Wireless N USB 2.0 Network Print Server *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Product Diagram.......................................................................
Introduction Packaging Contents • 1x Wireless USB Print Server • 1x Power Adapter • 1x Software CD • 1x Quick Start Guide System Requirements • Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64), Windows Server® 2012, 2008 R2, 2003 (32/64), Mac OS 10.x, 9.x, Linux 2.4.x / 2.6.x / 3.x (Tested up to 3.
Product Diagram Front View WLAN LED WPS Button Reset Button Rear View LED Indicators Ethernet Port DC Jack Instruction Manual USB Port 2
LED Indicators LED State Indication Status Blinking for POST (Yellow) When power is connected, the Status indicator will flash five times, and then go solid. USB On (Green) LAN Port has a valid network connection at 100Mbps. WLAN On (Yellow) LAN Port has a valid network connection at 10Mbps. Reset Button Reboot the Print Server: 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it.
Default Settings Username: admin Password: (None) Wireless Mode: Ad-Hoc (Peer-to-Peer) SSID: PM1115UW IP Address: 192.168.0.10 Installation Hardware Installation 1. Turn off the power to your printer. 2. Connect the print server to your printer with the appropriate printer cable. 3. Turn the printer on. 4. Plug in the AC power adapter into the DC jack on the print server. 5. Wait ~40 seconds for the print server’s Power On Self Test (POST) to complete. 6.
PM1115UW Note: If you cannot find the PM1115UW network, then your version of Windows may not be configured to show Ad-Hoc wireless networks. To resolve this issue, you need to use an RJ45 cable to either connect your print server to your network switch or to connect directly to the computer. When the setup is complete, you can disconnect the network cable. 2. Insert the setup CD into your CD/DVD drive. 3. Select “Run autorun.exe” from the Autoplay menu.
Note: The setup CD will install the print server driver, PSAdmin and Setup Wizard into your computer. The default installation directory will be C:\Program files\ Network Print Monitor. 4. Click Next on the following screen and the wizard will automatically discover the print server. At this point of the install, you may Windows Firewall message, click Allow Access if prompted.
5. From the “Select A Print Sever” screen, select the print server that you want to configure and click Next.
6.
Select your desired Communication Type: • Infrastructure (Access Point) • Ad-Hoc (Peer-to-Peer; default) SSID: • If using Ad-Hoc mode, enter the SSID you would like the print server to display • If using Infrastructure mode, enter the SSID of the access point that you want to connect to Note: If you require a site survey to determine the names of available access points, please use the web console method, outlined in the full online manual.
• Channel: optional • Data Transmit Rates: select Auto or others • Transmit Mode: select Auto or others • On the Wireless Security screen, enable or disable WEP/WPA/WPA2 encryption, configure according to your wireless network and click Next. • On the TCP/IP Settings screen, specify a fixed or dynamic IP address for the print server, a fixed IP address is highly recommended. Click Next. Note: The IP address of print server must be within the same subnet as your network adapter. 7.
9. Make sure the Use the following port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down list. Then click Next.
10. Select Manufacturer and Printer from the lists of printer drivers. Then click Next. 11. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Then click Next. 12. Then, choose whether you want to share the printer with other network user, print a test page (please select No.), etc.
14. Click Start -> Printers and Faxes and highlight your newly installed printer.
15. Right-click, select Properties, then the Ports tab and verify that the print server’s port appears.
16. Select the General tab and click Print Test Page to verify the configuration. Note: If you want to install more print servers, start the setup wizard from your Windows Start menu: Start -> All Programs -> Network Print Server -> PSWizard and repeat the installation procedure.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.