Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
13
English
6 Charger Safety
■ To reduce the risk of electric shock or fire from a short
circuit:
– Make sure the blower and charger are completely
dry before starting the charging process.
■ The charger heats up during the charging process. To
reduce the risk of fire:
– Do not operate on a combustible surface (e.g.,
paper, cardboard, textiles) or in a combustible
environment.
– Allow the charger to cool down normally. Do not
cover it.
■ Chargers can produce sparks which may ignite
combustible gases, liquids, vapors, dusts or other
combustible materials. To reduce the risk of fire and
explosion:
– Do not operate in a location where combustible
gases, liquids, vapors, dusts or other combustible
materials are present.
■ Using a damaged power supply cord or plug may result in
fire, electric shock and other personal injury or property
damage. To reduce these risks:
– Replace the charger if the power supply cord
becomes damaged. The power supply cord cannot
be repaired or replaced.
– Unplug the charger from the wall outlet when not in
use.
– Never jerk the power supply cord to disconnect it
from the wall outlet. To unplug, grasp the plug, not
the power supply cord.
– Do not use the power supply cord for any other
purpose, e.g., for carrying or hanging up the charger.
– Make sure the power supply cord is located or
marked so that it will not be stepped on, tripped over,
come in contact with sharp objects or moving parts,
or otherwise be subjected to damage or stress.
■ An extension cord should not be used unless absolutely
necessary. Overloading an extension cord can result in
overheating and fire. If an extension cord must be used:
– Use only a properly wired 16 gauge (AWG16) or
heavier gauge extension cord.
– Never connect more than one charger or other
device to an extension cord.
– Never use an extension cord with a wattage rating
lower than the wattage on your charger's rating
plate.
– Never use an extension cord if the blades on its plug
are different from the blades on the charger plug in
number, size or shape.
– Do not link (chain) extension cords.
■ In case of fire, or if the charger or blower it is charging
emits smoke, an unusual smell, feels hot or appears
abnormal in any other way:
– Immediately disconnect the charger from the outlet.
Contact the authorities in the event of fire or
explosion.
– Have the charger and blower inspected and repaired
by an authorized STIHL servicing dealer before use.
■ Operation of the blower is disabled during the charging
process to reduce the risk of electric shock.
– Do not attempt to operate the blower during the
charging process or any time it is connected to the
LK45.
– Check the charger's power supply cord
and plug regularly for damage. If
damaged, immediately disconnect the
plug from the wall outlet.