Desk Stand for Dual Monitors ARMBARDUO *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.startech.com/ARMBARDUO.
Table of Contents Introduction.............................................................................................1 Packaging content..................................................................................................................................... 1 Product diagram.....................................................................................2 Rear view..........................................................................................................................
Introduction Use the ARMBARDUO to mount two LCD or LED monitors up to 24 inches in size on a single base and save space. The included cable-management clips make it easy to route your cables and help to keep your area clear of cables.
Product diagram Rear view Crossbar VESA monitor mount Monitor (not included) Cable-management clip (crossbar) Height-adjustment ring Pole Baseplate Instruction manual Cable-management clip (pole) 2
Assembly Warning! Make sure that all of the hardware is assembled securely and checked for stability before you load the monitors. Assemble the base 1. Insert the three M6x15 mm screws (3) through the three holes in the baseplate (2) and into the pole (1) (figure 1). 2. Use the M4 Allen key (13) and turn the screws clockwise to tighten them.
Attach the crossbar 1. Slide the height-adjustment ring (6) down the pole (1) to the height that you want the monitors to be at. 2. Press the lever on the height-adjustment ring to tighten it and prevent it from sliding down the pole. 3. Slide the crossbar (7) down the pole so that it sits on the height-adjustment ring. 4. Push the pole cap (5) down onto the top of the pole (figure 2). figure 2 Pole cap Height-adjustment ring Crossbar Pole 5.
Attach the monitors Warning! The ARMBARDUO is designed to display two monitors between 15 and 24 inches in size. The maximum weight capacity of the ARMBARDUO is a total of 35.2 lb. (16 kg), with each monitor mount able to hold 17.6 lb. (8 kg). To prevent scratching during the installation process, you should handle the surface of the monitors with care. 1. To loosen the plates on the crossbar (7), turn the thumbscrews at the bottom of the plates counterclockwise (figure 4).
figure 6 Thumbscrew Thumbscrew 5. Do one of the following: • To install monitors that have a flush installation surface, insert four of the M4x12 mm screws (9) through the VESA monitor mount (8) and into the mounting holes on the back of the monitor. Use a Phillips screwdriver to tighten the screws (figure 7).
Adjusting the Monitors Tilt Adjustment The Monitors can be tilted to commodate different viewing angels (15 degrees downward or upward). • Place both of your hands on either side of the Monitor and apply light pressure either downward or upward. The Monitor will tilt to a maximum of 15 degrees in either direction. (figure 9). figure 9 Swivel Adjustment The Monitors can be adjusted on a 360 degree swivel. • Place both of your hands on either side of the Monitor and apply light pressure either left or right.
Route the cables The ARMBARDUO comes with cable-management clips that you can use to direct the monitor cables along the crossbar and down the pole so that they are out of your way. Make sure that the cables that you’re routing are unplugged before you complete the following steps. 1. Attach the two cable-management clips (crossbar) (14) from the crossbar (7) (figure 10). If necessary, you can move the cable-management clips right or left along the crossbar. figure 10 Cable-management clips 2.
3. Hold the cables against the pole and snap the cable-management clip (pole) (4) over the ca bles and onto the pole. You can place the cable management clip on the front or the back of the pole, depending on your preference.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.