Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Battery Safety
- 8 Charger Safety
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Charging the Battery
- 12 LED Diagnostics
- 13 Mounting and Removing a Cutting Attachment
- 14 Inserting and Removing the Battery
- 15 Switching the Garden Shears On and Off
- 16 Checking the Controls
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting the Garden Shears and Battery
- 20 Storing the Garden Shears, Battery and Charger
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Replacement Parts and Equipment
- 26 Disposal
- 27 Limited Warranty
- 28 Trademarks
- 29 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta eléctrica
- 5.6 Uso y cuidado de la herramienta de baterías
- 5.7 Mantenimiento
- 5.8 Cortasetos/tijera de podar con advertencias de seguridad sobre las cuchillas para arbustos instaladas
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Seguridad de la batería
- 8 Seguridad del cargador
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Carga de la batería
- 12 Diagnóstico de LED
- 13 Montaje y retiro de un accesorio de corte
- 14 Colocación y extracción de la batería.
- 15 Encendido y apagado de la tijera de podar
- 16 Revisión de los controles
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte de la tijera de podar y de la batería
- 20 Almacenamiento de la tijera de podar, la batería y el cargador
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Piezas y equipos de repuesto
- 26 Eliminación
- 27 Garantía limitada
- 28 Marcas comerciales
- 29 Direcciones
0458-601-8621-A
15
English
6 IMPORTANT SAFETY INSTRUCTIONS
■ The cutting blades continue to move for a short period
after the trigger switch is fully released.
– Wait for the cutting blades to stop before walking
with the garden shears or putting them down.
■ In the event of an emergency:
– Switch off the motor immediately and remove the
battery.
■ Contacting foreign objects while cutting could damage the
cutting blades and may cause them to crack, chip, break
or jam. To reduce the risk of severe personal injury or
death from loss of control, and to reduce the risk of
damage to the garden shears:
– Inspect the material to be cut and the surrounding
area for stones, fence wire, metal or other foreign
objects before starting work. Do not use the garden
shears in areas where the cutting blades could
contact such objects.
– Take particular care when cutting next to, against or
near wire fences. Do not touch the wire with the
cutting blades.
– When working close to the ground, make sure that
no sand, grit or stones get between the cutting
blades.
– Do not cut any areas of the hedge, bush, shrub or
other vegetation that you cannot see.
■ To reduce the risk of injury to bystanders:
– Do not allow other persons in the general work area.
– If cutting the top of a taller shrubs, check the other
side of the shrub frequently for bystanders, animals
and obstructions.
■ Check the cutting blades at regular short intervals during
operation, or immediately if there is a change in cutting
behavior:
– Switch off the garden shears and remove the
battery.
– Check the condition, tightness and sharpness of the
cutting blades.
– Inspect the garden shears for loose parts (nuts,
screws, etc.) and for cracked, bent, warped or
damaged cutting blades. Replace damaged cutting
blades before using the garden shears.
– Always keep the cutting blades sharp.
■ To reduce blade friction and the buildup of dirt, which can
interfere with the proper functioning of the garden shears:
– STIHL recommends that you spray the cutting
blades with a resin solvent, such as STIHL Resin
Remover and Lubricant, before starting work.
DANGER
■ To reduce risk of electrocution:
– Never operate these garden shears in
the vicinity of any wires or cables that
may be carrying electric current.
– Do not rely on the garden shears'
insulation against electric shock.