SY-P4I845PE Motherboard **************************************************** mPGA Socket 478 Processor supported Intel 845PE AGP/PCI 400/533 MHz Front Side Bus supported ATX Form Factor **************************************************** User's Manual
SOYO™ SY-P4I845PE Copyright © 2002 by Soyo Computer Inc. Trademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyrights belong to their respective companies. Copyright Notice: All rights reserved. This manual has been copyrighted by Soyo Computer Inc.
SY-P4I845PE Table of Contents Table of Contents CHAPTER 1 MOTHERBOARD DESCRIPTION ............................... 1 1-1 INTRODUCTION ............................................................ 1 1-2 UNPACKING THE MOTHERBOARD ........................... 1 1-3 KEY FEATURES.............................................................. 2 1-4 HANDLING THE MOTHERBOARD ............................. 5 1-5 ELECTROSTATIC DISCHARGE PRECAUTIONS ....... 5 1-6 SY-P4I845PE MOTHERBOARD LAYOUT...............
SY-P4I845PE Table of Contents CHAPTER 6 USB 2.0 DRIVER INSTALLATION............................. 84 CHAPTER 7 HIGHPOINT HPT 371 DRIVER INSTALLATION . 85 CHAPTER 8 SERIAL-ATA DRIVER INSTALLATION.................
SY-P4I845PE Motherboard Description Chapter 1 MOTHEBOARD DESCRIPTION 1-1 INTRODUCTION The SY-P4I845PE AGP/PCI Motherboard is a high-performance Socket 478 processor supported ATX form-factor system board. SY-P4I845PE uses the Intel 845PE Chipset technology. This Motherboard is fully compatible with industry standards and adds many technical enhancements.
SY-P4I845PE Motherboard Description Warning: Do not unpack the Motherboard from its anti-static packaging until you are ready to install it. Like most electronic equipment, your Motherboard may be damaged by electrostatic discharge. To avoid permanent damage to components ground yourself while working by using a grounding strap. Otherwise, ground yourself frequently by touching the unpainted portion of the computer chassis to drain the static charges.
SY-P4I845PE Motherboard Description 1 x master AGP slot (1.5V only) 6 x 32-bit bus master PCI slots Enhanced IO Floppy disk controller 2x EIDE controllers with support for up to 4 Ultra DMA 33/66 /100 devices Standard/EPP/ECP parallel port 2x 16550 compatible serial ports IrDA compatible infrared port 6x USB2.
SY-P4I845PE Motherboard Description back on through the modem or RTC alarm through this function. This opens a lot of possibilities, such as remote access that switches the system on only after the modem receives a call. FAIL SAFE The SY-P4I845PE comes with added functionality to make managing the system easy and safe. Hardware Monitor The integrated Hardware Monitor IC and Hardware doctor software enables the user to monitor system voltages, temperatures and FAN speeds.
SY-P4I845PE Motherboard Description DDR RAM voltage select AGP voltage select On board Devices Enable/Disable Pre-defined optimal system Performance 1-4 HANDLING THE MOTHERBOARD To avoid damage to your Motherboard, follow these simple rules while unpacking: Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. Remove the Motherboard from its anti-static packaging. Hold the Motherboard by the edges and avoid touching its components.
