6. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. 7. If trouble is experienced with this equipment (SPP-ID975), for repair or warranty information, please contact Sony Direct Response Center: Tel 1-800-222-7669.
Table of contents Getting Started 6 Read this first 7 Step 1: Checking the package contents 8 Step 2: Setting up the base phone 11 Step 3: Preparing the battery pack 14 Step 4: Entering the area code 17 Identifying the parts Basics 20 Making calls 23 Redialing 24 Receiving calls Telephone Features 26 Speed dialing 26 Storing phone numbers and names 28 Making calls with speed dialing 29 Phone Directory 29 Storing phone numbers and names 31 Changing a stored name and/or phone number 32 Erasing a memory loca
Getting Started Read this first Before you use your phone, you must first set it up. Here’s a quick way to set up your phone: Steps 1, 2, 3 and 4. Step 1 (page 7) First, unpack the phone and the supplied accessories. Step 2 (pages 8 to 10) Next, you need to do three things to set up the base phone, including finding the best location for the base phone. Base phone Step 3 (pages 11 to 12) Then, insert the battery pack into the handset and charge it for more than 12 hours.
Step 1 Checking the package contents Make sure you have received the following items in the package. If anything is missing, contact your local Sony dealer.
Step 2 Setting up the base phone Do the following steps: • Choose the best location • Connect the base phone • Choose the dialing mode Choose the best location Where you place the base phone affects the reception quality of the handset.
Connect the base phone If you want to hang the base phone on the wall, see page 51. 3 Getting Started Hook the cord. To an AC outlet To DC IN 9V 2 AC power adaptor (supplied AC-T122) To LINE 1 Telephone line cord To the telephone outlet (supplied) 1 Connect the telephone line cord to the LINE jack and to a telephone outlet. 2 Connect the AC power adaptor to the DC IN 9V jack and to an AC outlet. 3 Raise the antenna. Make sure it points towards the ceiling.
Step 2: Setting up the base phone (continued) Notes • Use only the supplied AC-T122 AC power adaptor. Do not use any other AC power adaptor. • Connect the AC power adaptor to a continuous power supply. • Place the base phone close to the AC outlet so that you can unplug the AC power adaptor easily. Tip If your telephone outlet is not modular, contact your telephone service company for assistance.
Step 3 Preparing the battery pack Charge the battery pack for more than 12 hours before you start using your phone. compartment lid of the handset. 2 Insert the battery pack (with BP-T23 contacts facing down) into the battery compartment. Getting Started 1 Slide open the battery 3 Close the battery compartment lid. 4 Place the handset on the base phone. You can place it with either side facing up.
Step 3: Preparing the battery pack (continued) Battery duration A fully charged battery pack lasts for about: • Approx. 6 hours when you use the handset continuously • Approx. 7 days when the handset is in standby mode. Notes • The battery pack will gradually discharge over a long period of time, even when not in use. • If you leave the battery pack in the handset without charging it, the battery pack will be completely discharged. It may require several times of charging to recover to its full capacity.
Handset spare battery usage As only one battery pack is supplied with this unit, it is necessary to purchase an additional battery pack (optional) for use as a handset spare battery pack. lid of the base phone. 2 Insert the battery pack (with BP-T23 contacts facing down) into the battery compartment. Getting Started 1 Open the battery compartment 3 Close the battery compartment lid. The SPARE BATTERY lamp lights up. Charge the battery pack for more than 24 hours so that the battery is fully charged.
Step 4 Entering the area code When you use this phone for the first time, or move to an area that has a different area code, you must enter your home area code. Otherwise, you cannot use some functions of this phone and the Caller ID functions. This is also necessary because the phone must be able to select an area code to properly dial call from the Caller ID list. Depending on your region, enter 3-digit area code as follows: Case 1.
Notes • If the home area code is already entered, it appears on the display in step 4. To enter a different home area code, see “To change the home area code” below. • Do not allow more than 20 seconds to elapse between each step of the procedure. Getting Started Tips • You may press Jog Dial instead of (PGM) in step 6. • To check the current home area code, perform steps 1 to 4. The home area code appears on the display for about 20 seconds. To change the home area code Perform steps 1 to 4 on page 14.
Step 4: Entering the area code (continued) 5 Press Jog Dial. ”ENTER AREA CODE“ appears on the display. 6 Enter three digits of the local area code using the dialing keys. 7 Press (PGM). You will hear a long confirmation beep. Notes • If the local area code is already entered, it appears on the display in step 5. To enter a different local area code, see “To change the local area code” below. • Do not allow more than 20 seconds to elapse between each step of the procedure.
Identifying the parts Refer to the pages indicated in parentheses for details. Handset 1 Getting Started 2 0 3 4 5 qa qs qd qf 6 qg 7 8 9 qh qj qk 1 2 3 4 Antenna Speaker Jog dial (p. 14, 29, 41) TALK button (p. 20, 24) Lets you make or receive a call. 5 INTERCOM button (p. 36) Lets you talk by using the base phone and handset. 6 HOLD button (p. 20) Puts a call on hold. 7 Battery compartment (p. 11) 8 TONE button (p. 20) Allows you to switch temporarily to tone dialing.
Identifying the parts (continued) Base Phone 1 2 3 4 5 6 7 qs qd qf qg qh 8 9 qj qk ql w; wa ws 0 qa wd 1 Display window (p. 20, 26) 2 LINE lamp (p. 20, 24) Lights when the cordless handset is in use. 3 MESSAGES lamp (p. 49) Flashes when you have messages. 4 NEW CALL lamp (p. 41) Flashes when there is a “NEW” data in the Caller ID list. 5 Dialing keys (p. 22) 6 Battery compartment (p. 13) 7 TONE button (p. 20) Allows you to switch temporarily to tone dialing. 8 SPARE BATTERY lamp (p.
Getting Started wf wg qh REDIAL/PAUSE button (p. 23, 27) Redials the last number called/ inserts a pause in the dialing sequence. qj SPEED DIAL button (p. 26) Automatically dials the numbers programmed. qk DIAL MODE switch (p. 10) Selects pulse or tone dialing. ql RINGER LEVEL switch (p. 25) Adjusts the ringer volume. w; FLASH button (p. 25, 48) Switches to a second call if you have “call waiting” service, or lets you make a new call. wh wa INTERCOM button (p.
