SDS

STAR*TRON GASOLINE ADDITIVE MSDS
PAGE 8 OF 10
15. REGULATORY INFORMATION (Continued)
EUROPEAN UNION INFORMATION FOR PRODUCT:
EU LABELING AND CLASSIFICATION (continued):
EUROPEAN UNION ANNEX II HAZARD SYMBOL:
EUROPEAN UNION INFORMATION FOR CONSTITUENTS: The following information is available for primary constituents in
the components of this product.
Solvent Naphtha (Petroleum), Heavy Aliphatic:
EU EINECS/ELINCS NUMBER: 265-200-4
EU CLASSIFICATION: Harmful. [Xn]
EU RISK PHRASES: [R: 65]: Harmful; may cause lung damage if swallowed.
EU SAFETY PHRASES: [S: 2-]: Keep out of the reach of children. (This safety phrase can be omitted from the label when the
substance or preparation is sold for industrial use only). [S: 23]: Do not breathe fumes, vapors or spray. [S: 62]: If swallowed,
do not induce vomiting. Seek medical advice immediately and show this container or label.
16. OTHER INFORMATION
PREPARED BY: CHEMICAL SAFETY ASSOCIATES, Inc.
Po Box 36519, La Mesa, CA 91944-3519
[phone]
DATE OF PRINTING: October 3, 2012
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of
these data or the results to be obtained from the use thereof. Star brite assumes no responsibility for injury to the vendee or third persons
proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Additionally, Star brite
assumes no responsibility for injury to vendee or third persons proximately caused by abnormal use of the material even if reasonable safety
procedures are followed. Furthermore, vendee assumes the risk in his use of the material.
DEFINITIONS OF TERMS
A large number of abbreviations and acronyms appear on an MSDS. Some of these, which are commonly used, include the following:
CAS #: This is the Chemical Abstract Service Number that uniquely
identifies each constituent.
EXPOSURE LIMITS IN AIR:
CEILING LEVEL: The concentration that shall not be exceeded during
any part of the working exposure.
LOQ: Limit of Quantitation.
MAK: Federal Republic of Germany Maximum Concentration Values in
the workplace.
NE: Not Established. When no exposure guidelines are established, an
entry of NE is made for reference.
NIC: Notice of Intended Change.
NIOSH CEILING: The exposure that shall not be exceeded during any
part of the workday. If instantaneous monitoring is not feasible, the
ceiling shall be assumed as a 15-minute TWA exposure (unless
otherwise specified) that shall not be exceeded at any time during a
workday.
NIOSH RELs: NIOSH’s Recommended Exposure Limits.
PEL-Permissible Exposure Limit: OSHA’s Permissible Exposure
Limits. This exposure value means exactly the same as a TLV, except
that it is enforceable by OSHA. The OSHA Permissible Exposure Limits
are based in the 1989 PELs and the June, 1993 Air Contaminants Rule
(Federal Register: 58: 35338-35351 and 58: 40191). Both the current
PELs and the vacated PELs are indicated. The phrase, “Vacated 1989
PEL,” is placed next to the PEL that was vacated by Court Order.
SKIN: Used when a there is a danger of cutaneous absorption.
STEL-Short Term Exposure Limit: Short Term Exposure Limit, usually
a 15-minute time-weighted average (TWA) exposure that should not be
exceeded at any time during a workday, even if the 8-hr TWA is within
the TLV-TWA, PEL-TWA or REL-TWA.
TLV-Threshold Limit Value: An airborne concentration of a substance
that represents conditions under which it is generally believed that nearly
all workers may be repeatedly exposed without adverse effect. The
duration must be considered, including the 8-hour.
EXPOSURE LIMITS IN AIR (continued):
TWA-Time Weighted Average: Time Weighted Average exposure
concentration for a conventional 8-hr (TLV, PEL) or up to a 10-hr (REL)
workday and a 40-hr workweek.
IDLH-Immediately Dangerous to Life and Health: This level represents
a concentration from which one can escape within 30-minutes without
suffering escape-preventing or permanent injury.
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HAZARD
RATINGS: This rating system was developed by the National Paint and
Coating Association and has been adopted by industry to identify the
degree of chemical hazards.
HEALTH HAZARD:
0 (Minimal Hazard: No significant health risk, irritation of skin or eyes not
anticipated. Skin Irritation: Essentially non-irritating. PII or Draize = “0”.
Eye Irritation: Essentially non-irritating, or minimal effects which clear in <
24 hours [e.g. mechanical irritation]. Draize = “0”. Oral Toxicity LD
50
Rat: <
5000 mg/kg. Dermal Toxicity LD
50
Rat or Rabbit: < 2000 mg/kg. Inhalation
Toxicity 4-hrs LC
50
Rat: < 20 mg/L.); 1 (Slight Hazard: Minor reversible
Injury may occur; slightly or mildly irritating. Skin Irritation: Slightly or mildly
irritating. Eye Irritation: Slightly or mildly irritating. Oral Toxicity LD
50
Rat: >
500-5000 mg/kg. Dermal Toxicity LD
50
Rat or Rabbit: > 1000-2000 mg/kg.
Inhalation Toxicity LC
50
4-hrs Rat: > 2-20 mg/L); 2 (Moderate Hazard:
Temporary or transitory injury may occur. Skin Irritation: Moderately
irritating; primary irritant; sensitizer. PII or Draize > 0, < 5. Eye Irritation:
Moderately to severely irritating and/or corrosive; reversible corneal opacity;
corneal involvement or irritation clearing in 8-21 days. Draize > 0, < 25.
Oral Toxicity LD
50
Rat: > 50-500 mg/kg. Dermal Toxicity LD
50
Rat or Rabbit:
> 200-1000 mg/kg. Inhalation Toxicity LC
50
4-hrs Rat: > 0.5-2 mg/L.);