SY-P4I845PE Motherboard Description 1-6 SY-P4I845PE MOTHERBOARD LAYOUT PS/2 KB PS/2 Mouse Connector Connector COM A +12V Power COM B ATX Power PRT USB 1_2 LAN Connector AOUT AIN J30 1 AMIC 2 AGAME 5 6 FJ1 PCI Slot #1 AC97 Audio JP5 CMOS Clear Jumper 3 PCI Slot #2 PCI Slot #3 CDIN1 1 4 IDE 1 AUXIN1 1 4 S_ATACN SATASEL PCI Slot #4 7 3 IDE 3 PCI Slot #5 ITE IT8712F-A PCI Slot #6 13 14 Back Panel IDE 2 DDR1 DDR2 DDR3 AGP Slot LAN DAVICOM DM9102AE USB20_1 SMCARDCN 1 2 FLP
SY-P4I845PE Motherboard Description 1-7 SY-P4I845PE MOTHERBOARD COMPONENTS A BC D E F GH I J K L AG M AF AE N O P AD AC Q R S AB T AA Z Y X W 7 V U
SY-P4I845PE Motherboard Description A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD AE AF AG +12V Power Connector CPU Cooling Fan1 Connector Davicom Lan Chip AGP Slot Socket 478 Connector Intel 845PE North Bridge Chip CPU FSB setting Jumper CPU Cooling Fan2 Connector DDR DIMM Bank CMOS Clear Jumper Intel 82801DB South Bridge Chip ATX Power Supply Connector Bus Mastering EIDE/ATAPI Ports Serial-ATA Chip Serial-ATA jumper Serial-ATA Connector IDE RAID Port HighPoint IDE RAID Chip Floppy Disk
SY-P4I845PE Hardware Installation Chapter 2 HARDWARE INSTALLATION Congratulations on your purchase of SY-P4I845PE Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti-static packaging until you have made the following preparations. 2-1 PREPARATIONS Gather and prepare all the following hardware equipment to complete the installation successfully: 1. Socket mPGA478 processor with built-in CPU cooling fan. 2.
SY-P4I845PE Hardware Installation Step3- Install expansion cards. Step4- Connect cables, case wires, and power supply. Step5- Power on and enter BIOS setup . Step6- Install supporting software tools. See Chapter 4 for more info. Warning: Turn off the power to the Motherboard, system chassis, and peripheral devices before performing any work on the Motherboard or system.
SY-P4I845PE Hardware Installation 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without forcing.
SY-P4I845PE Hardware Installation 4. Then close the socket handle to secure the CPU in place. Remember to connect the CPU Cooling Fan to the appropriate power connector on the Motherboard. The fan is a key component that will ensure system stability. The fan prevents overheating, therefore prolonging the life of your CPU. CPU Fan Installation Your Socket 478 processor kit comes with a cooling fan. Mount the fan on the processor according to the instructions provided by the manufacturer.
SY-P4I845PE Hardware Installation Step 2 Install Memory Module DDR1 DDR2 DDR3 This motherboard support PC2100 and PC2700, Non-ECC and non-registered module. The largest memory capacity possible is 2GB. On this motherboard, DRAM speed can be set independent from the CPU front side bus speed. A maximum of 2 pcs. Double-sided module can be used at the same time.
SY-P4I845PE Hardware Installation Memory Configuration Table DDR1 DDR2 DDR3 Double sided Double sided None Double sided Single sided None Double sided Single sided Single sided Single sided Single sided none Note: 533MHz FSB CPU should be used to have PC2700 support. Step 3 Connect cables, case wires, and power supply Install expansion cards This section tells how to connect internal peripherals and the power supply to the Motherboard.
SY-P4I845PE Hardware Installation Step 5 Connect cables, case wire, and power supply A. IDE Device Installation (HDD, CD-ROM) IDE2 Secondary IDE Pin1 IDE1 Primary IDE IDE 3 This Motherboard offers two primary and one secondary IDE device connectors (IDE1, IDE2), can support up to four high-speed Ultra DMA 33/66/100HDD or CD-ROM. IDE3 can support up to two high speed Ultra DMA 33/66/100/133 HDD.
SY-P4I845PE Hardware Installation 80-Conductor ATA 66/100 Flat Cable 1 40-pin 39 1 39 16
SY-P4I845PE Hardware Installation B. Floppy Drive Installation FDC Floppy Drive Connector Pin1 The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan. Connect one side of the 34-pin flat cable to the floppy drive and plug the other end to the floppy drive connector on the Motherboard. This Motherboard can support up to 1 floppy drives.
SY-P4I845PE Hardware Installation C. Front Panel Connections Power LED + _ 1 + 1 Reset Speaker KeyLock PWRBT + _ _ + ACPI LED HDD LED Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock header. Some systems may feature a KeyLock function with a front panel switch for enabling or disabling the keyboard. Connect the KeyLock switch to the 5-pin Keylock header on the Motherboard.
SY-P4I845PE Hardware Installation 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. Reset Pin Assignment Pin1 Pin2 Control PIN GND 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard. Speaker Pin Assignment _ + VCC Speaker out NC NC 4.
