Operation Manual

ManualsBrandsStanley ManualsLaserTLM165 - STHT1-77139

Stanley TLM165

Table of Contents

Instrument Set-up- - - - - - - - - - - - - - - - - - - - - - -2

Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2

Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3

Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - -3

Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4

Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - -4

Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4

Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - -4

Adjusting measuring reference - - - - - - - - - - - - - - - - -4

Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - -5

Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - - 5

Measuring Functions - - - - - - - - - - - - - - - - - - -6

Measuring single distance - - - - - - - - - - - - - - - - - - - -6

Permament measuring- - - - - - - - - - - - - - - - - - - - - - -6

Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6

Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7

Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7

Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - -8

Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - -8

Memory (5 last results) - - - - - - - - - - - - - - - - - - - - - -9

Technical Data - - - - - - - - - - - - - - - - - - - - - - - - - 10

Message Codes - - - - - - - - - - - - - - - - - - - - - - - - 11

Care- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

Safety Instructions - - - - - - - - - - - - - - - - - - - - - 11

Areas of responsibility - - - - - - - - - - - - - - - - - - - - - - 11

Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12

Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - -12

Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - -12

Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12

Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12

Electromagnetic Compatibility (EMC)- - - - - - - - - - - -12

FCC statement (applicable in U.S.) - - - - - - - - - - - - -13

Laser classification- - - - - - - - - - - - - - - - - - - - - - - - -13

Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -13

Summary of content (13 pages)

PAGE 1
Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - 2 Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Switching ON/OFF - - - - - - - - - - - - - - - - -
PAGE 2
EN Instrument Set-up Introduction Overview The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them. Display The symbols used have the following meanings:  WARNING Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
PAGE 3
Instrument Set-up Display Battery Area / Volume EN Insert batteries i Pythagoras Memory To ensure a reliable use, do not use zinc-carbon batteries. Change batteries when battery symbol is flashing.
PAGE 4
EN Operations Switching ON/OFF Clear Message Codes 1x 2 sec Device is turned OFF. If the info icon appears with a number, observe the instructions in section "Message Codes". Example: Undo last action. Adjusting measuring reference 1 2 Distance is measured from the front of the device. Distance is measured from the pin of the endpiece. 3 Distance is measured from the rear of the device (standard setting).
PAGE 5
Operations Distance unit setting EN Switch between the following units: 2 sec 0.
PAGE 6
EN Measuring Functions Measuring single distance 1 2 i 3 8.532 m Aim active laser at target. Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases. Permament measuring The last value measured is displayed. 2 1 3 2 sec Stops permanent measuring. 8.532 m Aim active laser at target. Add / Subtract 1x 1 2 7.
PAGE 7
Measuring Functions Area EN 1x 1 2 3 4 Aim laser at first target point. i 5 Aim laser at second target point. 24.352 m The result is shown in the main line and the measured value above. 2 Volume 2x 1 2 3 Aim laser at first target point. i 7 78.694 m 4 5 Aim laser at second target point. 6 Aim laser at third target point. The result is shown in the main line and the measured value above.
PAGE 8
EN Measuring Functions Pythagoras (2-point) 3x 1 2 3 4 Aim laser at upper point. i 5 Aim laser rectangular at lower point. 8.294 m The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. Pythagoras (3-point) 4x 1 2 3 4 Aim laser at upper point. 8.294 m 8 Aim laser at rectangular point. i 7 5 The result is shown in the main line and the measured distance above.
PAGE 9
Measuring Functions Memory (5 last results) EN 5x 1 2 5 8.294 m 5 last results are displayed. 5 8.294 m Navigates trough 5 last results.
PAGE 10
EN Technical Data Distance measurement Typical Measuring Tolerance* ± 1.5 mm / 0.06 in *** Maximum Measuring Tolerance** ± 3.0 mm / 0.
PAGE 11
Message Codes Care Safety Instructions If the message Error does not disappear after switching on the device repeatedly, contact the dealer. If the message InFo appears with a number, press the Clear button and observe the following instructions: • Clean the device with a damp, soft cloth. • Never immerse the device in water. • Never use aggressive cleaning agents or solvents. The person responsible for the instrument must ensure that all users understand these directions and adhere to them. No.
PAGE 12
EN Safety Instructions Permitted use Hazards in use Disposal • Measuring distances • Tilt measurement  WARNING  CAUTION Prohibited use • • • • • • • • • Watch out for erroneous measurements if the instrument is defective or if it has been Using the product without instruction dropped or has been misused or modified. Using outside the stated limits Carry out periodic test measurements.
PAGE 13
Safety Instructions FCC statement (applicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.