Manual

ManualsBrandsStar Headlight & Lantern ManualsLightingULB9S Star Mini-Phantom Undercover

PLITSTR46 REV. K 1/6/15

This light is designed to be mounted on the inside of your vehicle.

It is not intended for exterior applications and is not warranted

against water damage.

It is the sole responsibility of the owner to ensure the warning light is

secure. Check your light every time you enter the vehicle to ensure that

it is mounted securely. The manufacturer assumes no responsibility for

the secure mounting of this light.

IMPORTANT: Please read all of the following instructions before installing your new light.

CAUTION: Please be sure to check that your cigarette plug outlet or hard wire is properly

fused with a 5 amp fuse. Testing the light before this fuse is properly

installed will void the warranty on the light.

Star Mini Phantom

™

Interior Undercover Mini LED Light

PATENTS D530,029 and D632,421

ULB9 Series

(Discrete LEDs)

ULB9S Series

(Starburst LEDs)

Summary of content (8 pages)

PAGE 1
Star Mini Phantom™ Interior Undercover Mini LED Light PATENTS D530,029 and D632,421 ULB9 Series (Discrete LEDs) ULB9S Series (Starburst LEDs) IMPORTANT: Please read all of the following instructions before installing your new light. CAUTION: Please be sure to check that your cigarette plug outlet or hard wire is properly fused with a 5 amp fuse. Testing the light before this fuse is properly installed will void the warranty on the light.
PAGE 2
Parts ULB9-**: 1 1 Standard Mini Phantom Head with Cig Plug 274-ULB9BKT Mounting Kit ULB9S-**: 1 1 1 1 2 Starburst Mini Phantom Head with Cig Plug ULB9-HOOD-1 Flashback Hood with Windshield Brackets S111-6 Hood Gasket PLABULB9 Reflective Hood Label P30019-267 Pivoting Flush Mount Brackets ULB9-1-**: 1 1 Standard Mini Phantom Head with Hardwire 274-ULB9BKT Mounting Kit ULB9S-1-**: 1 1 1 1 2 Starburst Mini Phantom Head with Hardwire ULB9-HOOD-1 Flashback Hood with Windshield Brackets S111-6 Hood Ga
PAGE 3
ULB9S Mounting Front Windshield Adhesive Mount ! 1. The hood can be installed such that the cord can exit either side. Route the cord through the appropriate slot and slide the hood onto the back of the light until the hooks on the hood “latch” onto the light. 2. If desired, install the rubber gasket along the edge of the hood to help reduce vibration against the window, as well as to allow for minor adjustments to the curvature of the window. 3.
PAGE 4
(ULB9S Mounting CONT’D) Optional Reflective Hood Label Installation Practice installing label BEFORE removing backing. 1. Align the notch in the label with the center of the hood taking care that the front edge of the label lines up with the front edge of the hood. 2. Hold one half of the label firmly in place with the backing still affixed. ULB9S Optional 3. Slowly start to peel the backing off of the other half of the label from the center out. 4.
PAGE 5
(Bracket Mounting CONT’D) ULB9 Bracket Mounting (Deck, Mirror, or Suction Cup) 1. Decide which side you want the cord to exit the light and determine which way you will need to mount the ULB9-BKT to your light. 2. Attach Part A of the mounting bracket, facing the direction you have selected, to the light by using two of the Philips head screws. CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes and result in a faulty mount. 3.
PAGE 6
ULB9 and ULB9S Connections and Operation ULB9/9S (cig plug version only) The ULB9 (cig plug version) can be left plugged into the cig plug outlet in your vehicle. It can be turned on and off using the lighted power switch on the cord. The pattern select switch is used to preset the desired pattern. You can cycle through the different patterns by briefly pressing the pattern select switch and releasing it. The ULB9 has 35 patterns to choose from.
PAGE 7
ULB9-1 and ULB9S-1 Wiring and Operation (hardwired version only) The ULB9-1 (hard wire) should be wired through a 5 amp fuse (not supplied) and a 12VDC switch (not supplied) capable of handling at least 5 amps. Connect the wires as follows: Black - Good Chassis Ground Red - Power (+12 VDC) White - Synchro: AFTER PROGRAMMING, Connect the white wires from the two lights together to synchronize them together. Green - Pattern Select: Touch and release to Ground to scroll through the patterns.
PAGE 8
LED FIVE YEAR LIMITED WARRANTY The manufacturer warrants this LED light against factory defects in material and workmanship for five years after the date of purchase. The owner will be responsible for returning to the Service Center any defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its option, products, or part(s), which its inspection determines to be defective.