BA_U1_MS_270_280_86_01.fm Seite 0 Mittwoch, 31. Mai 2006 2:51 14 STIH) STIHL MS 441 C Instruction Manual Manual de instrucciones Warning! This saw is capabale of servere kickback which may cause serious or fatal injury. Only for users with extraordinary cutting needs and experience and training dealing with kickback. Chainsaws with significantly reduced kickback potential are available. STIHL recommends the use of STIHL reduced kickback bar and low kickback chain.
English / USA © ANDREAS STIHL AG & Co. KG, 2008 0458 152 8621 A. M0,2. A8. Rei. Printed in Germany Printed on chlorine-free paper. Printing inks contain vegetable oils; paper can be recycled. BA_SE_188_004_01_03.fm Contents Secondary Chain Braking System ................................ 2 Guide to Using this Manual .............. 3 Some Important Safety Precautions for Chain Saw Users ........................ 4 Safety Precautions and Working Techniques .......................................
English / USA Secondary Chain Braking System The chain brake can be activated in three ways: 2 1 150BA000 KN This STIHL chainsaw is equipped with a chain brake system that can be activated in three different ways. As before, the chain brake can be activated by the inertia of the front hand guard in certain kickback situations or manually by pushing the front hand guard toward the bar nose.
English / USA Guide to Using this Manual Pictograms All the pictograms attached to the machine are shown and explained in this manual. The operating and handling instructions are supported by illustrations. In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the symbols described below: Symbols in text Warning where there is a risk of an accident or personal injury or serious damage to property.
English / USA Some Important Safety Precautions for Chain Saw Users A. A Summary of Warnings on kickback and other Selected Risks – Taken Primarily from ANSI B 175.1 (See also the “Safety Precautions“ section of this Owner’s Manual) Do not rely exclusively upon the safety devices built into your saw. As a chainsaw user, you should take several steps to keep your cutting jobs free from accident or injury. 1.
English / USA 4. Use caution when handling fuel. Move the chainsaw at least 10 feet (3 m) from the fueling point before starting the engine. 5. Do not allow other persons to be near the chainsaw when starting or cutting with the chainsaw. Keep bystanders and animals out of the work area. 6. 7. 8. 9. Do not start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree. Keep all parts of your body away from the saw chain when the engine is running.
English / USA Safety Precautions and Working Techniques Because a chainsaw is a high-speed, fast-cutting power tool, special safety precautions must be observed to reduce the risk of personal injury. It is important that you read, fully understand and observe the following safety precautions and warnings. Read the instruction manual and the safety instructions periodically. Careless or improper use may cause serious or fatal injury. !Warning! Reactive forces, including kickback, can be dangerous.
English / USA !Warning! – Prolonged use of a power tool (or other machines) exposing the operator to vibrations may produce whitefinger disease (Raynaud's phenomenon) or carpal tunnel syndrome. These conditions reduce the hand's ability to feel and regulate temperature, produce numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis.
English / USA Wear an approved safety hard hat to reduce the risk of injury to your head. Chainsaw noise may damage your hearing. Wear sound barriers (ear plugs or ear mufflers) to help protect your hearing. Continual and regular users should have their hearing checked regularly. Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings (shouts, alarms, etc.) is restricted.
English / USA Fuel Your STIHL power tool uses an oilgasoline mixture for fuel (see the chapter on “Fuel” of your instruction manual). !Warning! Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and serious burn injury or property damage. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape from the fuel system.
English / USA Before Starting Take off the chain guard (scabbard) and inspect the saw for proper condition and operation. (See the maintenance chart near the end of the instruction manual.) !Warning! Always check your power tool for proper condition and operation before starting, particularly the throttle trigger, throttle trigger interlock, stop switch and cutting tool. The throttle trigger must move freely and always spring back to the idle position.
English / USA 001BA113 KN 001BA114 KN forces). Never attempt to start the chainsaw when the guide bar is in a cut or kerf. With the first recommended method, the chainsaw is started on the ground. Make sure the chain brake is engaged (see "Chain Brake" chapter in your instruction manual) and place the chainsaw on firm ground or other solid surface in an open area. Maintain good balance and secure footing.
English / USA Important Adjustments !Warning! To reduce the risk of personal injury from loss of control or contact with the running cutting tool, do not use your unit with incorrect idle adjustment. At correct idle speed, the cutting tool should not move. For directions on how to adjust idle speed, see the appropriate section of your instruction manual. If you cannot set the correct idle speed, have your STIHL dealer check your power tool and make proper adjustments and repairs.
English / USA 001BA082 KN !Warning! 001BA031 KN Position the chainsaw in such a way that your body is clear of the cutting attachment whenever the engine is running. Stand to the left of cut while bucking. !Warning To reduce the risk of injury from loss of control, never work on a ladder or any other insecure support. Never hold the machine above shoulder height. Do not overreach.
English / USA !Warning! !Warning! !Warning Inhalation of certain dusts, especially organic dusts such as mold or pollen, can cause susceptible persons to have an allergic or asthmatic reaction. Substantial or repeated inhalation of dust and other airborne contaminants, in particular those with a smaller particle size, may cause respiratory or other illnesses. This includes wood dust, especially from hardwoods, but also from some softwoods such as Western Red Cedar.
English / USA ! Warning! !Warning! !Warning! Inspect buffers periodically. Replace damaged, broken or excessively worn buffers immediately, since they may result in loss of control of the saw. A "sponginess" in the feel of the saw, increased vibration or increased "bottoming" during normal operation may indicate damage, breakage or excessive wear. Buffers should always be replaced in sets. If you have any questions as to whether the buffers should be replaced, consult your STIHL servicing dealer.