Basics Making calls 1 Pick up the handset from the base phone. 2 Press (TALK) and wait until VOL switch (HOLD) (REDIAL) (*TONE) (MUTING) “TALK” appears on the display. The display also shows the operation duration in hours, minutes and seconds. You will then hear a dial tone. “HANDSET IN USE” appears on the display of the base phone and the LINE lamp on the base phone lights up. If “CHANNEL SEARCHING” appears on the display, move closer to the base phone. 3 Dial the phone number.
Notes • When you increase the sound volume, in some cases the back ground noise may be increased as well. You should adjust the volume accordingly. • If your conversation is muted and “CHANNEL SEARCHING” appears on the display, move closer to the base phone; otherwise, the call will be disconnected after one minute. If the battery becomes weak during a call The handset will beep every three seconds five times and i and “BATTERY LOW” appears on the display. Finish your call and charge the battery pack.
Making calls (continued) Making calls through the speakerphone Press (SPEAKERPHONE) on the base phone. “SPEAKERPHONE” appears on the display and the display also shows the operation duration in hours, minutes and seconds. SPEAKERPHONE lamp The SPEAKERPHONE lamp lights up. Dial the phone number. To adjust the speaker volume, press (VOLUME)(+) or (--). Each press of (VOLUME)(+) or (--) switches the speaker volume by one of 8 levels.
Redialing 1 Press (TALK) and wait until “TALK” appears on the display. The LINE lamp on the base phone lights up. If you’re at the base phone, press (SPEAKERPHONE). “SPEAKERPHONE” appears on the display and the SPEAKERPHONE lamp lights up. 2 Press (REDIAL) to redial the last number dialed. If you’re at the base phone, press (REDIAL/PAUSE). Note If the number exceeds 32 digits or if it is erased, five short error beeps will alert you that the number cannot be redialed.
Receiving calls 1 When you hear the phone ring: (CALL WAITING/ FLASH) VOL switch (HOLD) • Press (TALK). or • Pick up the handset from the base phone when the handset is placed on the base phone. “TALK” appears on the display and the display also shows the operation duration in hours, minutes and seconds. “HANDSET IN USE” appears on the display of the base phone and the LINE lamp on the base phone lights up. 2 When you’re done talking, press (OFF) or replace the handset on the base phone.
If you have subscribed to the Caller ID service; • the caller’s number and/or name appears on the display when you receive a call (see page 40) or when another call comes in by “call waiting” service. • the ringer sound changes to a higher tone if the call matches the number stored on speed dialing keys or in the Phone Directory (memory match function; see page 40).
Telephone Features Speed dialing You can dial with a touch of a few keys by storing a phone number on a dialing key. Storing phone numbers and names Example: to store “SONY” “123-4567”. 1 Press (PGM). “PROGRAM” appears on the display. (VOLUME) 2 Press (SPEED DIAL). “ENTER 0 TO 9” appears on the display. 3 Press one of the dialing keys ((0) to (9)) to store a phone number on. (REDIAL/PAUSE) (SPEAKERPHONE) ENTER NAME You will hear a confirmation beep. 4 Enter the name using the dialing keys.
5 Press (PGM). “ENTER NUMBER” appears. 6 Enter the phone number. SONY 1234567 You can enter up to 32 digits, including a tone and a pause, each of which is counted as one digit. When the phone number of 17 digits or more has been entered , the phone number appears in two lines. 1234567890123456 12 7 Press (PGM). You will hear a long confirmation beep, and the name and the number are stored. The display goes off.
Speed dialing (continued) Making calls with speed dialing 1 2 3 Press (SPEAKERPHONE). Press (SPEED DIAL). Enter the desired speed dialing number ( (0) to (9)). The phone number stored as the speed dialing number will be dialed. To check the phone number before speed dialing When not making a call with the base phone, press (SPEED DIAL) and then one of the dialing keys ((0) to (9)). The number stored on the key appears on the display for five seconds.
Phone Directory You can dial a number by scrolling through the Phone Directory, in which up to 50 phone numbers can be stored. Storing phone numbers and names Example: to store “SONY” “123-4567”. Turn 1 Press (PGM). Press (Be sure not to press (TALK).) DIRECTORY AREA RINGER If “DIRECTORY” is not flashing, turn Jog Dial down to make it flash. 2 Press Jog Dial. “ENTER NAME” appears. 3 Enter the name using the dialing keys. You can enter up to 16 characters.
Phone Directory (continued) 4 Press (PGM). “ENTER NUMBER” appears. 5 Enter the phone number. SONY 1234567 You can enter up to 32 digits, including a tone and a pause, each of which is counted as one digit. When the phone number of 17 digits or more has been entered , the phone number appears in two lines. 1234567890123456 12 6 Press (PGM). You will hear a long confirmation beep, and the name and the number are stored. The display goes off.
Changing a stored name and/or phone number 1 Display the name and phone number you want to change by doing steps 1 and 2 in “Making calls from the Phone Directory” on page 32. SONY 1234567 2 Press Jog Dial. DIAL EDIT ERASE 1234567 3 Turn Jog Dial up to make “EDIT” flash and press Jog Dial. SONY 1234567 The cursor flashes at the last character of the name. 4 Turn Jog Dial down to erase the characters and enter the new name. 5 Press Jog dial.
Phone Directory (continued) Erasing a memory location SONY 1234567 1 Display the name and phone number you want to erase by doing steps 1 and 2 in “Making calls from the Phone Directory”. 2 Press Jog Dial. DIAL EDIT ERASE 1234567 3 Turn Jog Dial up to make “ERASE” flash and press Jog Dial. ERASE NO YES 1234567 4 Turn Jog Dial up to make “YES” flash, then press Jog Dial. You hear a long confirmation beep and the memory location is erased. Making calls from the Phone Directory 1 Press Jog Dial.