SY-P4I845PE Hardware Installation 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE1 or IDE2 (HDD, CD-ROM) device is active. HDD LED Pin Assignment Pin9 + _ Pin10 LED Cathode LED Anode 6. ATX Power On/Off Switch Attach the 2-pin momentary type switch to the PWRBT header for turning On or Off your ATX power supply. Note that 5VSB will always have power.
SY-P4I845PE Hardware Installation D. Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices. When connecting an external device, use the following figure to locate and identify which back panel connector to plug the device to.
SY-P4I845PE Hardware Installation 1. Onboard Serial Ports COM1/COM2 External peripherals that use serial transmission scheme include: - serial mouse, - modem. Plug the serial device cables directly into the COMA/COMB 9-pin male connectors located at the rear panel of the Motherboard. 2. Parallel Port PRT This parallel port is used to connect the printer or other parallel devices. Plug the parallel device cable into the 25-pin female connector located at the rear panel of the Motherboard. 3.
SY-P4I845PE Hardware Installation 5. Universal Serial Bus (USB20_0, USB20_1) This Motherboard provides three USB ports for your additional devices. Plug the USB device jack into the available USB connector USB20_0. - Standard device drivers come with the operating system for commonly used USB devices. USB20_1 is available. To make use of these USB ports, purchase a USB cable from your dealer.
SY-P4I845PE Hardware Installation E. Other Connections 1. Standard Infrared (SIRCON) Plug the 5-pin infrared device cable to the SIRCON header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications.
SY-P4I845PE Hardware Installation 2. Cooling Fan Installation (1) CPU Cooling Fan (CPUFAN1, CPUFAN2) After you have seated the CPU properly on the processor, attach the 3-pin fan cable to the CPUFAN connector on the Motherboard.
SY-P4I845PE Hardware Installation (2) Chassis Cooling Fan (CHAFAN1, CHAFAN2) Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector.
SY-P4I845PE Hardware Installation 3. Smart Card Reader 4. CD Line-in (CDIN1) This Motherboard provides one CD-Line in connectors. Please connect the 4-pin audio cable from your CD-ROM drive to either CDIN1.
SY-P4I845PE Hardware Installation 4. AUX-IN (AUXIN1) This Motherboard provides one AUX-IN connectors. Please connect the 4-pin audio cable from your CD-ROM drive to either AUX-IN. Please install according to the following pin assignment: AUXIN1 Pin Assigment 1 2 3 4 GND Left Right GND 5. MIC & LED Connector (J30) MIC & LED Connector (J30) Line_Out_L MIC IN LAN_LINK_LED 1 3 5 2 4 6 Line_Out_R GND VCC You can connect the Line-out /MIC in/LAN LED to the front panel of your PC case.
SY-P4I845PE Hardware Installation F. ATX12V Power Supply The ATX12V power supply includes a 20-pin ATX connector that comply with the ATX specification, Version 2.03 for M/B specification, a new 4-pin receptacle/header combination--the +12V power connector--has been defined. The presence of the +12V power connector indicates that a power supply is ATX12V; the absence of the +12V power connector indicates that a supply is ATX.
SY-P4I845PE Hardware Installation The Motherboard requires a power supply with at least 350 Watts and a "power good" signal. Make sure the ATX power supply can take at 1.5 A max current * load on the 5V Standby lead (5VSB) to meet the standard ATX specification. * Note: If you use the Wake-On-LAN (WOL) function, make sure the ATX 12V power supply can support at least 720 mA on the 5V Standby lead (5VSB).
SY-P4I845PE Hardware Installation G. CMOS Clear (JP5) In some cases the CMOS memory may contain wrong data, follow the steps below to clear the CMOS memory. 1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper can be easily identified by its white colored cap. 2. Then put the jumper back to 1-2 to allow writing of new data into the CMOS memory.
SY-P4I845PE Hardware Installation Audio Upgrade The standard configuration of the P4I845PE motherboard supports 2 or 4-channel audio. Step 5 Power On You have now completed the hardware installation of your Motherboard successfully. 1. Turn the power on 2. To enter the BIOS Setup Utility, press the key while the system is performing the diagnostic checks, Note: If you have failed to enter the BIOS, wait until the boot up sequence is completed.