English / USA Reactive forces including kickback Kickback: !Warning! The greater the force of the kickback reaction, the more difficult it becomes for the operator to control the saw. Many factors influence the occurrence and force of the kickback reaction. These include chain speed, the speed at which the bar and chain contact the object, the angle of contact, the condition of the chain and other factors. The powerful force used to cut wood can be reversed and work against the operator.
English / USA a) Saws with a displacement of less than 3.8 cubic inches (62 cm³) – must, in their original condition, meet a 45° computer derived kickback angle when equipped with certain cutting attachments, – and must be equipped with at least two devices to reduce the risk of kickback injury, such as a chain brake, low kickback chain, reduced kickback bar, etc. b) Saws with a displacement of 3.
English / USA On models equipped with a rear-handleactivated chain brake the interlock lever and the throttle trigger on the rear handle act as a third means of activation. See the chapter entitled "Chain Brake" of your instruction manual. 001BA174 KN !Warning! When a kickback occurs, the guide bar may rotate around the front handle.
English / USA Low kickback saw chain and reduced kickback bars STIHL offers a variety of bars and chains. STIHL reduced kickback bars and low kickback chains are designed to reduce the risk of kickback injury. Other chains are designed to obtain higher cutting efficiency or sharpening ease but may result in higher kickback tendency. STIHL has developed a color code system to help you identify the STIHL reduced kickback bars and low kickback chains.
English / USA To avoid kickback STIHL green labeled reduced kickback bars are designed to reduce the risk of kickback injury when used with STIHL green labeled low kickback chains. The best protection from personal injury that may result from kickback is to avoid kickback situations: !Warning! When used with other, more aggressive chains, these bars may be less effective in reducing kickback. 1. Hold the chainsaw firmly with both hands and maintain a secure grip. Don’t let go. 2.
English / USA Cutting Techniques B = Pushback Felling Instructions: Felling Pushback occurs when the chain on the top of the bar is suddenly stopped when it is pinched, caught or encounters a foreign object in the wood. The reaction of the chain may drive the saw rapidely straight back toward the operator and may cause loss of saw control. Pushback frequently occurs when the top of the bar is used for cutting. To avoid pushback 1.
English / USA B Buttress roots C 001BA146 KN 45° A If the tree has large buttress roots, cut into the largest buttress vertically first (horizontally next) and remove the resulting piece. C 001BA143 KN B 001BA040 KN 45° Gunning sight Conventional cut First clear the tree base and work area from interfering limbs and brush and clean its lower portion with an ax. C = felling notch - determines the direction of the fall Then, establish two paths of escape (B) and remove all obstacles.
English / USA C D C 001BA144 KN 001BA143 KN 001BA150 KN D Open-face technique Making sapwood cuts D = Felling cut C = felling notch - determines the direction of the fall : Conventional and open-face technique: For an open-face cut: : Properly place felling notch perpendicular to the line of fall, close to the ground. : Cut down at app. 50-degree angle to a depth of app.1/5 to 1/4 of the trunk diameter. : Make second cut from below at app. 40 degree angle.
English / USA Drive wedges into the felling cut where necessary to control the fall. E !Warning! If the tip of the bar contacts a wedge, it may cause kickback. Wedges should be of wood or plastic - never steel, which can damage the chain. E = Hinge 24 : Helps control the falling tree. : Do not cut through the hinge – you could lose control of the direction of the fall.
English / USA Plunge-cut method Timber having a diameter more than twice the length of the guide bar requires the use of the plunge-cut method before making the felling cut. First, cut a large, wide felling notch. Make a plunge cut in the center of the notch. 2 1 001BA148 KN 4 Felling cut for large diameter trees: !Warning! Felling a tree that has a diameter greater than the length of the guide bar requires use of either the sectioning felling cut or plunge-cut method.
English / USA !Warning! Enlarge the plunge cut as shown in the illustration. !Warning! There is an extreme danger of kickback at this point. Extra caution must be taken to maintain control of the saw. To make the felling cut, follow the sectioning method described previously. If you are inexperienced with a chainsaw, plunge-cutting should not be attempted. Seek the help of a professional.
English / USA 2 001BA151 KN 1 Bucking Bucking is cutting a log into sections. !Warning! When bucking, do not stand on the log. Make sure the log will not roll downhill. If on a slope, stand on the uphill side of the log. Watch out for rolling logs. Cut only one log at a time. Shattered wood should be cut very carefully. Sharp slivers of wood may be caught and flung in the direction of the operator of the saw.
English / USA MAINTENANCE, REPAIR AND STORING !Warning! !Warning! Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, if you make a warranty claim for a component which has not been serviced or maintained properly or if nonapproved replacement parts were used, STIHL may deny coverage. Do not attempt any maintenance or repair work not described in your instruction manual.
English / USA Mounting the Bar and Chain The chainsaw should also be returned immediately for maintenance whenever the brake system cannot be thoroughly cleaned or there is a change in its operating characteristics. For any maintenance of the emission control system please refer to the maintenance chart and to the limited warranty statement near the end of the instruction manual. Store chainsaw in a dry place and away from children.
English / USA Tensioning the Saw Chain 6 Wear work gloves to protect your hands from the sharp cutters. : 30 7 : 1 Fit the guide bar over the studs (7) – cutting edges on top of bar must point to right – and engage the peg of the tensioner slide in locating hole (8) –- place the chain over sprocket (9) at the same time. : Press down the throttle trigger interlock to release the chain brake.
