Instructions / Assembly

IN022 Rev M 0321 43 Saber Way, Ward Hill, MA 01835 | spruce.com
2.0 Fan Sealing
RL Series fans are factory sealed, no additional caulk or other materials are required to inhibit air leakage.
3.0 Ducting
Use only metal ducting for fans used in kitchen areas or as range hood or remote blowers. Any type of ducting is acceptable
forareasotherthankitchens,however,exiblenonmetallicductingisrecommendedforeasyinstallationandquieteroperation.
Insulatedexibleductingishighlyrecommendedincoldclimatestopreventthewarmbathroomairfromformingcondensationin
theductingwhereitisexposedtocolderatticair.
ToensurequietoperationofENERGYSTARqualiedin-lineandremotefans,eachfanshallbeinstalledusingsoundattenuation
techniquesappropriatefortheinstallation.Forbathroomandgeneralventilationapplications,atleast8feetofinsulatedexible
ductshallbeinstalledbetweentheexhaustorsupplygrille(s)andthefan.Forkitchenrangehoodremoteventilationapplications,
where metal duct is generally required by code, a metal sound attenuator shall be installed between the range hood and the fan.
The outlet of the fan should always be ducted to the outside. Avoid venting the outlet of the fan directly into an attic area. The
excessmoisturefromthebathroomcancausedamagetobuildingstructureandanyitemsstoredintheattic.Multipleventing
pointsmaybeconnectedtogetherusinga"T"or"Y"tting.Straightsmoothrunsofrigidmetalductingwillpresenttheleast
resistanceandmaximizesystemperformance.TheEquivalentLengthofRigidMetalDuctingresultingin.2”WCpressureloss
foreachFanModelisprovidedinthespecicationsectionoftheseInstructions.Flexibleducting,ifused,mustalwaysbeas
closetobeingfullyextendedaspossible.Formedrigidmetalductelbowswillpresenttheleastresistanceandmaximizesystem
performance,recommendedbendradiusofelbowisatleast1.5xductdiameter.
For quietest performance, the fan should be mounted further away from the inlet duct, near the outside vent. A minimum distance
of8feetisrecommendedbetweenthefanorT/Yofamulti-intakesystemandintakegrille(s).
4.0 Back Draft Dampers
Backdraftdampersallowairowinonlyonedirectionpreventingcold/hotdraftsfromenteringthevented
areaandminimizepossiblecondensationandicingwithinthesystemwhilethefanisnotoperating.Back
draft dampers are highly recommended at each intake grille for bathroom ventilation in all cold climate
installations.
5.0 Electrical Wiring
AllwiringmustbeperformedinaccordancewiththeNationalFireProtectionAssociation’s(NFPA)”NationalElectricalCode,
Standard#70”-currenteditionforallcommercialandindustrialwork,andstateandlocalbuildingcodes.Allwiringmustbe
performedbyaqualiedandlicensedelectrician.AGroundFaultInterrupter(GFI)circuitisnotrequiredinmostinstallations,
checkyourlocalcodes.Ensurethatallexteriorelectricalboxesareoutdoorratedandproperlysealedtopreventwaterpenetration
intothebox.Ameans,suchasaweephole,isrecommendedtodrainthebox.
6.0 Applications
Suitableforgeneralventilation,bathroomventing,freshairsupply,ductboosting,buildingpressurization,etc.Suitablefor
kitchenexhaustventing.
7.0 Installation
Step 1:Attachthemountingbrackettothefanunitwith(2)#10x½”screws,provided.Avoidover
tightening screws.
Step 2:Selectlocationforfanmounting.Alocation2/3alongtheducting,aminimumof10feetaway
fromtheinletventtothefanortheY/Tofamulti-intakesystemwillprovidethequietestoperation.Fan
should be mounted vertically to prevent moisture from accumulating in the fan housing. Attach bracket to
mountingstructurewiththe11/4”screwsprovided.Ensurethefanissecurelyfastened.
Step 3:Connectductworkbetweenfaninletandareatobeventedthroughinletgrille.Flexible,nonmetallicductingis
recommendedforquietestoperationandeasiestinstallation.Insulatedexibleductingishighly recommended for bathroom
ventilation in all cold climate installations.