User's Manual

ManualsBrandsSouthwing ManualsAudio EquipmentBluetooth Wireless Headset

USER GUIDE

® Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and

licensed to SouthWing.

* The features marked with an asterisk will only work with Bluetooth phones which

support the Hands-free profile. Today, most Bluetooth phones support this profile.

Note:

Please read the “Safe Usage Guidelines” and “Limited Warranty” before using the

headset.

INTRODUCTION

Thank you for choosing a SH240 Bluetooth® headset from SouthWing. This user guide

provides all the information you will need to use and care for your product. All relevant

information regarding your SouthWing product can be found in the support section of

our website: www.southwing.com

1. CHARGING THE HEADSET

You will need to charge the battery of your headset. To do so, follow these steps:

1. Plug the power supply into a power outlet.

2. Plug the connector of the power supply into the USB Charging Socket [1]. The

Indicator Light [2] will turn red to indicate the headset battery is charging.

3. Once the Indicator Light [2] turns off, the headset is fully charged and can be

removed from the power supply.

Please Note:

· The headset will not function while charging.

· If the Indicator Light [2] remains off while charging, the battery is already fully charged and does not

require further charging.

· To maximize battery life, do not charge the headset for extended periods of time.

· Full battery capacity will be achieved after two or three full charge/discharge cycles.

· When your battery is empty, it takes up to three hours to completely charge your headset.

2. PAIRING THE HEADSET

Auto-pairing

For added convenience, your headset has an auto-pairing function so that when you turn

the headset on for the first time, it is already in pairing mode. The Indicator Light [2]

will flash red and blue alternatively and a series of high tones can be heard. Follow

these steps to pair the headset with your mobile phone:

1. Put the mobile phone into pairing mode (reference your phone user manual). Ensure

that the mobile phone is no more than 3 feet (1meter) away from the headset.

2. Select the headset name “SouthWing SH240” from the list

3. Enter the PIN number: 0000

Now the headset and your mobile phone are paired and ready for hands free

communication through the Bluetooth connection.

To save battery you can disconnect the headset and your phone by pressing the Multi-

function button [2] three times. To re-connect them press the Multi-function button [2]

once.

Summary of content (8 pages)

PAGE 1
USER GUIDE ® Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and licensed to SouthWing. * The features marked with an asterisk will only work with Bluetooth phones which support the Hands-free profile. Today, most Bluetooth phones support this profile. Note: Please read the “Safe Usage Guidelines” and “Limited Warranty” before using the headset. INTRODUCTION Thank you for choosing a SH240 Bluetooth® headset from SouthWing.
PAGE 2
Normal pairing You will need to follow the steps below if you want to pair your headset with another mobile phone. 1. Ensure the headset is off. 2. Put the headset in pairing mode by pressing and holding the Multi-function button [2] for about 5 seconds until the Indicator Light [2] flashes red and blue alternatively and a series of high tones are heard. 3. Complete the normal pairing process by following steps 1, 2 and 3 in the auto-pairing section. 3.
PAGE 3
Accepting/rejecting* a call When the phone rings (the ring tone can be heard in the headset), briefly press the Multi-function button [2] once to accept the call. Alternatively, press and hold the Multi-function button [2] for 1 second to reject the call. Changing the volume To increase the volume during a call, press Vol+ button [3]. To decrease the volume, press the Vol- button [4]. The headset will remember previous volume settings each time it is turned on.
PAGE 4
ring tone and press the Multi-function button [2] once to select it and go back to standby mode. Battery Life To conserve battery life, your headset features an auto-sleep function. This function switches the headset off after 12 hours of inaction. Once your headset has entered autosleep, it can be switched on again normally. To check your battery level, press the Multi-function button [2] 4 times, and a series of beeps will indicate the talk time in hours (4 beeps indicates 4 or more hours of talk time).
PAGE 5
purchased it. Battery Care Your Headset battery will have a long life provided you follow these guide lines: · Do not use any accessory to charge your Headset other than the ones provided by SouthWing for this product. · Do not charge your Headset outdoors · Do not charge your Headset if the ambient temperature is above 45 degrees Celsius or below 10 degrees Celsius · Do not leave your Headset connected to the charger for extended periods of time, as excessive charging will reduce battery life.
PAGE 6
3. The free repair or replacement warranty does not cover failure of the product due to normal wear and tear, misuse, use contrary to the product user guide, accident, modification or adjustment, forces of nature, or damage resulting from contact with liquids. 4. Only service personnel who have been approved by SouthWing may repair this product. Attempted repair by anyone else will void this warranty. 5. At the discretion of SouthWing, a faulty unit will be either repaired or replaced.
PAGE 7
SouthWing 2655 LeJeune Rd. Suite 810 Coral Gables, FL. 33134 FAX :+ 1 305 442 1676 fcc_certifications@southwing.com To identify this product, refer to the Part, Series, or Model number found on the product. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
PAGE 8