English / USA Checking Chain Tension Fuel 143BA007 KN This engine is certified to operate on unleaded gasoline and the STIHL twostroke engine oil at a mix ratio of 50:1. : Shut off the engine. : Wear work gloves to protect your hands. : Pull the hand guard toward the rear handle. : Press down the throttle trigger interlock to release the chain brake.
English / USA Fueling Fuel mix ages Gasoline Oil (STIHL 50:1 or equivalent high-quality oils) Before fueling, clean the filler cap and the area around it to ensure that no dirt falls into the tank. US gal. 1 2 1/2 5 US fl.oz 2.6 6.4 12.8 Always position the machine so that the filler cap points upwards. 32 : Raise the grip until it is upright. : Turn the cap counterclockwise (approx. a quarter turn). : Remove the filler cap.
English / USA Chain Lubricant For automatic and reliable lubrication of the chain and guide bar – use only an environmentally compatible quality chain and bar lubricant with non-fling additive or the rapidly biodegradable STIHL BioPlus is recommended. 001BA162 KN Closing the cap Fit the cap - grip upright -marks must line up. : Turn the cap clockwise as far as stop (approx. a quarter turn). 165BA003 KN : Biological chain oil must be resistant to aging (e.g.
English / USA Filling Chain Oil Tank Checking Chain Lubrication Waste oil does not have the necessary lubricating properties and is unsuitable for chain lubrication. : Thoroughly clean the oil filler cap and the area round it to ensure that no dirt falls into the tank. : Remove the filler cap. : Refill the chain oil tank every time you refuel. : Close the filler cap. There must still be a small amount of oil in the oil tank when the fuel tank is empty.
English / USA Chain Brake The chain brake system on your saw has two functions: : : Standard STIHL chain brake and STIHL rear-handle-activated secondary braking system The standard STIHL chain brake utilizes the front hand guard as the activating mechanism and is designed to stop the chain within fractions of a second. The secondary braking system, on the other hand, is designed to stop chain rotation within a second of you completely letting go of the rear handle.
English / USA Always disengage chain brake before accelerating engine and before starting cutting work. The only exception to this rule is when you check operation of the chain brake. High revs with the chain brake engaged (chain locked) will quickly damage the powerhead and chain drive (clutch, chain brake). The chain brake is designed to be activated also by the inertia of the front hand guard if the forces are sufficiently high.
English / USA Winter Operation - At temperatures below +50 °F (+10 °C) preheat carburetor as follows: The carburetor is now heated via the preheating plate – this helps avoid icing up. Fitting Cover Plate (special accessory) At temperatures above +68°F (+20°C): Always return the shutter to the summer position (s). This is essential to avoid engine running problems and overheating.
English / USA Starting / Stopping the Engine Information Before You Start Starting Procedure STOP STOP 0 0 001BA140 KN : The four positions of the Master Control lever $ = Engine off – ignition is switched off. # = Normal run position – engine runs or can fire. To move the Master Control lever from # to n or l, press down the throttle trigger interlock and squeeze throttle trigger at the same time. n=Warm start – this position is used to Press in the button to open the decompression valve.
English / USA : Place your saw on the ground. Make sure you have a firm footing – check that chain is not touching any object or the ground. Bystanders must be well clear of the general work area of the saw! : Hold the saw firmly on the ground with your left hand on the front handle – your thumb should be under the handle. : Put your right foot into the rear handle and press down. MS 441 C : : Alternative method of starting: Hold the rear handle tightly between your legs, just above the knees.
English / USA At very low outside temperatures: : Allow engine to warm up at part throttle. : Change over to winter operation if necessary – see “Winter Operation”. STOP 0 To shut down the engine: : Move Master Control lever to $. If fuel tank has been run until empty and then refueled: When the engine begins to fire: : Press in the decompression valve button again.
English / USA Operating Instructions If the engine doesn’t start: : Unscrew and dry off the spark plug. During break-in period If you did not move the Master Control lever from cold start l to warm start n quickly enough after the engine began to fire, the combustion chamber is flooded. : Set the Master Control lever to $ : Crank the engine several times with the starter to clear the combustion chamber.
English / USA During operation Check chain tension frequently A new chain has to be retensioned more often than one that has been in use for some time. Chain cold: Tension is correct when chain fits snugly against the underside of the bar and can still be pulled along the bar by hand. Retension if necessary – see “Tensioning the Saw Chain”. Chain at operating temperature: The chain stretches and begins to sag. The drive links must not come out of the bar groove – the chain may otherwise jump off the bar.
English / USA Air Filter System Chain type 2 Picco Rapid Rapid 3 Rapid Pitch Minimum groove depth 3/8“ P 0.20" (5.0 mm) 1/4“ 0.16" (4.0 mm) 3/8“; 0.325“ 0.24" (6.0 mm) 0.404“ 0.28" (7.0 mm) 1 3 001BA119 KN If groove depth is less than specified: : Turn the bar over – every time you sharpen the chain and every time you replace the chain – this helps avoid one-sided wear, especially at the nose and underside of the bar.
English / USA Removing the Air Filter Cleaning Standard Filter : Use the combination wrench to open the fasteners (1) in the direction of the arrows. If there is a noticeable loss of engine power: : Remove the carburetor box cover (2). STIHL filters (standard and HD) have a long service life when kept in a dry condition. Always use STIHL filters in dry condition. 137BA013 KN : Dirty air filters reduce engine power, increase fuel consumption and make starting more difficult.
