Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
19
English
15 Checking the Controls
The motor will not switch on unless the retaining latch is
unlocked and the trigger switch lockout and trigger switch
are pressed at the same time.
14.2 Switching Off
WARNING
To reduce the risk of personal injury from unintended
activation or unauthorized use, switch off the motor and
remove the activation key before transporting or putting the
blower down.
To switch the blower off:
► Release the trigger switch and trigger switch lockout.
Once the trigger switch and trigger switch lockout have
been released, the retaining latch will return to its locked
position and activation of the trigger switch will be
blocked.
15.1 Testing the Controls
Before starting work, confirm that the retaining latch(1),
trigger switch lockout(2) and trigger switch(3) are
undamaged and functioning properly.
Retaining Latch (1), Trigger Switch Lockout (2) and Trigger
Switch (3)
WARNING
To help reduce the risk of injury from blown objects, always
wear proper eye protection while testing the controls. Keep
bystanders at least 16ft. (5m) away.
To test the controls:
► Remove the activation key.
► Unlock the retaining latch by pushing it forward with your
thumb.
► Hold the retaining latch in the unlocked position.
► Depress the trigger switch lockout and the trigger switch
momentarily.
► Release the retaining latch, trigger switch lockout and
trigger switch.
The retaining latch, trigger switch lockout and trigger
switch should return to their respective locked positions. If
they do not, take the blower to an authorized STIHL
servicing dealer to be repaired before use.
If you are able to activate the trigger switch without first
unlocking the retaining latch and depressing the trigger
switch lockout, take the blower to an authorized STIHL
servicing dealer to be repaired before use.
► Insert the activation key.
► Hold the blower firmly and unlock the retaining latch.
Depress the trigger switch lockout and trigger switch
momentarily.
The blower should switch on. If it does not, take the blower
to an authorized STIHL servicing dealer to be repaired
before use.
► Release the trigger switch.
The blower should switch off.
If the blower does not switch off after you release the
trigger switch, remove the activation key and take the
blower to an authorized STIHL servicing dealer to be
repaired before use.
15 Checking the Controls
1
0000-GXX-2270-A0
2
3