Replacement Part List

3
Air-cooled Single cylinder Engine is amounted as power
source and Centrifugal Clutch is fixed on engine output
shaft．Petrol Engine(2 cycle，4 cycle)and Diesel Gasoline
Engine can be mounted as option．Centrifugal Clutch
engages by running up the engine and engine R.P.M. is
reduced to suitable number for compacting．The rotation
of engine is transmitted from V—pulley integrated with
Clutch drum to Vibrator pulley through V-belt．
Vibrator Pulley rotates Eccentric rotor shaft that is contained
in Vibrator case．The generated vibration created
from eccentric rotor is transmitted to Compaction with the
weight of the machine makes the compaction of the
ground possible．
FUNCTIONS AND CONTROLS
Motor
The motor is controlled by an ON/OFF switch or push button
which is mounted on the motor below the fuel tank．
The motor speed is controlled by a remote throttle lever which
is mounted on the machine handle．
The motor is fitted with an oil alert device which will st．o．p the
motor or prevent starting when the crankcase Oil level fulls
below a safe level．
Drive belt
Tension of the drive belt is adjustable．Loosen the four nuts on
the bolts which secure the motor to the base plate,Adjust the
set screws which bear against the motor crankcase to
achieve the required belt tension．Ensure that the four nuts
and the set screw lock nuts are tightened after adjustment．
ACCESSORIES
Transport Trolley-facilitates handling．Hooks into the base-
plate．Fitted with 200mm rubber tyres.
FOR SAFETY OPERATION
!This safety alert symbol identifies
important safety messages throughout
this manual and on the machine．
When you see this symbol,carefully read
the message that follows．Your safety is
at stake !
Foreword：
It is important to read this manual carefully so
that you will fully understand the operational
characteristics and performance of the plate
compactor．Proper maintenance procedures Will
insure long life and top performance of the unit.
Safety：
This section outlines basic safety procedures that
apply to the operation，maintenance and
adjustment of the plate compactor．This
unit is designed as a powerful,productive
machine that should be operated with respect and
caution． ．．
Misuse or carelessness can result in serious injury
or property damage,or both．Safety precautions
must be observed at all times．
Operator Qualifications：
Before operating this equipment，an individual
should read this manual．Whenever possible,he
should be shown how to operate the unit by an
experienced operator．Inexperience is hazardous
in operating any machine or attachment．Trial and
error is not the way to become familiar with a
piece of equipment．This is expensive,cuts
equipment life and can create machine downtime．
Inexperience can cause injury or death．The
machine should not be Ieft unattended when
operating．
General Safety：
!CAUTION
Protection required．Wear hard hat．shatterproof
glasses,steel toed boots and other protective
devices required by job conditions．Avoid jewelry
or loose clothing．These many catch on controls
or in moving parts and cause serious injury.
Starting Safety:
!CAUTION
Poisonous fumes．Start and operate only in well
ventilated area．Breathing exhaust gases can
result in sickness or death．
Servicing Safety：
!CAUTION
Flammable liquid．Stop engine and do not
smoke or allow work in immediate area
when refueling．Fire or explosion could
result from flames or sparks．
Moving parts．Shutdown engine before
performing． Service or maintenance.
Contact with moving parts can cause
serious injury．
Fligh temperature．Allow machine and
engine to COOl before performing service
or maintenance． Contact with hot
components can cause serious burns.
Engine
See engine operations manual
SHUTDOWN
EMERGENCY SHUTDOWN
Move throttle lever to "OFF" position
and also turn stop switch to "OFF"．
NORMAL SHUTDOWN
Move throttle lever quickly from
"ON" to "OFF" and run engine for 3
to 5 minutes at low speed．After
engine cools, turn stop switch to
"OFF" position．Close fuel shutoff
valve．