SY-P4I845PE Hardware Installation Repeat this operation until you get the following screen. 3.
SY-P4I845PE Hardware Installation prompt to load the BIOS optimal setup. Step3. Select [SOYO COMBO FEATURE] Do this step if you want to change or overclock the CPU FSB. Set the [CPU Frequency Select] field to “Manual”, to be able to change the CPU frequency 1 MHz stepping. Step4. Select [SAVE & EXIT SETUP] Press to save the new configuration to the CMOS memory, and continue the boot sequence.
SY-P4I845PE BIOS Setup Utility Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
SY-P4I845PE BIOS Setup Utility Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command F1 General Help F10 Previous Values Load Fail-Safe Defaults Load Optimized Defaults Save [Esc] Exit F5 F6 F7 [Enter] Select [+/–/PU/PD Value ] Description Gives the list of options available for each item. Restore the old values. These are the values that the user started the current session with. Loads all items with the most conservative values.
SY-P4I845PE BIOS Setup Utility SAVE AND EXIT SETUP Select the [SAVE & EXIT SETUP] option from the Main Menu to save data to CMOS and exit the setup utility. This option saves all your changes and causes the system to reboot. R O M C M O S A W A R D S T A N D A R D B IO S C H IP S E T P O W C M O S F E A T U R E S E R P C I/ IS A B IO S S E T U P U T IL IT Y S O F T W A R E , IN C .
SY-P4I845PE BIOS Setup Utility 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO Feature]. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will display on screen.
SY-P4I845PE BIOS Setup Utility The [SOYO COMBO Feature] menu combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS. 3-1.1 System Performance Setting Description Note System Normal Performance Fast Turbo Adjust your system’s memory timing. Default CPU Clock Auto Manual Set the field to “Manual” to overclock the Default CPU frequency by 1MHz stepping.
SY-P4I845PE BIOS Setup Utility Setting Auto Detect Disabled PCI Clk Description Note Disables any clock signals on not Default used PCI slots. For EMI purposes. Enabled Spread Spectrum Disabled 0.35% 0.50% 0.75% 1.00% Modulates the clock signal on the Default CPU. For EMI purposes. 3-1.2 CPU Vcore Select Setting Description Note CPU Vcore Select Default This function adjust Default 1.100V, 1.125V, 1.150V, the CPU voltage. 1.175V, 1.200V, 1.225V, 1.250V, 1.275V, 1.300V, 1.325V, 1.350V, 1.375V, 1.
SY-P4I845PE BIOS Setup Utility 3-1.3 Advanced DRAM Control Setting Description DRAM Timing Selectable By SPD Manual If enable the DRAM will auto detect the DRAM timing. CAS Latency Time 1.5 2 2.5 3 This item allows you to control the DRAM CAS Latency time. Note Default Default 5 Active to Percharge Delay 6 7 This item allows you to control the DRAM Percharge Delay time. Default DRAM RAS# to 2 CAS# Delay 3 This item allows you to control DRAM RAS to CAS delay time.
SY-P4I845PE BIOS Setup Utility 3-1.5 Onboard Settings Setting Note Disabled This item allows you write-protect your BIOS chip from virus. If you want to flash your BIOS, set this option to disabled Default Onboard IDE RAID Enabled Disabled This item allow you to control Onboard IDE RAID. Onboard LAN Enabled Disabled This item allows you to control Default Onboard LAN. Disabled Auto This item allow you to control Onboard Audio. C.I.H. 4-WAY Protection AC97 Audio Enabled Description 3-1.
SY-P4I845PE BIOS Setup Utility 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. CMOS Setup Utility – Copyright ( C ) 1984-2002 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Mon, May 7 2001 2 : 30 : 20 Item Help Menu Level IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave None None None None Change the day, month, year and century. Drive A Floppy 3 Mode Support 1.44M, 3.5 in.
SY-P4I845PE BIOS Setup Utility 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary Setting Description Note (Secondary) Master & Slave IDE HDD Auto-Detection Press Enter To auto-detect the HDD’s size, head… on this channel IDE Primary Slave (User Type) Auto BIOS detects hard disk type Default automatically. User defines the type of hard disk. Access Mode Auto User None CHS LBA Large BIOS detects hard disk mode automatically.