Tip You may press (TALK) to make a call instead of doing steps 3 and 4. About the search order The names appear in the following order when you turn Jog Dial up or down. t t • Alphabetical order: ABC...XYZ y symbols y * y # y 0 - 9 • Initial character: To search for “SONY” for example, press (7) and then turn Jog Dial to search through the names starting with P, Q, R, S or 7.
Setting the ringer type You can select a ringer type of the handset from four type. Turn Press 1 Press (PGM). 2 Turn Jog Dial up to make “RINGER” flash. DIRECTORY AREA RINGER 3 Press Jog Dial. The current ringer type appears. RINGER 1 SELECTED 4 Press one of the dialing keys ((1) to (4)) to select a ringer type. You will hear the corresponding ringer tone. 5 Press (OFF). Turning off the ringer of the handset 1 2 Perform steps 1 to 3 above. Press (0). You will hear a confirmation beep.
Switching the phones during a call You can easily switch between the handset and speakerphone on the base phone without disconnecting the call. To switch from the base phone to the handset 1 Press (HOLD) on the base phone. The call is on hold and “HOLD” appears on the display and the SPEAKERPHONE lamp on the base phone flashes. 2 Press (TALK) or (HOLD) on the LINE lamp SPEAKERPHONE lamp (SPEAKERPHONE) handset. You can continue talking to the caller through the handset. 1 Press (HOLD) on the handset.
Talking between the phones (Intercom) You can converse using the base phone and the handset. You can start the intercom from either phone. To talk from the handset to the base phone Press (INTERCOM) on the handset. (OFF) After the base phone rings twice, you will be connected automatically. When a person at the base phone answers, you can talk with each other. (TALK) (INTERCOM) “INTERCOM” appears on the display. When you are done talking Press (OFF) on the handset.
Notes • If there’s an incoming call while on the intercom, only the base phone rings. To answer the call, press (INTERCOM) on the base phone or handset. The intercom is canceled and you can talk to the outside caller. • While conversing with an outside caller via the base phone or handset, you cannot make an intercom call. If you press (INTERCOM), you will hear a busy tone. Tips • You can receive an intercom call on the handset even when “RINGER” is set to “RINGER OFF”.
Transferring a call You can transfer a call between the handset and base phone without disconnecting the call. To transfer from the base phone to the handset 1 Press (INTERCOM) to page the handset. The call is put on hold on the base phone and the handset rings. “** PAGING **” appears on the display of both the base phone and handset. 2 Press (INTERCOM) on the (SPEAKERPHONE) handset. “INTERCOM” appears on the display of both the handset and base phone.
To transfer from the handset to the base phone 1 Press (INTERCOM) to page the base phone. The call is put on hold on the handset. (TALK) After the base phone rings twice, you will be connected automatically. When a person at the base phone answers, you can talk with each other. “INTERCOM” appears on the display of both the base phone and handset. 2 Press (SPEAKERPHONE) on the “SPEAKERPHONE” appears on the display of the base phone. (SPEAKERPHONE) If no one answers the phone Press (TALK) on the handset.
Caller ID Features Understanding the Caller ID service Caller ID allows the caller’s phone number to be shown on the display before the call is answered. In order to use this feature, you must first subscribe to the Caller ID service. The name of this service may vary depending on your telephone company. To use this feature, be sure to enter your home area code (see page 14). When you receive a call The phone number appears on the display with the date and time* as shown in the following example.
Looking at the Caller ID list The phone stores the data of the last 20 calls received including “OUT OF AREA” and “PRIVATE” calls. It keeps track of all calls received; even if they were not answered. Viewing the Caller ID list You can look through the Caller ID list to check the phone number and/or name of the calls received on the handset’s display. Note that the display on the base phone shows the current caller’s phone number and/or name only, and you cannot view the caller ID list on the base phone.
Looking at the Caller ID list (continued) About the “*” mark SMITH JOHN * 1-201-123-4567 “*” appears if there are more than two calls from the same phone number. The older data will be replaced by the new data, so the calls are counted as only one call. Erasing data from the Caller ID list Old data will be erased automatically when a 21st call comes in, but you can also manually erase unnecessary data one by one or erase the entire list.
To erase the entire list at once 1 Display any Caller ID data. SMITH JOHN 1-201-123-4567 2 Press Jog Dial. DIAL PGM ERASE 1-201-123-4567 3 Turn Jog Dial up to make “ERASE” flash and press Jog Dial. ERASE NO YES ALL 1-201-123-4567 4 Turn Jog Dial up to make “ALL” flash, then press Jog Dial. ALL ERASE NO YES 1-201-123-4567 5 Turn Jog Dial up to make “YES” flash, then press Jog Dial. NEW OO OLD OO You will hear a long confirmation beep and the entire list is erased.
Using the Caller ID list By using the Caller ID list, you can call back a phone number from the Caller ID list easily, or store numbers from the Caller ID list into the Phone Directory. Calling back a number from the Caller ID list 1 Display the phone number you Turn Press want to call from the Caller ID list (see page 41). SMITH JOHN 1-201-123-4567 2 Confirm the number and press Jog dial. DIAL PGM ERASE 1-201-123-4567 3 Press Jog dial again. The phone automatically dials the displayed number.
Storing a number of the Caller ID list into the Phone Directory 1 Display the name and phone number you want to store from the Caller ID list (see page 41). 2 Confirm the number and press Jog Dial. 3 Turn Jog Dial up to make “PGM” flash and press Jog Dial. SMITH JOHN 1-201-123-4567 DIAL PGM ERASE 1-201-123-4567 SMITH JOHN 12011234567 The cursor flashes at the end of the name. Enter or change the name, if necessary (see page 31). 4 Press Jog Dial. The cursor flashes at the end of the phone number.
Using the Caller ID list (continued) To change the number of digits of the phone number If the number of digits of the phone number in the Caller ID list is different from the actual phone number, you need to adjust the number of digits of the phone number to call back or store into the Phone Directory. 1 While the phone number from the Caller ID list is displayed, press (#) repeatedly until the phone number with the correct number of digits appears on the display.
