Z100 / Z300 Z500 Z700 OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW ELLIPTICAL!
Table of Contents Product Registration…………………………………………………………………………. 2 Important Safety Instructions………………………………………………………………… 3 Important Electrical Information………………………………………………………………4 Important Operation Instructions……………………………………………………………..4 Assembly Instructions………………………………………………………………………….5 Transport………………………………………………………………………………………...8 Operation of Your New Elliptical………………………………………………………………8 Manufacturer’s Limited Warranty……………………………………………………………..
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come.
Important Safety Instructions WARNING - Read all instructions before using this appliance. ■ Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet and elliptical may result. ■ Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. ■ Keep hands away from all moving parts. ■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly, call your dealer.
Important Electrical Information WARNING! ● NEVER remove any cover without first disconnecting AC power supply. ● If voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. ● NEVER expose this elliptical to rain or moisture.
Assembly Instructions ASSEMBLY PACK CHECK LIST ■ ■ ■ ■ ■ 5/16" x 1/2" Button Head Socket Screw (12pcs) 3/8" x 2" Thumb Head Socket Screw (2pcs) M6 x 25 m/m Button Head Socket Screw (8pcs) 6 x14 x1T Flat Washer (8pcs) Combination M5 Allen Wrench & Screwdriver(1pc) Assembly ■ MAIN FRAME ASSEMBLY 1. Remove all parts from carton. 2. Install Rear Stabilizer onto half circular of Frame Base Plate with 2pcs of 3/8”x2” Round Head Socket Screw. ■ CONSOLE SUPPORT ASSEMBLY 1.
Screw. *Please avoid cutting the wires. ■ HANDLE BAR ASSEMBLY 1. Install the Right and Left Handle Bars into Front Linkage ( R) and Front Linkage (L) with 6pcs of 5/16”x1/2” Button Head Socket Screw by using Combination M5 Allen Wrench & Screwdriver. ■ PEDAL ASSEMBLY 1. Install the Left Pedal onto plate of pedal with 4pcs of M6x25m/m Button Head Socket Screw and 4pcs of 6 x 14 x1T Flat Washers. 2. Install the Right Pedal as above. ■ PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED.
7 ZE50
Transport The elliptical is equipped with two transport wheels which are engaged when rear of ZE50 is lifted.
Power up The ZE50 is supplied with a wall mount power supply. When power is connected to the ZE50, the console will automatically power up. If there is no input to the console for 4 minutes the console will go to stand-by mode. In stand-by mode the console display will turn off. All work out data will be saved in stand-by mode. When initially powered on the large display will light. The data windows will show zero and the program choices will be blinking in the large window.
adjusted manually by pressing the Up/Down buttons. Distance and Calories will accrue, starting from zero. The Calorie window will switch between Calories and Watts every 5 seconds. The Calorie reading shows total Calories burned and is an approximate number. The Watt reading indicates how much work you are doing. If the Watt reading is 100, this means you are doing enough work to light a 100 watt light bulb. The bottom left data window will switch between RPM and Speed every 5 seconds.
count down, if desired, and press Mode. The Calorie window will now be blinking. Repeat the same process then press Mode. The Pulse window will now be blinking. Entering a Pulse number will set an alarm that will beep when your heart rate reaches the programmed number to let you know you have reached your target. Once you have set the data you may press Start to begin the program. You may also press Start at any time during the programming to begin.
exercise during the count down. At the end of the 60 seconds a score will be displayed ranging from F1 to F6 with F1 being the highest score and F6 being the lowest. FUNCTIONS TIME: Count up: accumulates training time from zero to 99:59. Count down: counts down from preset time to zero. SPEED/ RPM: Automatically toggles between SPEED and RPM every 6 seconds. Speed is in miles per hour (or kilometers per hour) DISTANCE: Count up: accumulates training distance from 0.00 to 99.99 miles.
local electric codes. 4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house wiring. 5. Expenses for making the elliptical accessible for servicing, including any item that was not part of the elliptical at the time it was shipped from the factory. 6. Damages to the elliptical finish during shipping, installation or following installation. EXCLUSIONS This warranty does not cover the following: 1.