English / USA Cleaning HD Filter 2 2 1 If there is a noticeable loss of engine power: In case of stubborn dirt or sticky filter fabric: : : Clean the felt prefilter (1). After cleaning the prefilter several times: : Separate the filter components. : Knock the HD filter (2) out on the palm of your hand and blow it out with compressed air from the inside outward. : : Wash filter with STIHL universal cleaner or in a fresh, non-flammable solution (e.g. warm soapy water).
English / USA Motor Management Adjusting the Carburetor Exhaust emissions are controlled by the design of the fundamental engine parameters and components (e.g. carburation, ignition, timing and valve or port timing) without the addition of any major hardware. General Information Standard Setting The carburetor comes from the factory with a standard setting. This setting provides an optimum fuel-air mixture under most operating conditions.
English / USA Adjusting Idle Speed 219BA028 KN Erratic idling behavior, poor acceleration (although L screw is open 1/4 turn) Check the standard setting. : Turn the idle speed screw (LA) slowly clockwise – as far as stop or until the chain begins to run – then turn the screw back 11/2 turn. If the chain continues moving when the engine is idling, have your saw checked and repaired by your servicing dealer.
English / USA Spark Arresting Screen in Muffler Checking the Spark Plug : If the engine is down on power, check the spark arresting screen* in the muffler. If engine is down on power, difficult to start or runs poorly at idling speed, first check the spark plug. : Wait for the muffler to cool down. : Remove spark plug – see "Starting / Stopping the Engine". : Clean dirty spark plug. : Check electrode gap (A) and readjust if necessary – see "Specifications".
English / USA Replacing Starter Rope and Rewind Spring : Push the hand guard upward. : Pull the underside of the fan housing away from the crankcase and remove it downward. 2 Use a screwdriver to pry the rope out of the starter grip. : Remove the remaining rope from the rotor and grip. 213BA019 KN Remove the screws (1). 000BA036 TR 1 : : Thread the new rope through the top of the starter grip.
English / USA 2 3 5 6 : Fit the pawls (4) in the rope rotor. : Fit the washer (3) on the starter post. : Use a screwdriver or suitable pliers to install the spring clip (2) on the starter post and engage it on the pawls’ pegs – the spring clip must point clockwise as shown in the illustration. 213BA020 KN 7 Thread the rope through the top of the guide bush (5), pull it through the rotor (6) and secure it with a simple overhand knot. : Coat rope rotor bearing bore with resin-free oil.
English / USA Storing the Machine For periods of about 3 months or longer: Replacing a Broken Rewind Spring The bits of spring might still be under tension and could fly apart when you take them out of the fan housing. To reduce risk of injury, wear eye and face protection and work gloves. : : : Drain and clean the fuel tank in a well ventilated area. : Dispose of remaining fuel and cleaning solution properly in accordance with local environmental requirements.
English / USA Checking and Replacing Chain Sprocket : : Remove the chain sprocket cover, chain and guide bar. Installing spur sprocket / rim sprocket 5 Disengage the chain brake: Pull hand guard toward the front handle. : 6 2 1 4 – Replace the chain sprocket after using two Oilomatic chains. – Replace sooner if the wear marks on the sprocket are deeper than approx. 0.02 in (0,5 mm) since this would reduce the life of the chain.
English / USA Maintaining and Sharpening Saw Chain Correctly sharpened chain : Clean the chain. : Check the chain for cracks in the links and damaged rivets. : Replace any damaged or worn parts of the chain and match the new parts to the shape and size of the original parts. It is absolutely essential to comply with the angles and dimensions specified below.
English / USA 80° 35° : Use a file holder A file holder (special accessory) must be used for manual resharpening (see table "Sharpening Tools"). The correct filing angles are marked on the file holder. 54 0° 90° Use a STlHL filing gauge (special accessory – see table "Sharpening Tools"). This is a universal tool for checking the filing and side plate angles, depth gauge setting and cutter length. It also cleans the guide bar groove and oil inlet holes.
English / USA The file only sharpens on the forward stroke – lift the file off the cutter on the backstroke. : Avoid touching the tie straps and drive links with the file. : Rotate the file at regular intervals while filing to avoid one-sided wear. : Use a piece of hardwood to remove burrs from cutting edge. : Check angles with the filing gauge. All cutters must be the same length. If the cutters are not the same length, they will have different heights.
English / USA : File the top of the depth gauge parallel to the stamped service marking (see arrow) – but do not lower the highest point of the depth gauge in this process. The kickback tendency of the chainsaw is increased if the depth gauges are too low. The other parts of the triple-humped tie strap and humped drive link must not be filed since this may increase the kickback tendency of the chainsaw.
English / USA Complete machine Throttle trigger, trigger interlock, Master Control Chain brake Pickup body/filter in fuel tank X Visual inspection (condition, leaks) Check operation X X Check operation X X X Check X Clean, replace filter element X X X X X Clean Check X Inspect, also check sharpness X X Check chain tension X X X Sharpen X Check (wear, damage) X Clean and turn over X Deburr X Replace Chain sprocket Air filter Anti-vibration elements X X Check X Clean X X
as required if damaged if problem every 12 months monthly weekly after each refueling stop after finishing work or daily Please note that the following maintenance intervals apply for normal operating conditions only. If your daily working time is longer than normal or cutting conditions are difficult (very dusty work area, resin-rich wood, tropical wood etc.), shorten the specified intervals accordingly. If you only use the saw occasionally, extend the intervals accordingly.