When the local area code matches 2 SMITH JOHN 201-123-4567 SMITH JOHN 1-123-4567 SMITH JOHN 1-201-123-4567 SMITH JOHN 123-4567 Continue the operation to call or store the phone number with the correct number of digits (pages 44 and 45). Notes • You need to adjust the number of digits each time you call back from the Caller ID list as the changes to the Caller ID data is not stored in memory. • You may not be able to change the number of digits depending on the Caller ID data.
Using “Caller ID with call waiting” service This telephone is compatible with the “Caller ID with call waiting” service. Make sure that your telephone company offers this service. Like the basic Caller ID service, you need to subscribe to “Caller ID with call waiting” in order to use this service. Even though you may have already subscribed to “Caller ID” and “call waiting” as two separate services, you need to request a subscription to “Caller ID with call waiting” as a single service.
Using visual message waiting service If you subscribe to your telephone company’s message service which includes this feature, the display will show that you have messages waiting to be retrieved. MESSAGES lamp If you have messages “MESSAGES WAITING” will appear on the display, and the MESSAGES lamp on the base phone flashes. The display and the MESSAGES lamp will go off when you retrieve your messages.
Using visual message waiting service (continued) If you move or change your telephone company Message waiting signals are sent in one of two ways: FSK signaling or “stutter” signaling (Your telephone company can provide you with more information about your service). The first time this phone receives a voice mail message, it will set itself to the FSK service and will lock out the stutter service if your telephone company is in FSK service.
Additional Information Mounting the base phone on a wall 1 1 Raise the hang-up tab. 2 Plug the telephone line cord to Hang-up tab the LINE jack and the AC power adaptor to the DC IN 9V jack, and hook the cords. Use the shorter cord for mounting. 3 Attach the wall bracket to the center of the base phone. Align the fmarks of the wall bracket with those of the base phone.
Notes on power sources On battery pack For the customers in the USA • Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for best performance. RECYCLING NICKEL-CADMIUM BATTERIES • If you do not use the handset for a long period of time, remove the battery pack from the handset after charging for more than 12 hours, and base phone after charging for more than 24 hours when you have a spare battery. This maintains battery life.
Troubleshooting Making calls If you’ve experienced any of the following difficulties while using your phone, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. Remedy You hear five short error beeps when you press (TALK). • Make sure you have set up the base phone correctly (page 8). • Move the handset closer to the base phone. You hear no dial tone.
Intercom Speed dialing/ Phone Directory During conversation Troubleshooting (continued) Symptom Remedy You hear interference during conversation. • Move the handset closer to the base phone. • Place the base phone away from noise sources (page 8). Your conversation is muted and “CHANNEL SEARCHING” appear on the display. • This is the out-of-range alarm. Move the handset closer to the base phone within one minute. • The battery is weak.
Caller ID Power source/battery Remedy The caller’s name and/or phone number does not appear on the display during call waiting. • Make sure you have subscribed to “Caller ID with call waiting” service (page 48). • Make sure nobody is talking with another phone on the same telephone line. You cannot dial the number from the Caller ID list. • Make sure you entered your home area code correctly (page 14). • You may need to change the number of digits of the phone number (page 46).
Specifications General Base phone Frequency band 902 - 928 MHz Operating channel 30 channels Dial signal Tone, 10 PPS (pulse) selectable Supplied accessories See page 7. Power source DC 9V from AC power adaptor AC-T122 Battery charging time Approx. 24 hours Dimensions Approx. 166 x 63 x 225 mm (w/h/d), antenna excluded (approx. 6 5⁄ 8 x 2 1⁄2 x 8 7⁄8 inches) Antenna: Approx. 120 mm (approx. 4 3⁄ 4 inches) Mass Approx. 595 g (approx.
Index A E, F, G R Adjusting volume handset volume 20, 24 speaker volume 22, 25 Area code 14 Erasing Caller ID data 42 last phone number dialed 23 local area code 16 Phone Directory 32 H Receiving calls 24 Redialing 23 Ringer RINGER LEVEL switch 25 setting the ringer type 34 turning on/off 34 Hold 20, 24 Home area code 14 S B Battery pack charging 11 duration 12 C Call waiting service 24, 48 Caller ID 40 Caller ID list 41 calling back 44 memory match function 40 storing in Phone Directory 45 Caller
Registro del propietario Los números de modelo y de serie se encuentran en la parte inferior del teléfono. Anote el número de serie en el espacio que se proporciona a continuación. Refiérase a estos números cada vez que se comunique con su distribuidor Sony con respecto al producto.
12. Desconecte este producto de la línea telefónica y refiera el servicio a personal de servicio calificado bajo las siguientes condiciones: A. Cuando el cable eléctrico o el enchufe se encuentra dañado o deshilachado. B. Si se ha derramado líquido dentro del producto. C. Si el producto ha estado expuesto a lluvia o agua. D. Si el producto no opera normalmente al seguir las instrucciones de operación.
6. La compañía telefónica puede realizar cambios en sus instalaciones, equipos, operaciones, o procedimientos que pueden afectar la operación del equipo. Cuando suceda esto, la compañía telefónica le avisará con antelación para que usted realice las modificaciones necesarias para mantener ininterrumpido el servicio. Nota 8. Todas las reparaciones deberá realizarlas un centro de reparaciones Sony.
Índice Preparativos 6 7 Lea esto en primer lugar Paso 1: Comprobación del contenido del paquete 8 Paso 2: Instalación del teléfono base 11 Paso 3: Preparación de la batería 14 Paso 4: Introducción del código de área 17 Identificación de las partes Operaciones básicas 20 Realización de llamadas 23 Repetición de la marcación 24 Recepción de llamadas Funciones del teléfono 26 Marcación instantánea 26 Almacenamiento de números de teléfono y nombres 28 Realización de llamadas con la marcación instantánea 29 D
Preparativos Lea esto en primer lugar Antes de utilizar su teléfono, tendrá que instalarlo. A continuación se indica la forma rápida de hacerlo: Pasos 1, 2, 3, y 4. Paso 1 (página 7) En primer lugar, desembale el teléfono y los accesorios suministrados. Paso 2 (páginas 8 a 10) A continuación, tendrá que hacer tres cosas para instalar el teléfono base, incluyendo la búsqueda del mejor lugar para el mismo.