SY-P4I845PE BIOS Setup Utility 3-2.4 Others Optional Setting Description Note Video EGA/VGA CGA 40 CGA 80 MONO (Monochrome) Select the video mode. Halt On ALL Errors No Errors All, But Keyboard All, But Diskette All, But Disk/Key When the BIOS detects system Default errors, this function will stop the system. Select which type of error will cause the system halt.
SY-P4I845PE BIOS Setup Utility 3-3 ADVANCED BIOS FEATURES Select the [Advanced BIOS Features] option from the Main Menu and press [Enter] key.
SY-P4I845PE BIOS Setup Utility 3-3.1 Virus Warning Setting Description Allows you to choose the Enabled VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. 3-3.2 Cache Memory Options Setting Description Virus Warning Disabled CPU L1 & L2 Cache CPU L2 Cache ECC Checking Disabled Enabled Enables the CPU's L1 & L2 cache.
SY-P4I845PE BIOS Setup Utility 3-3.4 Boot Up Floppy Seek Setting Boot Up Floppy Disabled Seek Enabled Description Seeks disk drives during boot up. Disabling speeds boot up. Default 3-3.5 Boot Up NumLock Status Setting Boot Up NumLock Status On Off Normal Fast Description Note Puts numeric keypad in Default NumLock mode at boot-up. Puts numeric keypad in arrow key mode at boot-up. 3-3.6 Gate A20 Options Setting Gate A20 Options Note Description A pin in the keyboard controller controls GateA20.
SY-P4I845PE BIOS Setup Utility Typematic Settings Typematic Rate Setting Description Note 6 (Char/sec) Choose the rate at which a Default 8 (Char/sec) character is repeated when 10 (Char/sec) holding down a key. 12 (Char/sec) 15 (Char/sec) 20 (Char/sec) 24 (Char/sec) 30 (Char/sec) 250 (msec) Choose how long after Default 500 (msec) you press a key down the 750 (msec) character begins 1000 (msec) repeating. 3-3.8 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup.
SY-P4I845PE BIOS Setup Utility HDD S.M.A.R.T. Capability Enabled Disabled Report No FDD Yes For WIN 95 No Enabled this field when your HDD supports the S.M.A.R.T. function. Consult your HDD provider for details. Default Windows will release IRQ line 6 (normally used by the Floppy Disk Drive) after you disable your on-board FDD and set this field to [Yes]. Windows will reserve INT 6 for Default your FDD, whether it is disabled or not.
SY-P4I845PE BIOS Setup Utility 3-4 ADVANCED CHIPSET FEATURES Caution: Change these settings only if you are already familiar with the Chipset. The [Advanced Chipset Features] option changes the values of the chipset registers. These registers control the system options in the computer.
SY-P4I845PE BIOS Setup Utility 3-4.1 CHIPSET FEATURES SETUP CHIPSET Setting Description FEATURES Note System BIOS Disabled Cacheable Enabled The ROM area F0000H-FFFFFH is cacheable. Default Video BIOS Cacheable Disabled Enabled The video BIOS C0000H-C7FFFH is Default cacheable. Delayed Transaction Disabled This item allows you to control Delay Default Transaction for thermal temp.
SY-P4I845PE BIOS Setup Utility 3-5 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer. The following screen shows setup default settings.
SY-P4I845PE BIOS Setup Utility The following tables describe each field in the INTEGRATED PERIPHERALS Menu and provide instructions on how to configure the IDE controls, FDC controls, and the onboard serial and parallel ports. 3-5.
SY-P4I845PE BIOS Setup Utility 3-5.2 Keyboard Controls Keyboard Controls Setting Description USB Controller Disabled Enabled Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals. USB 2.0 Controller Disabled Select Enabled if you have USB Enabled 2.0 peripherals. Note Default Default USB Keyboard Support Disabled Select Enabled if you want to use Default Enabled USB Keyboard in DOS.