English / USA Main Parts of the Saw 1 Carburetor box cover with clips 2 Carburetor adjusting screws 3 Shutter (summer and winter operation) 4 Spark plug boot 5 Decompression valve (automatically resetting) 6 Chain brake 7 Chain sprocket 8 Chain sprocket cover 9 Chain catcher 10 Chain tensioner 11 Bumper spike 12 Guide bar 13 Oilomatic saw chain # Serial number 14 Oil filler cap 15 Muffler 16 Front hand guard 17 Front handle (handlebar) 18 Starter grip 19 Fuel filler cap 20 Master Control lever (On/Off/S
English / USA Definitions 1. Carburetor Box Cover Twist Lock Lock for carburetor box cover. 2. Carburetor Adjusting Screws For fine tuning the carburetor. 3. Shutter With summer and winter positions. Carburetor is heated in winter position. 4. Spark Plug Boot Connects the spark plug with the ignition wire. 5. Decompression Valve (automatically resetting) Reduces compression resistance to make starting easier - when activated 6. 7. 8. 9.
English / USA Specifications EPA / CEPA: The Emission Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category A = 300 hours B = 125 hours C = 50 hours CARB: The Emission Compliance Period used on the CARB Air Index Label indicates the terms: Extended = 300 hours Intermediate = 125 hours Moderate = 50 hours Engine STIHL single cylinder two-stroke engine Displacement 4.
English / USA Since new bar/chain combinations may be developed after publication of this manual, ask your STIHL dealer for the latest STIHL recommendations.
English / USA Maintenance and Repairs Users of this unit should carry out only the maintenance operations described in this manual. Other repair work may be performed only by authorized STIHL service shops. Warranty claims following repairs can be accepted only if the repair has been performed by an authorized STIHL servicing dealer using original STIHL replacement parts. Original STlHL parts can be identified by the STlHL part number, the STIHl logo and, in some cases, by the STlHL parts symbol (.
English / USA Not for California: STIHL Incorporated Federal Emission Control Warranty Statement Your Warranty Rights and Obligations Manufacturer's Warranty Coverage: The U.S. Environmental Protection Agency (EPA) and STIHL Incorporated are pleased to explain the Emission Control System Warranty on your equipment type engine. In the U.S. new 1997 and later model year small off-road equipment engines must be designed, built and equipped, at the time of sale, to meet the U.S.
English / USA If any emission related part on your engine is defective, the part will be replaced by STIHL Incorporated at no cost to the owner. Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of "repair or replace as necessary" will be warranted for the warranty period.
English / USA Trademarks Some of STIHL’s Common Law Trademarks STIHL PICCO™ q BioPlus™ STIHL PowerSweep™ ( Easy2Start™ STIHL Precision Series™ EasySpool™ STIHL Protech™ ElastoStart™ STIHL RAPID™ 4-MIX® Ematic /Stihl-E-Matic™ STIHL SuperCut™ AUTOCUT® FixCut™ STIHL Territory™ EASYSTART® HT Plus™ TapAction™ OILOMATIC® IntelliCarb™ TrimCut™ STIHL Cutquik® Master Control Lever™ STIHL DUROMATIC® Micro™ STIHL Farm Boss® Pro Mark™ STIHL Registered Trademarks STIHL ® The color combi
español / EE.UU © ANDREAS STIHL AG & Co. KG, 2008 0458 152 8621 A. M0,2. A8. Rei. Printed in Germany Impreso en papel sin cloro. Las tintas contienen aceites vegetales,el papel es reciclable. BA_SE_188_004_31_03.fm Contenido Sistema de freno de la cadena auxiliar ............................................ 68 Guía para el uso de este manual ... 69 Algunas importantes medidas de seguridad para los usuarios de la motosierra .............................. 70 Medidas de seguridad y técnicas de manejo ....
español / EE.UU Sistema de freno de la cadena auxiliar El sistema de freno de la cadena puede activarse de tres maneras: 2 1 150BA000 KN Esta motosierra STIHL cuenta con un sistema de freno de la cadena que puede activarse en tres maneras distintas. Igual que antes, el freno de la cadena puede accionarse por la inercia del protector delantero de la mano en ciertas situaciones de contragolpe o manualmente empujando el protector delantero de la mano hacia la punta de la espada.
español / EE.UU Guía para el uso de este manual Pictogramas Todos los pictogramas que se encuentran en la máquina se muestran y explican en este manual. Las instrucciones de uso y manipulación vienen acompañadas de ilustraciones. Símbolos en el texto Los pasos individuales o procedimientos descritos en el manual pueden estar señalados en diferentes maneras: : Un punto identifica un paso o procedimiento sin referencia directa a una ilustración.
español / EE.UU Algunas importantes medidas de seguridad para los usuarios de la motosierra A.
español / EE.UU 4. Actúe con cautela cuando maneje el combustible. Aléjese con la motosierra una distancia de por lo menos 10 m (3 pies) del punto de abastecimiento de combustible antes de arrancar el motor. 10. No maneje nunca una motosierra que está dañada, mal ajustada o que no fue armada debidamente. Asegúrese que la cadena de la sierra se detiene al soltar el gatillo de aceleración. 5. No deje que otras personas se encuentren cerca de la motosierra durante las operaciones de arranque o corte.
español / EE.UU Medidas de seguridad y técnicas de manejo Dado que la motosierra es una herramienta de corte que funciona a gran velocidad, es necesario tomar medidas especiales de seguridad para reducir el riesgo de lesiones. Es importante que usted lea, comprenda bien y respete las siguientes advertencias y medidas de seguridad. Lea el manual de instrucciones y las instrucciones de seguridad periódicamente. El uso descuidado o inadecuado puede causar lesiones graves o incluso mortales.