Paso 1 Comprobación del contenido del paquete Compruebe si con el paquete ha recibido los elementos siguientes. Adaptador de alimentación de CA (AC-T122) Cables de línea telefónica (2) Teléfono base Soporte mural para el teléfono base Preparativos Si falta algo, póngase en contacto con su proveedor Sony.
Paso 2 Instalación del teléfono base Realice los pasos siguientes: • Elección del mejor lugar • Conexión del teléfono base • Elección del modo de marcación Elección del mejor lugar El lugar en el que coloque el teléfono base afectará la calidad de la recepción del microteléfono.
Conexión del teléfono base Si desea colgar el teléfono base de una pared, consulte la página 51. 3 Preparativos Enganche el cable. A un tomacorriente de CA A DC IN 9V 2 Adaptador de alimentación de CA (AC-T122 suministrado) A LINE 1 Cable de línea telefónica A la toma telefónica (suministrado) 1 Conecte el cable de la línea telefónica a la toma LINE y a una toma telefónica. 2 Conecte el adaptador de alimentación de CA a la toma DC IN 9V y a un tomacorriente de CA.
Paso 2: Instalación del teléfono base (continuación) Notas • Utilice solamente el adaptador de alimentación de CA AC-T122 suministrado. No utilice ningún otro adaptador de alimentación de CA. • Conecte el adaptador de alimentación de CA a un tomacorriente que suministre continuamente alimentación. • Coloque el teléfono base cerca del tomacorriente de CA a fin de poder desenchufar fácilmente el adaptador de alimentación de CA.
Paso 3 Preparación de la batería Antes de utilizar su teléfono, cargue la batería durante más de 12 horas. compartimiento de la batería del microteléfono. 2 Inserte la batería (con los BP-T23 Preparativos 1 Deslice y abra la tapa del contactos hacia abajo) en el compartimiento para la misma. 3 Cierre la tapa del compartimiento de la batería. 4 Coloque el microteléfono en el Lámpara CHARGE teléfono base. Usted podrá colocarlo con cualquier cara hacia arriba.
Paso 3: Preparación de la batería (continuación) Duración de la batería Una batería completamente cargada durará: • Aproximadamente 6 horas cuando utilice continuamente el microteléfono. • Aproximadamente 7 días con el microteléfono en el modo de espera. Notas • La batería se descargará gradualmente con el tiempo, incluso aunque no se utilice. • Si deja la batería en el microteléfono sin cargarla, se descargará completamente. Para que la batería recupere su plena capacidad, pueden requerirse varias cargas.
Utilización de una batería de repuesto para el microteléfono Como con esta unidad solamente se suministra una batería, tendrá que adquirir otra (opcional) para utilizarla de repuesto para el microteléfono. de la batería del teléfono base. 2 Inserte la batería (con los BP-T23 Preparativos 1 Abra la tapa del compartimiento contactos hacia abajo) en el compartimiento para la misma. 3 Cierre la tapa del compartimiento de la batería. La lámpara SPARE BATTERY se encenderá.
Paso 4 Introducción del código de área Antes de utilizar este teléfono por primera vez, o cuando se traslade a un lugar con código de área diferente, tendrá que introducir el código de su área. De lo contrario no podría utilizar ciertas funciones de este teléfono ni las de identificación de demandantes. Esto será necesario también porque el teléfono tendrá que poder seleccionar un código de área para marcar adecuadamente llamadas desde la lista de identificación de demandantes.
Notas • Si el código de área inicial ya está introducido, aparecerá en el visualizador en el paso 4. Para introducir un código de área diferente, consulte “Para cambiar el código de área inicial” indicado a continuación. • No deje que transcurran más de 20 segundos entre cada paso del procedimiento. Preparativos Sugerencias • En el paso 6, en vez del mando de lanzadera podrá presionar (PGM). • Para comprobar el código de área inicial actual, realice los pasos 1 a 4.
Paso 2: Introducción del código de área (continuación) 5 Presione el mando de lanzadera. En el visualizador aparecerá “ENTER AREA CODE”. 6 Introduzca los tres dígitos del código de área local utilizando las teclas de marcación. 7 Presione (PGM). Usted oirá un pitido largo de confirmación. Notas • Si el código de parea local ya está introducido, aparecerá en el visualizador en el paso 5. Para introducir un código de área local diferente, consulte “Para cambiar el código de área local” más abajo.
Identificación de las partes Con respecto a los detalles, consulte las páginas indicadas entre paréntesis. Microteléfono 1 Preparativos 2 0 3 qa qs qd qf 4 5 6 qg 7 8 9 qh qj qk 1 Antena 2 Altavoz 3 Mando de lanzadera (p. 14, 29, 41) 4 Botón de conversación (TALK) (p. 20, 24) Presiónelo para realizar o recibir una llamada. 5 Botón de intercomunicación (INTERCOM) (p. 36) Presiónelo para conversar entre el teléfono base y el microteléfono. 6 Botón de retención (HOLD) (p.
Identificación de las partes (continúa) Teléfono base 1 2 3 4 5 6 7 qs qd qf qg qh 8 9 0 qj qk ql w; wa ws qa wd 1 Visualizador (p. 20, 26) 2 Lámpara de línea (LINE) (p. 20, 24) Permanecerá encendida mientras esté utilizando el microteléfono inalámbrico. 3 Lámpara de mensajes (MESSAGES) (p. 49) Parpadeará cuando reciba mensajes. 4 Lámpara de nueva llamada (NEW CALL) (p. 41) Parpadeará cuando haya datos “NEW” (nuevos) en la lista de identificación de demandantes. 5 Teclas de marcación (p.
Preparativos wf wg qh Botón de repetición de marcación/pausa (REDIAL/PAUSE) (p. 23, 27) Presiónelo para volver a marcar el último número llamado/insertar una pausa en la secuencia de marcación. qj Botón de marcación instantánea (SPEED DIAL) (p. 26) Presiónelo para marcar automáticamente números almacenados. qk Selector de modo de marcación (DIAL MODE) (p. 10) Utilícelo para seleccionar la marcación por pulsos o por tonos. ql Selector de nivel del generador de llamada (RINGER LEVEL) (p.
