Owners manual

ManualsBrandsSony ManualsProjectorVPL-VW90ES

VIDEO PROJECTOR

VPL-VW85

VPL-VW90ES

PROTOCOL MANUAL

1st Edition (Revised 1)

Summary of content (19 pages)

PAGE 1
VIDEO PROJECTOR VPL-VW85 VPL-VW90ES PROTOCOL MANUAL 1st Edition (Revised 1)
PAGE 2
! ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
PAGE 3
Table of Contents 1. Overview 1-1. Introduction ........................................................................ 1 1-2. Glossary of Terms .............................................................. 1 1-3. Protocol Stack Structure ..................................................... 1 2. Common Commands 2-1. Sub Commands .................................................................. 2 2-1-1. ITEM List ................................................................. 2 2-1-2.
PAGE 4
1. Overview 1-1. Introduction The projector is remotely controllable over RS-232C. It is useful for setting up the projector away from the operator. This protocol manual describes the specifications such as packet format and procedures for controlling the projector. In the following sections below, the term “CONTROLLER” is used as a device which controls the projector. CONTROLLER can be a PC or other specific device that is able to handle RS-232C. Although most of commands are available for both RS-232C.
PAGE 5
2. Common Commands 2-1. Sub Commands Sub Command is the value which is used by Simplified Command. Value is assigned for executing function. For example, if you want to change the picture mode, the appropriate value assigned for the desired picture mode should be chosen. 2-1-1. ITEM List Item list tables are described below. Tables are shown per function category.

PAGE 6

Item Number Remarks Data Item Upper byte Lower byte Data Byte Advanced Iris 00h 1Dh Off 0000h Manual 0001h Auto1 0002h Auto2 0003h Real Color Processing Film Mode Gamma Correction NR Block NR Mosquito NR 00h 00h 00h 00h 00h 00h 1Eh 1Fh 22h 25h 26h 27h Off 0000h User1 0001h User2 0002h User3 0003h Off 0000h Auto1 0001h Auto2 0002h Off 0000h Gamma 1 0001h Gamma 2 0002h Gamma 3 0003h Gamma 4 0004h Gamma 5 0005h Gamma 6 0006h

PAGE 7

Item Number Remarks Data Item Upper byte Lower byte Data Byte User Gain Red 00h 50h Set Value FFE2h to 001Eh (_30 to 30) User Gain Green 00h 51h Set Value FFE2h to 001Eh (_30 to 30) User Gain Blue 00h 52h Set Value FFE2h to 001Eh (_30 to 30) FFE2h to 001Eh (_30 to 30) User Bias Red 00h 53h Set Value User Bias Green 00h 54h Set Value FFE2h to 001Eh (_30 to 30) User Bias Blue 00h 55h Set Value FFE2h to 001Eh (_30 to 30) Iris Sensitivity 00h 56h Rec

PAGE 8

Table 2-3 ITEM List For Setup

Item Number Remarks Data Item Upper byte Lower byte Data Byte Input 00h 01h Video 0000h S Video Picture Muting 00h Input-A Signal Sel 30h 00h 32h Set/Get 0001h * Input A 0002h Component 0003h HDMI1 0004h HDMI2 0005h Off 0000h On 0001h Auto 0000h Computer 0001h Component 0002h Video GBR 0003h *1: VPL-VW85 only Table 2-4 ITEM List For 3D (VPL-VW90ES only) Item Number Data Remarks Item Upper

PAGE 9

Table 2-5 ITEM List For Status

Item Number Remarks Data Item Upper byte Lower byte Data Byte Status Error 01h 01h No Error 0000h Lamp Error 0001h Fan Error 0002h Cover Error 0004h Temp Error 0008h Status Power 01h D5V Error 0010h Power Error 0020h Temp Warning 0040h NVM Data Error 0080h Standby 0000h 02h Start Up 0001h Startup Lamp 0002h Power On 0003h Cooling1 0004h Cooling2 0005h Saving Cooling1 0006h Saving Cooling2 0007h Get only Sav

PAGE 10

2-1-2. Infrared Remote Command Code Tables are shown per function category. . 15 bit PROJECTOR: Table 2-7 to Table 2-10 . 20 bit PROJECTOR-E: Table 2-7 to Table 2-10 .

