Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Charger Safety
- 7 Maintenance, Repair and Storage
- 8 General Warnings and Instructions
- 9 Before Starting Work
- 10 Charging the Blower
- 11 LED Diagnostics
- 12 Assembling the Blower
- 13 Inserting and Removing the Activation Key
- 14 Switching the Blower On and Off
- 15 Checking the Controls
- 16 During Operation
- 17 After Finishing Work
- 18 Transporting the Blower
- 19 Storing the Blower and Charger
- 20 Cleaning
- 21 Inspection and Maintenance
- 22 Troubleshooting Guide
- 23 Specifications
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Seguridad del cargador
- 7 Mantenimiento, reparación y almacenamiento
- 8 Advertencias e instrucciones generales
- 9 Antes de empezar a trabajar
- 10 Carga del soplador
- 11 Diagnóstico de LED
- 12 Armado del soplador
- 13 Inserción y retiro de la llave de activación
- 14 Encendido y apagado del soplador
- 15 Revisión de los controles
- 16 Durante el funcionamiento
- 17 Después de completar el trabajo
- 18 Transporte del soplador
- 19 Almacenamiento del soplador y el cargador
- 20 Limpieza
- 21 Inspección y mantenimiento
- 22 Guía de solución de problemas
- 23 Especificaciones
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-719-8621-A
23
English
22 Troubleshooting Guide
22.1 Troubleshooting
22 Troubleshooting Guide
Always remove the activation key before carrying out any inspection, cleaning or maintenance.
Condition LEDs on the
blower
Cause Remedy
3 LEDs flash
red.
Malfunction in
blower.
► Do not attempt to use. The blower has a malfunction and
must be checked by a servicing dealer.
Blower does not start
when switched on.
Activation key not
fully inserted.
► Remove the activation key, @ 13.2.
► Visually check the electrical contacts of the activation key.
► Reinsert the activation key, @ 13.1.
1 LED flashes
green.
Less than 20%
charge remaining.
► Charge the blower, @ 10.
3 LEDs glow
red.
Integrated battery
too hot.
► Remove the activation key, @ 13.2.
► Allow the blower to cool down gradually at ambient
temperatures of about 50°F to 68°F (10°C to 20°C).
Moisture in blower. ► Allow the blower to dry.
Blower cuts out
during operation.
3 LEDs glow
red.
Integrated battery
too hot.
► Remove the activation key, @ 13.2.
► Allow the blower to cool down gradually at ambient
temperatures of about 50°F to 68°F (10°C to 20°C).
Electrical
malfunction.
► Switch off the blower. Wait at least 5seconds and switch it
back on, @ 14.
Runtime is too short. Blower not fully
charged.
► Charge the blower, @ 10.
Useful life of
integrated battery
has been reached or
exceeded.
► Have the blower checked by an authorized STIHL servicing
dealer.
Integrated battery
too hot / too cold.
► Allow the blower to warm up or cool down gradually at
ambient temperatures of about 50°F to 68°F (10°C to
20°C).
Blower is not being
charged.
3 LEDs glow
red.
Integrated battery
too hot / too cold.
► Allow the blower to warm up or cool down gradually at
ambient temperatures of about 50°F to 68°F (10°C to
20°C).
► Operate the charger only in enclosed, dry rooms at ambient
temperatures of 32°F to 104°F (0°C to 40°C).