Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
16
English
11 LED Diagnostics
WARNING
Since the blower and charger heat up during the charging
process, do not charge the blower on a combustible surface
or in a location where combustible gases, liquids, vapors,
dusts or other combustible materials or substances are
present, @ 6.
To charge the blower:
► Remove the activation key, @ 13.2.
► Insert the charger plug into a properly installed wall
outlet(1) with the same voltage and electrical frequency
stated on the charger's rating plate(2).
► Push the connector(4) into the blower's charging
socket(5) until it stops.
The LEDs on the blower(6) glow green during charging
and show the state of charge.
When the LEDs on the blower go out, the charging
process is complete and the charger will shut itself off.
► Remove the charger from the blower and disconnect the
charger plug from the wall outlet when charging is
complete.
A blower is not fully charged when it ships from the factory.
STIHL recommends that you fully charge the blower before
using it the first time.
Operate the charger only indoors, in dry rooms and within an
ambient temperature range of 32°F to 104°F (0°C to
40°C).
The blower heats up during operation. The charging process
begins only after the blower and its integrated battery have
cooled down sufficiently.
Charging time depends on a number of factors, including the
condition of the integrated battery and the ambient
temperature. For a complete list of approximate charging
times, see www.stihl.com/charging-times.
Operation of the blower is disabled during charging and any
time the blower is connected to the charger.
11.1 Blower Status
LEDs on the blower show the status of the power tool and its
integrated battery.
If three LEDs glow red continuously: the integrated battery
is either too hot or too cold. Allow the blower to warm up or
cool down gradually at an ambient temperature of about
50°F to 68°F (10°C to 20°C).
If three LEDs flash red when you activate the trigger switch:
the blower has an electrical malfunction. Do not operate or
charge the blower. Have it checked by an authorized STIHL
servicing dealer before use or storage.
For troubleshooting information, @ 22.
11.2 Charge Status
The LEDs also show the blower's state of charge.
4
0000-GXX-2267-A0
6
5
3
2
1
11 LED Diagnostics