PAGE 11

Table 2-8 Infrared Remote Command Code For Screen CATEGORY Code Name 15 bit PROJECTOR 20 bit PROJECTOR-E 20 bit PROJECTOR-EE O _ _ 47 PITCH O _ _ 48 SHIFT _ O _ 60 APA _ O _ 61 PHASE _ O _ 62 LENS ZOOM _ O _ 63 LENS SHIFT _ O _ 64 LENS FOCUS _ O _ 6E WIDE MODE TOGGLE _ _ O 3E WIDE MODE WIDE ZOOM * _ _ O 3F WIDE MODE FULL1 * _ _ O 40 WIDE MODE FULL2 * _ _ O 41 WIDE MODE NORMAL * _ _ O 42 WIDE MODE FULL * _ _ O 43 WIDE MODE ZOOM * _

PAGE 12

Table 2-10 Infrared Remote Command Code For Installation CATEGORY 15 bit PROJECTOR 20 bit PROJECTOR-E _ O Code Name 00 V KEYSTONE + _ O 01 V KEYSTONE _ _ O 02 LENS SHIFT ← _ O 03 LENS SHIFT → _ O 3A V KEYSTONE _ O 78 LENS TOGGLE Table 2-11 Infrared Remote Command Code For HDMI Device Controll CATEGORY Code Name O 6E OPTIONS O 6F EXIT O 70 LINK MENU ON/OFF O 71 PLAY O 72 STOP O 73 PAUSE O 74 FAST REWIND O 75 FAST FORWARD O 76 PREVIOUS O 77 NEXT 20

PAGE 13

2-2. Reply

Item Number Data Item Data Upper byte Lower byte ACK Complete 00h 00h NAK Undefined Command 01h 01h Size Error 04h Select Error 05h Range Over 06h Not Applicable Check Sum Error Framing Error 0Ah F0h 10h 20h Parity Error 30h Over Run Error 40h Other Comm Error 50h Error description Check Sum Error A check sum error occurred. Framing Error A framing error occurred. Parity Error A parity error occurred. Over Run Error An overrun error occurred.

PAGE 14

3. RS-232C 3-1. Connection Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable. The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.

PAGE 15

3-3. Communication Procedure 3-3-1. Outline of Communication All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the command block format. Communication is started by the issue of a command at CONTROLLER and ended when the return data is sent to CONTROLLER after DEVICE receives the command. CONTROLLER is prohibited from sending several commands at one time.

PAGE 16

3-6. Command Block Format The block format of Simplified Command for RS-232C as shown in the Fig. 1-1. In this section, the block format for Simplified Command is provided. 3-6-1. Simplified Command [Send] The block format for sending request is shown below. B0 B1 B2 B3 B4 B5 START CODE [A9h] ITEM NUMBER Put the item number. Refer to the item list in the sections 2-1-1 and 2-1-2.

PAGE 17

3-7. Packet Examples 3-7-1. Change “Wide Mode” to “Zoom” START CODE = A9h ITEM NUMBER = 0020h (Wide Mode) SET/GET = 00h (SET) DATA = 0003h (Zoom) CHECK SUM = 23h END CODE = 9Ah You will receive the packet below if the process is successfully completed. START CODE = A9h ACK/NAK = 0000h (Complete) ACK = 03h DUMMY DATA = 0000h CHECK SUM = 03h END CODE = 9Ah There’s another way to realize the same purpose. There is “WIDE MODE TOGGLE” key on the infrared remote controller.

PAGE 18

The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.

PAGE 19

VPL-VW85 (CN) VPL-VW85 (J) VPL-VW85 (SY) VPL-VW85 (U) VPL-VW90ES (CN) VPL-VW90ES (J) VPL-VW90ES (SY) VPL-VW90ES (U) E 9-968-691-02 Sony Corporation Printed in Japan 2010.