Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
18
English
14 Switching the Blower On and Off
To insert the activation key:
► Place the blower on a level surface.
► Insert the activation key (1) into the activation key
socket(2) with even, steady pressure until it stops.
Inserting the activation key enables the flow of electrical
power from the integrated battery to the motor.
13.2 Removing the Activation Key
WARNING
To reduce the risk of severe personal injury from unintended
activation, always remove the activation key before
assembling, transporting, adjusting, cleaning, servicing,
maintaining or storing the blower and any other time it is not
in use.
To remove the activation key:
► Release the trigger switch.
► Place the blower on a level surface.
► Remove the activation key with even, steady pressure.
► Store the activation key away from the blower in a safe
place that is inaccessible to children and other
unauthorized users.
14.1 Switching On
WARNING
Never operate your blower if it is modified, damaged,
improperly adjusted or maintained, not completely and
securely assembled or not functioning properly, @ 5.5. To
reduce the risk of personal injury, always wear proper
clothing and protective apparel, including proper eye
protection, when operating your blower, @ 5.4.
Before switching on:
► Make sure you have a secure and firm footing.
► Stand upright.
► Always hold and operate the blower with one hand firmly
on the control handle.
To switch the blower on:
► Insert the activation key.
► Unlock the retaining latch(1) by pushing it forward with
your thumb. Hold it in this unlocked position.
► Depress and hold the trigger switch lockout(2).
The retaining latch can be released and will stay in the
unlocked position.
► Squeeze the trigger switch(3) with your index finger.
Air flow will start.
0000-GXX-2269-A0
1
2
14 Switching the Blower On and Off
1
0000-GXX-2270-A0
2
3