MSDS

MATERIAL SAFETY DATA SHEET
REVISION: 0 ISSUE DATE: 2015-4-28
SECTION 11 TOXICOLOGICAL INFORMATION
SECTION 12 ECOLOGICAL INFORMATION
SECTION 13 DISPOSAL CONSIDERATIONS
SECTION 14 Transportation
1
1.1
1.2
2
2.1
3
3.1
3.2
a
instruction 965 Section IB or II for Lithium Ion battery, the International Maritime Dangerous Goods (IMDG) Code (2010 Edition) with special provision 188 & 230, US Harzardous Materials
Rlti
The cell quantity is more than 24pcs or the battery quantity is more than 12pcs, they must be asked to meet with the requirements in blow besides they are assembled in finished
equipment.
Every package must be marked in the content that the packages are loaded in lithium cells or batteries, also add new lithium iron operation label , also need point out the corrective
actions when the packages are damaged.
Waste Dis
p
osal method O
p
ened cells should be treated as hazardous wast
e
Meet with UN Test Requirement
There is no contamination during normal operation and use. Lithium batteries should have their terminals insulated prior to disposal, do not throw away a used battery and provide them for
recycling company.
Open cells should be treated as hazardous waste. If the leakage or other material is Released, we should take actions as follows:
Leave the area, allow the batteries to cool down, let the vapors to dissipate .
Avoid skin and eye contact or inhalation of vapors. Remove spiller liquid with absorbent and incinerate after.
Lithium content requirement
49 CFR(Code of Federal Regulations)Sections 173-185 Lithium batteries and cells. the UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria 38.3 Lithium
btt i
Recycling: Send to authorized recycling facilities to get Co,Cu and Al,eventually through licensed waste carrier;
Civil Aviation Organization (ICAO) Technical Instructions (2014-2015 Edition), the International Air Transport Association (IATA) Dangerous Goods Regulations (56th Edition, 2015). Packing
For the bar cells,the lithium content can not overpass 20Wt/h;
Package Requirement
5th revised edition(UN3480) as "non-dangerous goods" or "non-hazardous materials". The mentioned batteries are complied with the special provision, Section I of PI965 to PI967. These lithium
btt i
The cell and battery must be packaged specially and singly, and put into hard outer package to prevent short-circuit if they do not be assembled in finished equipments (such as
mobile phone,camera,NBPC.and so on)
All the cell and battery must be verified to meet with all the requirements in Part 3 -38.3 item (UN38.3 tests) for "Recommendations on the Transport of Dangerous Goods, Manual
of Tests and Criteria" .
For the batteries, the lithium content can not overpass 100Wt/h;
Lishen’s 1S1P-SP381223AC-PCM Lithium Ion batteries are considered to be “rechargeable batteries” and meet the requirements of transportation by th U.S. Department of Transportation,
Incineration: incineration should never be performed by battery users but eventually by trained professionals in authorized facilities with proper gas and fumes treatment.
can be transported in nonrestrictive material and as Non-Dangerous Goods as they meet all the requirements in below:
Landfilling:According to the proper laws and regulations in different countries or areas, the battery should be buried deeply in the specified place;
This product does not elicit toxicological properties during routine handling and use.
Cobalt and its compounds can pose a threat if released to environment. The detail information are showed in waste disposal method in Section 13 "Disposal Consideration".
b
c
d
SECTION 15 REGULATORY INFORMATION
OSHA Hazard Communication Standard ( 29 CFR 1910.1200)
Hazardous Non-hazardous
SECTION 16 OTHER INFORMATION
Battery Number
Nominal Voltage 3.7
Minimum Capacity (mAh) 65
Battery Mass 4g
Equivalent Lithium Content 0.0195g
Test NO Criteria Result
38.3.4.1 Passed
38.3.4.2 Passed
38.3.4.3 Passed
38.3.4.4 Passed
38.3.4.5 Passed
38.3.4.6 ------
38.3.4.7 Passed
38.3.4.8 ------
1S1P-SP381223AC-PCM
External temperature should not exceed 170degC.No disassembly, and fire within six
hours of this test.
Every package weight can not overpass 10kg if the batteries can not be assembled in finished equipment.
There is no hazards in accordance with the UN recommendations test.(UN manual of tested and criteria 38.3)
Every package must pass 1.2mm fall test in any direction. No damage for the cells and batteries, no move and touch together, no cells or batteries escape from the package.
Every batch shipment must be appendixes document which should contain the content that the packages are loaded in lithium cells or batteries, also need point out the corrective
actions when the packages are damaged.
Forced Discharge
Shock
External temperature should not exceed 170degC.No disassembly, and fire within six
hours of this test.
No disassembly, and fire within seven days of this test.
Overcharge No disassembly, and fire within seven days of this test.
Impact
Vibration
External Short Circuit
No mass loss,leakage,venting,disassembly,rupture,and fire.OCV should not be less than
90% before testing
Test Item
No mass loss,leakage,venting,disassembly,rupture,and fire.OCV should not be less than
90% before testing
No mass loss,leakage,venting,disassembly,rupture,and fire.OCV should not be less than
90% before testing
No mass loss,leakage,venting,disassembly,rupture,and fire.OCV should not be less than
90% before testing
Altitude Test
Thermal Test
√