Operaciones básicas Realización de llamadas 1 Tome el microteléfono del teléfono base. 2 Presione (TALK) y espere hasta que en el visualizador aparezca Selector VOL (HOLD) (REDIAL) (*TONE) (MUTING) “TALK”. El visualizador también mostrará la duración de la operación en horas, minutos, y segundos. Después oirá el tono de invitación a marcar. En el visualizador del teléfono base aparecerá “HANDSET IN USE” y se encenderá la lámpara LINE de dicho teléfono.
Notas • Si aumenta el volumen del sonido, en algunos casos es posible que aumente también el ruido de fondo. Ajuste adecuadamente el volumen. • Si la conversación se silencia y en el visualizador aparece “CHANNEL SEARCHING”, acérquese al teléfono base. De lo contrario, la llamada se desconectaría después de 1 minuto. Si la batería se debilita durante una llamada El microteléfono emitirá un pitido cada tres segundos, y en el visualizador aparecerán i y “BATTERY LOW”. Finalice su llamada y cargue la batería.
Realización de llamadas (continuación) Realización de llamadas a través del interfono Presione (SPEAKERPHONE) del teléfono base. Lámpara SPEAKERPHONE En el visualizador aparecerá “SPEAKERPHONE” y también mostrará el tiempo de operación en horas, minutos, y segundos. La lámpara SPEAKERPHONE se encenderá. Marque el número de teléfono. Para ajustar el volumen del altavoz, presione (VOLUME)(+) o (--). Cada vez que presione (VOLUME)(+) o (--), el volumen del altavoz cambiará en uno de 8 niveles.
Repetición de la marcación 1 Presione (TALK) y espere hasta que en el visualizador aparezca “TALK”. La lámpara LINE del teléfono base se encenderá. Si se encuentra en el teléfono base, presione (SPEAKERPHONE). En el visualizador aparecerá “SPEAKERPHONE” y se encenderá la lámpara SPEAKERPHONE. 2 Para repetir la marcación del último número marcado, presione (REDIAL). Operaciones básicas Si se encuentra en el teléfono base, presione (REDIAL/PAUSE).
Recepción de llamadas 1 Cuando suene el teléfono: (CALL WAITING/ FLASH) Selector VOL (HOLD) • Presione (TALK). o • Tome el microteléfono del teléfono base, si está en él. En el visualizador aparecerá “TALK” y también la duración de operación en horas, minutos, y segundos. En el visualizador del teléfono base aparecerá “HANDSET IN USE” y se encenderá la lámpara LINE. 2 Cuando termine de conversar, presione (OFF) o coloque el (MUTING) microteléfono en el teléfono base.
Si está subscrito al servicio de identificación del demandante; • el número y/o el nombre del demandante aparecerá en el visualizador cuando reciba una llamada (consulte la página 40) o cuando entre otra llamada con el servicio de “llamada en espera”. • el sonido del generador de llamada cambiará a un tono más alto si la llamada coincide con el número almacenado en las teclas de marcación instantánea, o en el directorio telefónico (función de correspondencia de memoria; consulte la página 40).
Funciones del teléfono Marcación instantánea Usted podrá marcar un número de teléfono presionando una tecla de marcación instantánea después de haber almacenado tal número en la misma. Almacenamiento de números de teléfono y nombres Ejemplo: para almacenar “SONY” “123-4567”. 1 Presione (PGM). En el visualizador aparecerá “PROGRAM”. (VOLUME) 2 Presione (SPEED DIAL). En el visualizador aparecerá “ENTER 0 TO 9”. 3 Presione una de las teclas de marcación ((0) a (9)) para almacenar un número de teléfono.
5 Presione (PGM). Aparecerá “ENTER NUMBER”. 6 Introduzca el número de teléfono. Usted podrá introducir hasta 32 dígitos incluyendo un tono y una pausa, que se contarán cada uno como un dígito. Cuando haya introducido un número de teléfono de 17 o más dígitos, tal número aparecerá en dos líneas. SONY 1234567 1234567890123456 12 7 Presione (PGM). Usted oirá un pitido largo de confirmación, y el nombre y el número se almacenarán. El visualizador se apagará.
Marcación instantánea (continuación) Realización de llamadas con la marcación instantánea 1 2 3 Presione (SPEAKERPHONE). Presione (SPEED DIAL). Introduzca el número de marcación instantánea deseado ((0) a (9)). El número de teléfono almacenado como número de marcación instantánea se marcará. Para comprobar el número de teléfono antes de la marcación instantánea Antes de realizar una llamada con el teléfono base, presione (SPEED DIAL) y después una de las teclas de marcación ((0) a (9)).
Directorio telefónico Usted podrá marcar un número desplazándose por el directorio telefónico, en el que podrá almacenar hasta 50 números de teléfono. Almacenamiento de números de teléfono y nombres Ejemplo: para almacenar “SONY” “123-4567”. Gire 1 Presione (PGM). Presione (No presione nunca (TALK).) DIRECTORY AREA RINGER Si “DIRECTORY” no está parpadeando, gire el mando lanzadera hacia abajo para hacer parpadee. 2 Presione el mando de lanzadera. Aparecerá “ENTER NAME”.
Directorio telefónico (continuación) 4 Presione (PGM). Aparecerá “ENTER NUMBER”. 5 Introduzca el número de teléfono. Usted podrá introducir hasta 32 dígitos, incluyendo un tono y una pausa, cada uno de los cuales se contará como un dígito. Cuando introduzca un número de teléfono de 17 o más dígitos, éste aparecerá en dos líneas. SONY 1234567 1234567890123456 12 6 Presione (PGM). Usted oirá un pitido largo de confirmación, y el nombre y el número se almacenarán. El visualizador se apagará.
Cambio de un nombre y/o un número de teléfono almacenado 1 Haga que se visualicen el nombre y el número de teléfono que desee cambiar realizando los pasos 1 y 2 de “Realización de llamadas desde el directorio telefónico” de la página 32. SONY 1234567 2 Presione el mando de lanzadera. DIAL EDIT ERASE 1234567 3 Gire el mando de lanzadera hacia arriba para hacer que parpadee “EDIT” y después presiónelo. SONY 1234567 El cursor parpadeará a la derecha del último carácter del nombre.
