Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
17
English
12 Assembling the Blower
To determine the blower's state of charge:
► Press the push button(1) on the blower.
The LEDs on the blower will glow or flash green for about
5seconds and indicate the state of charge (see
illustration).
For example:
If four green LEDs glow continuously: full charge.
If one green LED is flashing: less than 20% charge.
12.1 Mounting the Blower Tube and Nozzle
WARNING
Make sure the activation key is removed before starting
assembly. Never operate your blower without a properly
mounted blower tube and nozzle, @ 5.7.4. Use only
attachments supplied or expressly approved by STIHL,
@ 5.5.
To mount the blower tube and nozzle:
► Align the holes on the nozzle(2) with the lugs on the
blower tube(3).
► Push the nozzle(1) onto the blower tube(4).
The nozzle will engage with an audible click. Once the
nozzle and blower tube are assembled, keep them
connected during use and storage.
► Align the blower tube mounting lugs(6) with the grooves
on the blower tube(5) and push the parts together.
► Rotate the blower tube toward the symbol until it stops.
The blower tube should lock in position.
13.1 Inserting the Activation Key
WARNING
To reduce the risk of severe personal injury from unintended
activation, never store the activation key in the blower.
12 Assembling the Blower
0000-GXX-2268-A0
20-40%
40-60%
60-80%
80-100%
0-20%
1
13 Inserting and Removing the Activation
Key
2
3
0000-GXX-2594-A0
1
4
5
6