español / EE.UU !Advertencia! El uso prolongado de una herramienta motorizada (u otras máquinas) expone al operador a vibraciones que pueden provocar el fenómeno de Raynaud (dedos blancos) o el síndrome del túnel del carpio. Estas condiciones reducen la capacidad de las manos de sentir y regular la temperatura, producen entumecimiento y ardor y pueden provocar trastornos nerviosos y circulatorios, así como necrosis de los tejidos.
español / EE.UU Use un casco aprobado para reducir el riesgo de lesionarse la cabeza. El ruido de la motosierra puede dañar sus oídos. Siempre use amortiguadores del ruido (tapones u orejeras) para protegerse los oídos. Los usuarios constantes y regulares deben someterse con frecuencia a un examen o control auditivo. Esté especialmente alerta y tenga cuidado cuando se usa protectores de oídos, ya que los mismos reducen la posibilidad de oír señales de advertencia (gritos, alarmas, etc.).
español / EE.UU Combustible Su herramienta motorizada de STIHL utiliza una mezcla de aceite y gasolina como combustible (vea el capítulo "Combustible" en el manual de instrucciones). !Advertencia! La gasolina es un combustible muy inflamable. Si se derrama y arde a causa de una chispa u otra fuente de ignición, puede provocar un incendio y quemaduras graves o daños a la propiedad. Tenga sumo cuidado cuando manipule gasolina o la mezcla de combustible.
español / EE.UU Consulte el capítulo "Llenado de combustible" en el manual de instrucciones. Antes de arrancar Quite el protector de la cadena (la funda) e inspeccione la motosierra para verificar que está en buenas condiciones de funcionamiento. (Consulte la tabla de mantenimiento cerca del final de este manual de instrucciones.
001BA113 KN 001BA114 KN español / EE.UU Con el primer método recomendado, la motosierra se arranca apoyada en el suelo. Asegúrese que el freno de la cadena esté aplicado (vea el capítulo "Freno de la cadena" en el manual de instrucciones) y apoye la motosierra sobre terreno firme u otra superficie sólida en un lugar abierto. Mantenga el equilibrio y elija un buen punto de apoyo para los pies. Agarre el mango delantero firmemente con la mano izquierda y haga presión hacia abajo.
español / EE.UU Ajustes importantes !Advertencia! Para reducir el riesgo de lesiones personales debido a la pérdida de control o al contacto con la herramienta de corte en movimiento, no use una máquina cuyo ralentí está mal regulado. Cuando el ralentí está correctamente regulado, la herramienta de corte no debe moverse. Para instrucciones acerca de cómo ajustar la velocidad de ralentí, vea la sección correspondiente del manual de instrucciones.
español / EE.UU 001BA031 KN 001BA082 KN !Advertencia! !Advertencia Para reducir el riesgo de lesiones causadas por la pérdida del control, nunca trabaje sobre una escalera o cualquier otra superficie de soporte poco seguro. Nunca mantenga la máquina a una altura más arriba de los hombros. No trate de alcanzar más lejos de lo debido.
español / EE.UU !Advertencia! !Advertencia! !Advertencia La inhalación de ciertos polvos, especialmente los polvos orgánicos, tales como el moho o polen, puede provocar reacciones alérgicas o asmáticas en las personas sensibles. La inhalación repetida o de grandes cantidades de polvo u otros contaminantes del aire, especialmente los de partículas pequeñas puede causar enfermedades respiratorias o de otro tipo.
español / EE.UU ! Advertencia! Inspeccione los amortiguadores periódicamente. Sustituya de inmediato los que estén dañados, rotos o muy desgastados, ya que pueden causar la pérdida del control de la sierra. Si usted siente una "esponjosidad" en la sierra, aumento de la vibración o de tendencia al "hundimiento" durante el manejo normal, puede indicar algún daño, rotura o exceso de desgaste. Los amortiguadores siempre deben sustituirse en juegos.
español / EE.UU Fuerzas reactivas, incluido el contragolpe Contragolpe: El contragolpe puede ocurrir cuando la cadena en movimiento cerca del cuadrante superior de la punta de la espada toca un objeto sólido o queda !Advertencia! aprisionada. La gran fuerza utilizada para cortar madera puede cambiar de sentido y actuar contra el operador.
español / EE.UU a) Las sierras con una cilindrada inferior a 62 cm³ (3,8 pulg³) – deben tener, en su condición original, un ángulo de contragolpe de 45° calculado por computadora cuando están equipadas con ciertos accesorios de corte, y deben tener por lo menos dos dispositivos para reducir el riesgo de lesiones por contragolpe, tales como un freno de la cadena, cadena de bajo contragolpe, espada de contragolpe reducido, etc.
español / EE.UU En los modelos equipados con un freno de la cadena activado por el mango trasero, la palanca de bloqueo y el gatillo de aceleración en el mango trasero actúan como un tercer medio de activación. Vea el capítulo titulado "Freno de la cadena" en el manual de instrucciones. 001BA174 KN !Advertencia! Cuando ocurre un contragolpe, la espada puede girar alrededor del mango delantero.
español / EE.UU Cadena de aserrado de bajo contragolpe y espadas de contragolpe reducido STIHL ofrece una variedad de espadas y cadenas. Las espadas de contragolpe reducido y las cadenas de bajo contragolpe de STIHL están diseñadas para reducir el riesgo de lesiones causadas por contragolpe. Otras cadenas están diseñadas para obtener un rendimiento de corte mayor o para facilitar el afilado, pero pueden producir una mayor tendencia a los contragolpes.
español / EE.UU Una cadena roma o mal afilada puede reducir o anular los efectos de las características del diseño que deben reducir la fuerza de contragolpe. Una reducción o afilado incorrecto de los calibradores de profundidad o la alteración de la forma de las cuchillas puede aumentar la posibilidad y la fuerza potencial de un contragolpe. Siempre corte con una cadena bien afilada.
