Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Battery Safety
- 8 Charger Safety
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Charging the Battery
- 12 LED Diagnostics
- 13 Mounting and Removing a Cutting Attachment
- 14 Inserting and Removing the Battery
- 15 Switching the Garden Shears On and Off
- 16 Checking the Controls
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting the Garden Shears and Battery
- 20 Storing the Garden Shears, Battery and Charger
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Replacement Parts and Equipment
- 26 Disposal
- 27 Limited Warranty
- 28 Trademarks
- 29 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta eléctrica
- 5.6 Uso y cuidado de la herramienta de baterías
- 5.7 Mantenimiento
- 5.8 Cortasetos/tijera de podar con advertencias de seguridad sobre las cuchillas para arbustos instaladas
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Seguridad de la batería
- 8 Seguridad del cargador
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Carga de la batería
- 12 Diagnóstico de LED
- 13 Montaje y retiro de un accesorio de corte
- 14 Colocación y extracción de la batería.
- 15 Encendido y apagado de la tijera de podar
- 16 Revisión de los controles
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte de la tijera de podar y de la batería
- 20 Almacenamiento de la tijera de podar, la batería y el cargador
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Piezas y equipos de repuesto
- 26 Eliminación
- 27 Garantía limitada
- 28 Marcas comerciales
- 29 Direcciones
0458-601-8621-A
31
English
22 Inspection and Maintenance
handling the garden shears or the cutting blades, @ 6.4.
STIHL recommends having the cutting blades sharpened by
an authorized STIHL servicing dealer.
Although it is best to have the cutting blades sharpened by
a dealer, it is possible to use a flat, crosscut sharpening file
to sharpen the cutting blades.
Sharpen the cutting blades when cutting performance
begins to deteriorate, i.e., blades frequently snag on
branches or fail to cut material cleanly.
Shrub Blades
To sharpen the shrub blades with a file:
► Remove the shrub blades from the garden shears,
@ 13.2.
► Sharpen each cutting edge of the upper shrub cutting
blade with a sharpening file. Always file toward the cutting
edge with a forward motion. The file only sharpens on the
forward stroke. Lift off the blade on the backstroke.
► Only sharpen the cutting edges. Do not file blunt
projecting parts of the cutting attachment, or the cutting
blade guard. Make sure your sharpening stroke matches
the sharpening angle, @ 24.2.
► Turn the shrub blades over and sharpen the cutting edges
of the lower shrub cutting blade.
► Use a whetstone to remove any burrs from the cutting
edges. Remove as little material as possible.
► After sharpening, wipe away filing or grinding dust with a
dry or slightly dampened cloth and then spray the cutting
blades with a resin solvent, such as STIHL Resin
Remover and Lubricant.
Grass Blades
To sharpen the grass blades with a file:
► Remove the grass blades from the garden shears,
@ 13.2.
► Move the upper grass cutting blade fully in one direction
so that one side of the cutting edges is easily accessible.
► Sharpen each accessible cutting edge of the upper grass
cutting blade with a sharpening file. Always file toward the
cutting edge with a forward motion matching the
sharpening angle, @ 24.2. Sharpen on the forward
stroke. Lift off the blade on the backstroke.
► Only sharpen the cutting edges. Do not file blunt
projecting parts of the cutting attachment, or the cutting
blade guard. Make sure your sharpening stroke matches
the sharpening angle, @ 24.2.
► Move the upper grass cutting blade fully in the other
direction so that the other side of the cutting edges is
easily accessible and sharpen the rest of the cutting
edges.
► Use a whetstone to remove any burrs from the cutting
edges. Remove as little material as possible.
0000-GXX-A623-A0
0000-GXX-A624-A0