SY-P4I845PE BIOS Setup Utility 3-5.4 Others Optional Setting Description POWER ON Password Function Hot KEY Mouse Move Mouse Click Any KEY Note Enables you to wake-up the system by entering a password at the keyboard. You can wake-up the system by pressing the key combination of your choice (Ctrl-F1~F12). Enables waking up the system by pressing either the right or left mouse button. BUTTON-ONLY Disables the Wake-Up by Keyboard function.
SY-P4I845PE BIOS Setup Utility 3-5.6 Onboard Serial Ports Onboard Serial Setting Description Ports Onboard Serial Port 1 / Serial Port 2 Disabled 3F8/IRQ4 Choose serial port 1 & 2's I/O address. 2F8/IRQ3 Do not set port 1 & 2 to the same setting except for Disabled 3E8/IRQ4 or Auto. 2E8/IRQ3 Auto Note Default (port 1) Default (port 2) The second serial port offers Default several special modes. It can either work as an infrared device (IrDA, ASKIR) or as a Smart Card reader (SCR).
SY-P4I845PE BIOS Setup Utility 3-5.8 Others Optional Setting PWRON After PWR-Fail On Off Former-Sts Game Port Address Disabled 201 209 Midi Port Address Disabled 330 300 Description Note The system will switch on when power comes back after a power failure. The system will remain off Default when power comes back after a power failure. The system will return to the state it was in before the power failure when power returns. (i.
SY-P4I845PE BIOS Setup Utility 3-6 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions.
SY-P4I845PE BIOS Setup Utility 3-6.1 Power Management Controls Power Setting Description Management Controls ACPI Suspend S1(POS) Type S3(STR) S1 & S3 This item allows you select suspend mode. Note Default Run VGABIOS if S3 Resume Auto Yes No Some OS (win xp/2k) require Default to load VGABIOS after resume from S3. Power Management User Define Lets you define the HDD and Default system power down times.
SY-P4I845PE BIOS Setup Utility Power Management Controls (Continued) Power Setting Description Management Controls Note HDD Power Down Disabled 1-15Min Soft-Off by PWR-BTTN Instant-off Turns off the system power instant after pushing the power button. Delay 4 Turns off the system power 4 Sec. seconds after pushing the power button. Default Wake-Up by PCI card Disabled Default When the set time has elapsed, BIOS sends a command to the HDD to power down. This turns off the HDD motor.
SY-P4I845PE BIOS Setup Utility 3-6.2 Reload Global Timer Events Power Down Setting Description & Resume Events IDE0, IDE1 Primary Secondary Disabled Enabled FDD, COM, LPT Port Disabled Enabled PCI PIRQ [A-D]# Disabled Enabled Note Default In effect, the system remains alert for anything which occurs to a device which is configured as Enabled. Default In effect, the system remains alert for anything which occurs to a device which is configured as Enabled.
SY-P4I845PE BIOS Setup Utility 3-7 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots.
BIOS Setup Utility SY-P4I845PE 3-7.1 PNP/PCI Configuration Controls PNP/PCI Setting Description Controls Note Reset Configuration Data Disabled Retain PnP configuration Default data in BIOS. Enabled Reset PnP configuration data in BIOS. Resources Controlled By Manual BIOS does not manage PCI/ISA PnP card IRQ assignment. Requires to assign IRQ-# and DMA-# to PCI or ISA PnP manually.
SY-P4I845PE BIOS Setup Utility PNP/PCI Configuration Setup (Continued) PNP/PCI Setting Description Setup Note Interrupt Line IRQ 15 IRQ 14 How to set the BIOS to release the IRQ to the PnP Interrupt pool: PnP / PCI configuration Integrated Peripherals IRQ 15: PCI / ISA PnP On-Chip Secondary PCI IDE: disabled IRQ 14: PCI / ISA PnP On-Chip Primary PCI IDE: disabled Interrupt 12 will be released by the PnP IRQ 12 IRQ 12: PCI / ISA PnP BIOS automatically if the PS/2 Mouse Port is not used.
SY-P4I845PE BIOS Setup Utility 3-8 PC HEALTH STATUS This option sets the Motherboard's PC Health Status. CMOS Setup Utility – Copyright ( C ) 1984-2002 Award Software PC Health Status Shutdown Temperature CPU Vcore 3.3V +5V +12V DRAM Voltage AGP Voltage CHA Temperature CPU Temperature CHAFAN1Speed CPUFAN1 Speed Move Enter:Select F5:Previous Values Disabled 1.72 V 3.21 V 5.02 V 11.77 V 2.59 V 1.
