User's Manual

ManualsBrandsSTEELMATE ManualsElectronicsSINGLE-WAY TRANSMITTER

RS1-G3

ONE BUTTON REMOTE START SYSTEM

OPERATING INSTRUCTIONS

CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP

Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating

your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote

Start connections, Flashing lights, and Brake Reset. For programming, the program button must be installed.

-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing

dealer i.e. Door Locks, Horn-Honk, Anti-Grind, etc. These features may also require additional parts and/or labor

fees. Consult with your installer beforehand to be sure of what is going to be installed with your particular system.

CRIMESTOPPER SECURITY PRODUCTS, INC.

1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV 08.15.2011

This device complies with FCC Rules part 15. Operation is

subject to the following two conditions: 1) This device may not

cause interference, and (2) this device must accept any

interference that may be received, including interference that

may cause undesired operation. The manufacturer is not

responsible for any changes or modifications not expressly

approved by manufacturer for compliance. Such modification

could void the user's authority to operate the equipment.

Summary of content (15 pages)

PAGE 1
RS1-G3 ONE BUTTON REMOTE START SYSTEM OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
PAGE 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………….….…………2 Using the Remote Transmitter………………………………………………………………………….………....…….3 Status LED……………………………………………………………………………………………….……….……….4 Remote Engine Control…………….…..……………………………………………………………….…….……….4-7 Turbo Timer Mode……………………………….……………………………………...……………….……………..…8 Manual Transmission Mode……………………………….……………………………………...…………………..…9 Convenience and Safety Features……………………………….………………………………….…...………..10-11 Transmitter Programming….
PAGE 3
USING THE REMOTE TRANSMITTER REMOTE START BUTTON PRESS SELECTION (Option # 6): The transmitter supplied with this system is a single button remote control. To eliminate the possibility of accidentally starting the vehicle, there are (3) options for button press selection. This option will allow you to change whether the Remote Starter is activated by a: 1. Double Button - ½ second presses. 2. *Single ½ second press (Default). 3. Press and Hold 2 seconds.
PAGE 4
STATUS LED VEHICLE STATUS LED : Used for Remote Start Diagnostics – page 13 (Install optional) The optional LED will remain solid when the system is in Valet Service mode. The remote start function WILL NOT operate when in Valet Mode. See page # 10 for Valet Mode. REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (*default). Parking lights flash once, return solid, and the Ignition/Acc circuits turn on.
PAGE 5
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to 4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to help prevent damage to the starter from over cranking.
PAGE 6
REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle will remain running for the programmed time or until canceled. The Run Time choices are: 10, 20, 30 minutes or Infinity Run. Default = 20 minutes Examples: • You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle, (with keys in hand).
PAGE 7
REMOTE ENGINE CONTROL SELECTABLE HOURLY COLD-START MODE (1-4 HOURS) This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. TIMED SELF-START MODE – Exiting the Vehicle: 1) Engine should be running with the Key. Press the Remote Start button for at least 1 second. Lights will turn on signaling the remote start has turned on and doors will unlock.
PAGE 8
TURBO TIMER MODE (OPTION #22) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. The Default = OFF. To Activate Turbo Timer: With the engine running by key, press Remote Start Button with brake pedal depressed.
PAGE 9
MANUAL TRANSMISSION MODE (Option 11) MANUAL TRANSMISSION EXIT PROCEDURE (Option #11-1 and 11-3) This system features a Manual Transmission Mode. When exiting the vehicle, there is a safety check out procedure required for the manual transmission mode to work. There are 2 choices of operation: 1. Option 11-1: With engine running and vehicle in neutral, set parking brake, then press “Idle Down” Icon or remote start on transmitter. The remote starter will turn on and take over operation of the vehicle. 2.
PAGE 10
CONVENIENCE AND SAFETY FEATURES AUTO LOCK / UNLOCK (Option # 2) The Auto Lock feature controls whether the doors will automatically lock/unlock on your vehicle when driving or with turning the Ignition ON/OFF. If the Auto Lock feature is turned on, and your system is in “Tach” mode, then the doors should automatically lock as the engine RPM’s increase (driving).
PAGE 11
CONVENIENCE AND SAFETY FEATURES HOOD OPEN SAFETY (Requires hood pin switch) Prevents the engine from being Remote Started when hood is open. Eliminates risk of injury to someone working under the hood of the vehicle with a properly working hood pin installed. If Remote Start button is pressed with the hood open, the lights will flash twice and the unit will not attempt a start. The system will abort Remote Start any time the hood is opened. See Remote Start Diagnostics on page 13.
PAGE 12
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS-1G3 learns up to 4 different transmitter codes. 1. Turn Ignition Key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press the start button of the first transmitter.
PAGE 13
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. This leaves the doors unlocked while Remote Started. To resolve this problem, have your installer connect the door locks to the Remote Start Keyless Entry.
PAGE 14
BATTERY REPLACEMENT To replace the battery: Simply remove the screw on back of the transmitter and slide the case apart as shown. Remove the two CR-1620 Lithium batteries and replace. Put case back together and tighten screw.
PAGE 15
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry. Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module.