español / EE.UU El tirón también se puede reducir colocando cuñas para abrir la entalla o el corte. B = Rechazo Técnicas de corte Tala La tala consiste en cortar un árbol hasta que caiga. Antes de talar, estudie cuidadosamente todas las condiciones que pueden afectar la dirección de la caída. 001BA038 KN !Advertencia! B El rechazo ocurre cuando la cadena en la parte superior de la espada se detiene repentinamente cuando queda aprisionada, retenida o choca con algún objeto extraño en la madera.
español / EE.UU B Raíces de zancos grandes C 001BA146 KN 45° A 45° C 001BA143 KN B 001BA040 KN Si el árbol tiene raíces de zancos grandes, corte primero en el zanco más grande verticalmente (después horizontalmente) y retire el trozo cortado. Mira Corte convencional Primero, despeje todas las ramas y matorrales de la base del árbol y lugar de trabajo y limpie la parte inferior con un hacha. Después, establezca dos rutas de escape (B) y retire todos los obstáculos.
español / EE.UU C D C 001BA144 KN 001BA150 KN 001BA143 KN D Técnica de cara libre Para hacer cortes de albura D = Corte de tala C = entalla de tala - determina el sentido de caída del árbol : En árboles de tamaño mediano o más grandes, haga cortes a ambos lados del tronco, a la misma altura que el corte de tala subsiguiente. Técnica convencional y de cara libre: : Comience de 2,5 a 5 cm (1 a 2 pulg) más arriba que el centro de la entalla de tala. : Corte no más del ancho de la espada.
español / EE.UU Inserte cuñas en el corte de tala donde sea necesario para controlar la caída. !Advertencia! E Si la punta de la espada hace contacto con una cuña, puede producirse un contragolpe. Las cuñas deben ser de madera o de plástico, pero jamás de acero porque se dañaría la cadena. E = Eje de inclinación 90 : Ayuda a controlar la caída del árbol. : No corte a través del eje – podría perder el control del sentido de la caída.
español / EE.UU Método de corte por penetración La madera cuyo diámetro es más del doble del largo de la espada requiere el uso del método de corte por penetración antes de hacer el corte de tala. Primero, corte una entalla de tala grande y ancha. Haga un corte por penetración en el centro de la entalla.
español / EE.UU !Advertencia! Agrande el corte por penetración como se muestra en la ilustración. !Advertencia! En este momento existe un gran peligro de que ocurra contragolpe. Preocúpese de mantener el control de la sierra. Para hacer el corte de tala, emplee el método de corte por secciones descrito anteriormente. Si no tiene experiencia en el manejo de una motosierra, no intente hacer el corte por penetración. Pida la ayuda de un profesional.
español / EE.UU 2 001BA151 KN 1 Tronzado El tronzado consiste en cortar un tronco en secciones. !Advertencia! Durante el tronzado, no se suba al tronco. Asegúrese que el tronco no vaya a rodar cerro abajo. Si se encuentra en una ladera, sitúese cerro arriba del tronco. Esté atento a los troncos que pueden rodar. Corte solamente un tronco a la vez. La madera astillada deberá cortarse con mucho cuidado. Las astillas afiladas pueden atraparse y salir lanzadas hacia el operador.
español / EE.UU MANTENIMIENTO, REPARACION Y ALMACENAMIENTO Los trabajos de mantenimiento, reemplazo o reparación de los dispositivos y sistemas de control de emisiones de escape pueden ser realizados por cualquier taller o técnico de motores no diseñados para vehículos. Sin embargo, si usted está reclamando cobertura de garantía para algún componente que no ha sido reparado o mantenido debidamente, o cuando se utilizan repuestos no autorizados, STIHL puede denegar la garantía.
español / EE.UU Montaje de la barra y la cadena MS 441 C 1 2 En esta motosierra se pueden usar cadenas de pasos diferentes, dependiendo de la rueda dentada de la cadena (vea las "Especificaciones"): 143BA034 KN 3 : El paso de la cadena (1) debe coincidir con el paso de la rueda dentada y la barra guía (para Rollomatic). El tamaño del eslabón impulsor (2) debe coincidir con el ancho de la ranura de la barra (3).
español / EE.UU Tensión de la cadena de sierra 6 : : : Use guantes para proteger las manos de los cortadores afilados. : Coloque la cadena – empiece por la punta de la barra. : : 96 7 Coloque la barra guía sobre los espárragos (7) – los bordes de corte en la parte superior de la barra deben quedar apuntando hacia la derecha – e inserte la espiga del tensor deslizante en el agujero localizador (8); al mismo tiempo, coloque la cadena sobre la rueda dentada (9).
español / EE.UU Revisión de tensión de la cadena Combustible 143BA007 KN Este motor está certificado para funcionar con una mezcla de 50 a 1 de gasolina sin plomo y aceite STIHL para motores de dos tiempos. : Apague el motor. : Póngase guantes de trabajo. : Tire del protector de la mano hacia el mango trasero. : Empuje hacia abajo el bloqueo del gatillo de aceleración para soltar el freno de cadena.
español / EE.UU Llenado de combustible Duración de la mezcla de combustible gal EE.UU. 1 2 1/2 5 Aceite (STIHL 50:1 ó aceite de calidad equivalente) oz fl EE.UU. 2.6 6.4 12.8 Deseche los envases vacíos usados para mezclar el aceite únicamente en vertederos autorizados para ello. 98 Antes de llenar la máquina con combustible, limpie a fondo la tapa de llenado y la zona alrededor del mismo para evitar la entrada de tierra al tanque.