Directorio telefónico (continuación) Borrado de una ubicación de la memoria 1 Haga que se visualice el nombre y el número de teléfono que desee borrar realizando los pasos 1 y 2 de “Realización de llamadas desde el directorio telefónico”. 2 Presione el mando de lanzadera. DIAL EDIT ERASE 1234567 3 Gire el mando de lanzadera hacia arriba para hacer que parpadee “ERASE”, y después presiónelo.
Sugerencia Para realizar una llamada, en vez de ejecutar los pasos 3 y 4, podrá presionar (TALK). Acerca del orden de búsqueda Los nombres aparecerán en el orden siguiente cuando gire el mando de lanzadera hacia arriba o hacia abajo. t t • Orden alfabético: ABC...XYZ y símbolos y * y # y 0 - 9 • Carácter inicial: Para buscar “SONY” por ejemplo, presione (7) y después gire el mando de lanzadera para buscar a través de los nombres que comiencen por P, Q, R, S, o 7.
Ajuste del tipo de generador de llamada Usted podrá seleccionar entre cuatro tipos de generador de llamada del microteléfono. Gire Presione 1 Presione (PGM). 2 Gire el mando de lanzadera para hacer que parpadee “RINGER”. DIRECTORY AREA RINGER 3 Presione el mando de lanzadera. Aparecerá el tipo de generador de llamada actual. RINGER 1 SELECTED 4 Presione un a de las teclas de marcación ((1) a (4)) para seleccionar el tipo de generador de llamada.
Cambio de teléfono durante una llamada Usted podrá cambiar fácilmente entre el microteléfono y el interfono del teléfono base sin desconectar la llamada. Para cambiar del teléfono base al microteléfono 1 Presione (HOLD) del teléfono base. La llamada se pondrá en retención, en el visualizador aparecerá “HOLD”, y la lámpara SPEAKERPHONE del teléfono base parpadeará. Lámpara LINE Lámpara SPEAKERPHONE (SPEAKERPHONE) 2 Presione (TALK) o (HOLD) del microteléfono.
Conversación entre los teléfonos (intercomunicación) Usted podrá conversar utilizando el teléfono base y el microteléfono. La intercomunicación podrá iniciarse desde cualquier teléfono. Para hablar del microteléfono al teléfono base (OFF) (TALK) (INTERCOM) Presione (INTERCOM) del microteléfono. Después de que el teléfono haya sonado dos veces, usted se conectará automáticamente. Cuando la persona del teléfono base responda, ustedes podrán conversar. En el visualizador aparecerá “INTERCOM”.
Notas • Si entra una llamada durante la intercomunicación, solamente sonará el teléfono base. Para responder a la llamada, presione (INTERCOM) del teléfono base o del microteléfono. La intercomunicación se cancelará y usted podrá hablar con la persona del exterior. • Durante la conversación con el exterior a través del teléfono base o del microteléfono, no podrá realizar una llamada de intercomunicación. Si presiona (INTERCOM), oirá el tono de ocupado.
Transferencia de una llamada Usted podrá transferir una llamada entre el microteléfono y el teléfono base sin desconectarla. Para transferir del teléfono base al microteléfono 1 Presione (INTERCOM) para llamar al microteléfono. La llamada se pondrá en retención en el teléfono base y sonará el microteléfono. En el visualizador tanto del teléfono base como del microteléfono aparecerá “** PAGING **”. (SPEAKERPHONE) 2 Presione (INTERCOM) del microteléfono.
Para transferir del microteléfono al teléfono base 1 Presione (INTERCOM) para llamar al teléfono base. La llamada se pondrá en retención en el teléfono microteléfono. (TALK) Después de que el teléfono base haya sonado dos veces, usted se conectará automáticamente. Cuando la persona del teléfono base responda, ustedes podrán conversar. 2 Presione (SPEAKERPHONE) del teléfono base para hablar con quien llamó con el teléfono base. En el visualizador del teléfono base aparecerá “SPEAKERPHONE”.
Funciones de identificación del demandante Acerca del servicio de identificación del demandante El servicio de identificación de demandantes permitirá que el número de teléfono de quien llame aparezca en el visualizador antes de contestar a la llamada. Para utilizar esta función tendrá que abonarse primero a este servicio. El nombre de este servicio puede variar según la compañía telefónica. Para utilizar esta función, cerciórese de haber introducido su código de área inicial (consulte la página 14).
Comprobación de la lista de identificación de demandantes El teléfono almacena los datos de las últimas 20 llamadas recibidas, incluidas las de tipo “OUT OF AREA” y “PRIVATE”. Realiza un seguimiento de todas las llamadas recibidas, incluso si no se han contestado. Contemplación de la lista de identificación de demandantes Usted podrá observar la lista de identificación de demandantes para comprobar el número de teléfono y/o la lista de llamadas recibidas en el visualizador del microteléfono.
Comprobación de la lista de identificación de demandantes (continuación) Acerca de la marca “*” SMITH JOHN * 1-201-123-4567 La marca “*” aparecerá si hay más de dos llamadas del mismo número telefónico. Los datos más antiguos se reemplazarán por los más nuevos, forma por la que las llamadas se contarán solamente como una. Borrado de datos de la lista de identificación de demandantes Los datos antiguos se borrarán automáticamente cuando entre la 21.
Para borrar todos los datos a la vez 1 Haga que se visualicen los datos de identificación de usuarios. SMITH JOHN 1-201-123-4567 2 Presione el mando de lanzadera. DIAL PGM ERASE 1-201-123-4567 3 Gire el mando de lanzadera hacia arriba para hacer que parpadee “ERASE”, y después presiónelo. ERASE NO YES ALL 1-201-123-4567 4 Gire el mando de lanzadera hacia arriba para hacer que parpadee “ALL” y después presiónelo.
