Assembly, Installation, & Use Instructions The information in this document is subject to change without notice. © Copyright Springfree® Trampoline Inc. 2005, 2015. All rights reserved.
WARNING Read the warnings on this page and those contained in the User Guide before you assemble and use the trampoline and enclosure. No somersaults or flips. Landing on the head or neck can cause serious injury, paralysis, or death, even when landing in the middle of the bed. No more than one person at a time. Multiple jumpers increase the chances of loss of control and collision and can result in serious head, neck, back, leg, arm or other injuries.
1 C D E 7 F 5 A B G Parts List A Quantity Parts List Quantity Backboard 1 E Bolts & Nuts 6 B Stability Rod and Brackets 1 F Short Rods 2 C Plastic Clamps 4 G Basketball and Pump 1 D Allen Key 1 H Spare Parts (cable ties, bolt and nut) 1 WARNING - Two people are recommended for assembly. NOTE - Ball colors and pattern depicted above may differ from actual.
2 WARNING - When choosing the location of the hoop on your trampoline, take into consideration ball over-throws and safe and easy retrieval. NOTE - Check that the plastic sleeves covering the net rods are intact and free from cracks or damage. If they are damaged, contact Springfree Trampoline to order replacements BEFORE installing the FlexrHoop. Remove the white c-clips located on the net rod sockets. Carefully lift the bottom end of the black net rods out of the net rod sockets and lower the net.
3 Locate the backboard and stabilising rod and brackets and place them on the lowered net. You will first need to bow the stabilising rod until it is the same width as the backboard. To do this, take hold of one of the brackets and gently push the other bracket up against a firm surface. With your free hand, pull the strap. Continue bowing the stabilising rod until width of the stability brackets is similar to the width of the backboard.
4 Starting on one side, locate a short rod and slide it into a short sleeve, with the black endcap going into the sleeve first. Insert the other end of the short rod so that it is firmly seated into the hole on the top of the stabilising bracket. Next align the following three parts: 1) the highlighted hole in the bracket, 2) the hole in the bottom of the short sleeve and 3) the hole at the end of the long support sleeve, as shown. Fasten the three parts together with a bolt and tighten with an Allen key.
5 On the rim, there are two straps with snaps at the end. Pull the ends of these straps down and under the bottom edge of the backboard and attach to the snaps on the back of the backboard as shown. Orient the bottom of the backboard so that it is on the inside of the net, and the stabilizing rod and brackets are on the outside of the net.
6 NOTE - Take care to align the plastic clamps so that they are facing the same direction. The nut will only fit one side of the plastic clamp and when fully assembled, should face the center of the trampoline with the bolt head facing outward. NOTE - As you fasten the bolts through the stabilising brackets and plastic clamps, take care not to snag the net with the Allen key. Handle the net with care and be sure that it does not get caught or it may tear.
7 In order to attach the second stabilising bracket to the “mounting rod”, you may need to loosen or tighten the strap until the bracket aligns with the plastic clamps. Align the top hole of the stabilising bracket with the top plastic clamp and fasten with a bolt. Repeat for the bottom hole and clamp. When completed, you are ready to raise the net.
8 NOTE - Before raising the net, be sure that all of the bolts are tightly fastened using the Allan key. Starting with the “mounting rods”, reinsert the black net rods into the net rod sockets on the trampoline frame and refasten the C-clips. After the net is fully raised, locate and adjust the two straps on the back of the backboard until the hoop is perpendicular to the mat. Congratulations! You have successfully completed the assembly of your Springfree FlexrHoop.