SY-P4I845PE BIOS Setup Utility 3-8.1 CPU Device Monitoring CPU Device Setting Description Monitoring Shutdown Temperature Disabled 50°C/122°F, 55°C/131°F, 60°C/140°F, 65°C/149°F, 75°C/167°F, 80°C/176°F Note This item allows you to set up Default the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode. Show the current voltage status. +3.3V, +5V, +12V, DRAM Voltage, AGP Voltage, CPU Vcore V CHA Temperature °C/°F Show the current status of the system temperature.
SY-P4I845PE BIOS Setup Utility 3-9 LOAD FAIL-SAFE DEFAULTS Select the [Load Fail-Safe Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
SY-P4I845PE BIOS Setup Utility 3-10 LOAD OPTIMIZED DEFAULTS Select the [Load Optimized Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
SY-P4I845PE BIOS Setup Utility 3-11 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [Advanced BIOS Feature] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1. Choose [Advanced BIOS Feature] in the Main Menu and press [Enter]. Select the [Security Options] item and set the field to: a.
SY-P4I845PE BIOS Setup Utility 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: Confirm Password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu. This diagram outlines the password selection procedure: Type Typethe thePassword Password and Press: Press: ROM PCI/ISA BIOS Press without ↔ Press: the password entering ↔ CMOS SETUP UTILITYWithout entering password AWARD SOFTWARE, INC.
SY-P4I845PE BIOS Setup Utility Boot Menu Boot Menu enables user to boot-up on different boot device without going into the BIOS setup. To enable boot Menu, press “ESC” after memory initialization, user will see a device menu, in which user can choose on which device they wish to boot from.
SY-P4I845PE Drivers installation Chapter 4 DRIVERS INSTALLATION The SOYO-CD will Auto Run only in Windows Base Operating System. Your SY-P4I845PE Motherboard comes with a CD-ROM labeled “SOYO CD”. The SOYO CD contains a. The user’s manual for your new motherboard in PDF format, b. The drivers software available for installation, and c. A database in HTML format with information on SOYO motherboards and other products. Step 1.
SY-P4I845PE Drivers installation The user's manual files included on the SOYO CD are in PDF (Postscript Document Format). In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system. Note: The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and otherwise prompts you on whether or not you want to install it. You must install the Acrobat Reader utility to be able to read the user's manual file.
SY-P4I845PE Drivers installation Step 2. Install Drivers and Utilities Drivers that are needed to install for the system to operate properly 1. Intel Chipset Software Installation Utility for Win 98/98SE/ME/NT/XP 2. C-Media 8738 audio driver 3. HighPoint Utility for the on-board RAID function The rest of the available driver is optional. Highlight the driver you want to install and then click ok. The Start Up program displays the drivers available for the particular model of Motherboard you own.
SY-P4I845PE Drivers installation the IDE sub-system and overall system performance. Several components will be available only on Pentium(R) 4 processor-based systems running Microsoft Windows 2000 Professional. Software installation is flexible and fully automated for Microsoft Windows 98, Windows 98 Second Edition(SE),Windows 98 Millennium Edition(Me), Windows NT4.0, and Windows 2000 operating systems. C-MEDIA Audio Driver/Application for Win 9x/ME/2000/NT/XP 1.
SY-P4I845PE Drivers installation Select which driver you want to install and click OK, or click Cancel to abort the driver installation and return to the main menu. Note : Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require restart or your system before they become active. Step 3.
SY-P4I845PE Drivers installation After Windows XP installation, your device manager should look like this: 78
SY-P4I845PE Drivers installation After driver installation, your Windows XP device manager should look like this: Note: To install the USB 2.
SY-P4I845PE Drivers installation Drivers directory list in the CD driver 80
SY-P4I845PE Davicom Onboard LAN Driver Chapter 5 DAVICOM ONBOARD LAN DRIVER INSTALLATION Installing the Davicom Onboard LAN Drivers under Windows 98SE 1. Move the cursor to my computer icon. 2. Click mouse right button then select “properties”. 3. Click “Device Manager”, then click “other devices”. 4. Select “PCI Ethernet Controller”, then Double click it. 5. You will see the “Driver” item above this windows, then click it. 6. Click on “Update Driver”. 7. Click on “Next”. 8.