Utilización de la lista de identificación de demandantes Utilizando la lista de identificación de demandantes podrá devolver fácilmente la llamada a un número de teléfono de la lista de identificación de demandantes, o almacenar números de dicha lista en el directorio telefónico. Llamada a un número desde la lista de identificación de demandantes 1 Haga que se visualice el número Gire Presione de teléfono al que desee llamar desde la lista de identificación de demandantes (consulte la página 41).
Almacenamiento de un número de la lista de identificación de demandantes en el directorio teléfonico 1 Haga que se visualice el nombre y el número de teléfono que desee almacenar de la lista de identificación de demandantes (consulte la página 41). SMITH JOHN 1-201-123-4567 2 Confirme el número y presione el mando de lanzadera. DIAL PGM ERASE 1-201-123-4567 3 Gire el mando de lanzadera para hacer que parpadee “PGM”, y después presiónelo.
Utilización de la lista de identificación de demandantes (continuación) Para cambiar el número de dígitos del número de teléfono Si el número de dígitos del número de teléfono de la lista de identificación de demandantes es diferente al número de teléfono real, tendrá que ajustar dicho número de dígitos para poder llamar o almacenarlo en el directorio telefónico.
Cuando el código de área local coincida 2 SMITH JOHN 201-123-4567 SMITH JOHN 1-123-4567 SMITH JOHN 1-201-123-4567 SMITH JOHN 123-4567 Continúe la operación para llamar al número o para almacenarlo con el número correcto de dígitos (páginas 44 y 45). Notas • Usted no necesitará ajustar el número de dígitos cada vez que llame desde la lista de identificación de demandantes ya que los cambios de los datos de identificación de demandantes no se almacenarán en la memoria.
Utilización del servicio de “Identificación de demandantes con llamada en espera” Este teléfono es compatible con el servicio de “Identificación de demandantes con llamada en espera”. Compruebe si su compañía telefónica ofrece este servicio. Al igual que el servicio de identificación de demandantes, usted tendrá que abonarse a “Identificación de demandantes con llamada en espera” para poder utilizar este servicio.
Utilización del servicio de espera de mensajes visuales Si usted se abona al servicio de mensajes de su compañía telefónica que incluya esta función, el visualizador le indicará que usted tiene mensajes en espera de que los escuche. Lámpara MESSAGES Si posee mensajes En el visualizador aparecerá “MESSAGES WAITING”, y la lámpara MESSAGES del teléfono base parpadeará. Cuando haya escuchado sus mensajes, el visualiador y la lámpara MESSAGES se apagarán.
Utilización del servicio de espera de mensajes visuales (continuación) Si se traslada o cambia de compañía telefónica Las señales de mensaje en espera se transmitirán de dos formas: Señalización FSK o señalización de “tartamudeo” (su compañía telefónica podrá proporcionarle más información sobre este servicio).
Información adicional Montaje del teléfono base en una pared 1 1 Levante la lengüeta de colgado. 2 Enchufe el cable de la línea telefónica en la toma LINE y el Lengüeta de colgado adaptador de alimentación en la toma DC IN 9V, y enganche los cables. Utilice el cable más corto para el montaje. 3 Fije el soporte mural en el centro del teléfono base. Alinee las marcas f del soporte mural con las del teléfono base.
Notas sobre las fuentes de alimentación Batería Para clientes en EE.UU. • Para un óptimo rendimiento, almacene la batería a una temperatura de entre 5°C y 35°C. RECICLAJE DE PILAS DE NÍQUELCADMIO • Cuando no vaya a utilizar el teléfono durante mucho tiempo, extraiga la batería del microteléfono después de haberla cargado durante más de 12 horas, y la del teléfono base, y si está utilizando una batería de repuesto, después de más de 24 horas de carga. Esto prolongará la duración útil de las baterías.
Solución de problemas Síntoma Solución Se oyen cinco pitidos cortos de error al presionar (TALK). • Compruebe si ha instalado correctamente el teléfono base (página 8). • Acerque el microteléfono al teléfono base. No se oye el tono de invitación a marcar. • Compruebe si el cable de línea telefónica está conectado con seguridad a la toma telefónica. • Compruebe si la batería está completamente cargada (página 11). El teléfono no se conecta en absoluto, incluso aunque el número marcado es correcto.
Identificación de demandantes Intercomunicación Marcación instantánea/directorio Durante la conversación telefónico Solución de problemas (continuación) 54ES Síntoma Solución Se oyen interferencias durante la conversación. • Acerque el microteléfono al teléfono base. • Aleje el teléfono base de fuentes de ruido (página 8). La conversación se silencia y en • Ésta es la alarma de fuera de alcance. Acerque el microteléfono al teléfono base antes de un minuto.
Identificación de demandantes Fuente de alimentación/batería Solución El nombre y/o el número de teléfono del demandante no aparecen en el visualizador durante la función de llamada en espera. • Abónese al servicio de “Identificación de demandantes con llamada en espera” (página 48). • Cerciórese de que nadie esté hablando con otro teléfono a través de la misma línea. No es posible marcar un número desde la lista de identificación de demandantes.
Especificaciones Generales Teléfono base Banda de frecuencias 902 - 928 MHz Canales de operación 30 canales Señal de marcación Tonos y pulsos (10 pps), seleccionable Accesorios suministrados Consulte la página 7. Fuente de alimentación 9 V CC del adaptador de alimentación de CA AC-T122 Tiempo de carga de la batería Aprox. 24 horas Dimensiones Aprox. 166 x 63 x 225 mm (an/al/prf), excluyendo la antena Antena: Aprox. 120 mm Masa Aprox.
Índice alfabético A G, H O Ajuste del volumen volumen del interfono 22, 25 volumen del microteléfono 20, 24 Almacenamiento de datos en el directorio telefónico 45 Generador de llamada activación/desactivación 34 ajuste del tipo de selector de llamada 34 RINGER LEVEL selector 25 OUT OF AREA 40 B Batería carga 11 duración 12 Batería de repuesto 13 Borrado código de área local 16 directorio telefónico 32 datos de identificación de demandantes 42 último número marcado 23 C D, E Directorio telefónico 29
Sony Corporation Printed in China