Operations Manual

50 | Regulatory
Information
Regulatory
Information
|
51
The Synergy Charger has been tested to, and has passed, the following
emissions
and
immunity
tests:
IEC
60601-1-2
radiated and conducted
emissions requirements
for a Group 1
Class B device as stated in CISPR 11
.
Harmonic distortion
and voltage
fluctuations
affecting the power
input
source
as stated in Table 2 of IEC
60601-1-2
.
RF radiated
immunity
at a field level of 10
V/m
between 80
MHz
and 2
.
7 GHz
as well as higher field levels
from communications
devices as stated in Table 9
of IEC
60601-1-2
.
Immunity
to power frequency magnetic fields at a field level of 30
A/m
.
Immunity
to ESD levels of
+/-
8 kV conducted discharge and
+/-
15 kV air
dischar
ge
.
Immunity
to Electrical fast
transients
on the power
input
at a level of
+/-
2 kV
at a 100 Hz repetition
rate
.
Immunity
to Surges on the power
input
of
+/-
1 kV line to
line
.
Immunity
to conducted disturbances induced by RF fields on the power input
as stated in Table 6 of IEC
60601-1-2
.
Immunity
to voltage dips and
interruptions
on the power
input
as stated in
Table 6 of IEC
60601-1-2
.
Starkey Hearing
Technologies
6700
Washington
Ave
.
South
Eden Prairie, MN 55344 USA
Wm
.
F.
Austin House,
Bramhall
Technology Park
Pepper Road, Hazel Grove,
Stockport
SK7 5BX
United Kingdom
Class II Device
Waste
from
electronic equipment
must
be handled according to
local regulations
Consult Operations Manual
INSTRUCTIONS
FOR
DISPOSAL
OF OLD ELECTRONICS
Starkey Hearing Technologies encourages, the EU requires, and
your
local
community
laws may require, that your hearing aids and charger be
disposed of via your local electronics
recycling/disposal pr
ocess.
The
instructions
below are provided for the benefit of disposal/recycling
personnel
.
Please include this
manual
when disposing of your hearing aids
and/or char
ger
.
WIRELESS
NOTICES
FCC ID: EOA-24LIVIORCHG
IC: 6903A-24LIVIORCHG (Livio RIC R, Via RIC R, AGXsliv RIC R, Esentia RIC R,
Livio AI RIC R, Via AI RIC R, AGXsliv AI RIC R, Esentia AI RIC R, Livio RIC
Rechargeable, Via RIC Rechargeable, AGXsliv RIC Rechargeable, Esentia RIC
Rechargeable, Livio AI RIC Rechargeable, Via AI RIC Rechargeable, AGXsliv AI
RIC Rechargeable, Esentia AI RIC Rechargeable)
FCC
NOTICE
This hearing aid and Synergy Charger comply with part 15 of the FCC rules and
with
ISED
Canada license-exempt RSS
standar
ds. Operation is subject to the
following two c
on
d
itions
:
(1)
This device
may
not cause
harmful
interference, and
(2)
this device
must
accept any interference received,
including
interference that may
cause undesired
operation
of the de
vi
ce
.
Note: The
manufacturer
is not responsible
for
any radio or TV interference caused by
unauthorized modifications
to this
equipment
.
Such
modifications
could void the users
authority
to operate the
equipment.
Cet appareil est conforme à la partie 15 des règles de la FCC et avec les normes RSS
de licence d’ISDE Canada. Le fonctionnement est soumis à deux conditions: (1) Cet
appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter
toute interference reçue, y compris les interférences qui peuvent causer des
fonctionnements du dispositif.
NOTE: Le manufacturier n’est pas responsable de l’interférence créée par la
modification de cet équipement lors de l’écoute du téléviseur ou de la radio. De
telles modifications pourraient entrainer larévocation de l’autorité de l’utilisateur à
opérer cet équipement.
EU NOTICE
Hereby,
Starkey
Hearing Technologies declares that the RIC is in compliance with the
essential
requirements
and other relevant
provisions
of Directive 2014/53/EU
.
A copy of
the Declaration of
Conformity
can be obtained
from
the address below or
from
docs.
.
starkeyhearingtechnologies
.
com
FOR
DISPOSAL/RECYCLING PERSONNEL
ONLY
These products contain
Lithium
Ion Polymer
batteries.
For instructions
on removing the battery
from
the hearing aids, please visit
docs
.
starkeyhearingtechnologies
.
com
.
To remove the battery
from
the
Synergy Charger:
Remove the
four
skid pads on the
bottom
of the charger base to
access
fasteners.
Remove
fasteners
using a
Phillips
head
screwdriver
.
Disassemble the charger base
from
the bezel to expose the battery cell
.
Cut the THREE battery wire leads ONE AT A TIME close to the battery cell
to avoid
shorting
.
Pry battery
from
base using a wide flat blade
making
sure not to puncture
the battery cell
.