SY-P4I845PE Davicom Onboard LAN Driver 8. Select the following directory. 9. The directory is in SOYO CD:” D:\LAN\Davicom” (where D: is your CD-ROM) and click ok. 10. After informing windows of the driver directory the driver will be installed Restart your system after installation. Installing the Davicom Onboard LAN Drivers under Windows NT 1. Double click the Network icon in the control panel then click “Yes”. 2. Click on “Next”. 3. Click on “Select from list”. 4. Click on “Have Disk”. 5.
SY-P4I845PE Davicom Onboard LAN Driver Installing the Davicom Onboard LAN Drivers under Windows XP (Windows XP can detect Davicom LAN driver automatic, so this installation is to update the LAN driver) 1. Move the cursor to the computer icon. 2. Press mouse right button select “properties”, then click it. 3. Click “Hardware”, then click Device Manager”. 4. Double click “Network adapter”. 5. Double click “DAVICOM 9102-Based PCI Fast Ethernet Adapter”. 6. Click “Driver” 7.
SY-P4I845PE USB 2.0 Driver Installation Chapter 6 USB 2.0 DRIVER INSTALLATION For Windows 2000 and Windows XP USB 2.0 Drivers are available for download using Windows Update for both Windows XP and Windows 2000. For additional information regarding USB 2.0 support in Windows XP and Windows 2000, please visit http://www.microsoft.com/hwdev/bus/USB/default.
HighPoint hpt371 Driver Installation SY-P4I845PE Chapter 7 HIGHPOINT HPT371 DRIVER INSTALLATION Installing Driver on an Existing System 9x/ME Manual Installation If Windows can not find new hardware, the driver can be installed through the following steps: 1. Shut down all programs. 2. Click Start-->Setup-->Control Panel, then double-click on Add New Hardware icon. 3. Click Next in the popup window to continue. 4. A dialog box will appear and ask whether to let windows search for new hardware.
HighPoint hpt371 Driver Installation SY-P4I845PE button. 3. In the next window, select Have Disk.... 4. Insert the SOYO driver CD and type in the path the driver CD of D:\Raid\Hpt371\121\WinNT, then click OK. 5. In the next window, select the HPT371 UDMA/ATA133 Controller item, then click OK. 6. Follow the system prompt to install the driver. When finished, re-start the computer. Windows 2000 1. Click Start-->Setup-->Control Panel --> Switch to classic View system hardware device manager. 2.
HighPoint hpt371 Driver Installation SY-P4I845PE 6. Check “search removable media …..” and then click next 7. Choose the driver for Win XP 8. During installation, Win XP will prompt you to insert the RAID driver diskette 9. Browse to the directory that contains the missing file (D:\raid\hpt371\121\Winxp). If you click yes without browsing, Win XP will not find the .inf file 10. Follow the system prompt to finish the installation, and restart the computer.
HighPoint hpt371 Driver Installation SY-P4I845PE NT4.0. Install driver during Windows 2000 installation 1. Go to “D:\raid\hpt371\121\” directory, (assuming that your CD-ROM is drive d) copy all the files and directories to a floppy disk. 2. If Windows 2000 is installed from the floppy drive, please let the installing program run automatically.
HighPoint hpt371 Driver Installation SY-P4I845PE the F6 Key. 3. Press the S key to specify additional devices when the Windows XP Setup window appears. 4. The system will ask whether to install the driver under WinNT or under Windows XP, please select to install the driver under Windows XP. 5. Insert the floppy disk of the driver, then press Enter to continue. 6. In the next window (Device Type), please select HPT371 UDMA/ATA133 Controller for Windows XP to continue. 7.
SY-P4I845PE Serial-ATA Driver Installation Chapter 8 SERIAL-ATA DRIVER INSTALLATION Win 98SE/2000/XP installation The Serial-ATA chip will be automatically detected after installing the Highpoint 371 driver.
91