español / EE.UU Lubricante de la cadena Para una lubricación automática y segura de la cadena y la barra guía – se recomienda el uso exclusivo de un lubricante para cadena y barra guía no dañino para el ambiente con aditivo antisalpicaduras o el aceite STIHL Bioplus. : Coloque la tapa, con la empuñadura en posición vertical y las marcas alineadas : Gire la tapa en sentido horario hasta donde tope (aprox.
español / EE.UU Llenado del tanque de aceite de la cadena El aceite de desecho no tiene las propiedades lubricantes necesarias y no es adecuado para la lubricación de cadenas. : Limpie a fondo la tapa de llenado de aceite y la zona alrededor de la misma para evitar la entrada de suciedad al tanque. : Quite la tapa de llenado. : Llene el tanque de aceite de la cadena cada vez que se llene con combustible la máquina. : Cierre la tapa de llenado.
español / EE.UU Freno de la cadena El sistema de freno de la cadena de su motosierra tiene dos funciones: : : Freno de la cadena estándar de STIHL Sistema de freno auxiliar activado par mango trasero de STIHL El freno de la cadena estándar de STIHL emplea el protector delantero de la mano como el mecanismo activador y está diseñado para detener la cadena en una fracción de segundo.
español / EE.UU Siempre desconecte el freno de la cadena antes de acelerar el motor y antes de iniciar el trabajo de corte. La única excepción a esta regla es cuando se está probando el funcionamiento del freno de la cadena. El funcionamiento a velocidad alta con el freno de la cadena aplicado (cadena trabada) dañará rápidamente el motor y el mando de la cadena (embrague, freno de la cadena).
español / EE.UU Manejo durante el invierno - A temperaturas bajo +10°C (+50°F), precaliente el carburador de la siguiente manera: Ahora, la placa de precalentamiento calienta el carburador – esto ayuda a evitar la formación de hielo en el carburador. Colocación de la placa de cierre (accesorio especial) A temperaturas sobre +20°C (+68°F): Siempre vuelva a colocar el obturador en la posición de verano (s). Esto es esencial para evitar problemas de funcionamiento y sobrecalentamiento del motor.
español / EE.UU Información previa al arranque Arranque / parada del motor Procedimiento de arranque STOP STOP 0 0 001BA140 KN : Presione el botón para abrir la válvula de descompresión. La válvula de descompresión se cierra tan pronto el motor se enciende. : Por esta razón se debe oprimir el botón antes de cada intento de arranque.
español / EE.UU : Coloque la motosierra sobre el suelo. Asegúrese de tener los pies bien apoyados – verifique que la cadena no esté en contacto con ningún objeto ni con el suelo. Las personas ajenas al trabajo deben mantenerse alejadas de la zona general de uso de la sierra. : Sujete firmemente la sierra en el suelo con la mano izquierda en el mango delantero – el pulgar debe quedar debajo del mango. : Ponga el pie derecho en el mango trasero y presione hacia abajo.
español / EE.UU A temperaturas ambiente muy bajas: STOP : Deje que el motor se caliente a aceleración parcial. : De ser necesario, cambie al ajuste para uso durante el invierno – vea "Manejo durante el invierno". 0 Para apagar el motor: : Mueva la palanca de control maestro a $. Si se ha dejado que se agote el combustible y se ha vuelto a llenar el tanque: Cuando el motor empieza a encenderse: : Presione el botón de la válvula de descompresión otra vez.
español / EE.UU Instrucciones de manejo Si el motor no arranca: : Destornille y seque la bujía. Durante el período de rodaje Si no se mueve la palanca de control maestro de la posición de arranque frío a la de arranque caliente n en un tiempo suficientemente corto después que el motor ha empezado a encenderse, la cámara de combustión se encuentra ahogada. : Mueva la palanca de control maestro a $ : Haga girar el motor varias veces con el arrancador para despejar la cámara de combustión.
español / EE.UU Durante el funcionamiento Revise frecuentemente la tensión de la cadena Es necesario volver a tensar las cadenas nuevas con mayor frecuencia que las que han estado en uso por algún tiempo. Cadena fría: La tensión es correcta cuando la cadena encaja ajustadamente contra la parte inferior de la barra y todavía puede ser tirada a lo largo de la barra con la mano. Ténsela nuevamente de ser necesario – Vea "Tensado de la cadena de sierra".
español / EE.UU Sistema de filtro de aire Tipo de cadena Paso Picco 3/8 pulg P Rapid 1/4 pulg Rapid 3/8 pulg; 0,325 pulg 0,404 pulg 2 3 3 001BA119 KN 1 Rapid : Invierta la barra – cada vez que afile la cadena y cada vez que sustituya la cadena, con ello evitará que se produzca desgaste por un solo lado, especialmente en la punta y la parte inferior de la barra. : Limpie regularmente el agujero de entrada de aceite (1), el conducto de aceite (2) y la ranura de la barra (3).
español / EE.UU Retiro del filtro de aire Limpieza del filtro estándar : Utilice la llave combinada para abrir los sujetadores (1) en el sentido de las flechas. Si se produce una pérdida notable de potencia del motor: : Quite la cubierta de la caja del carburador (2). Los filtros STIHL (estándar y HD) tienen una larga vida útil si se mantienen en condición seca. Siempre use filtros STIHL en condición seca.
español / EE.UU Limpieza del filtro HD 2 2 1 Si se produce una pérdida notable de potencia del motor: En caso de suciedad difícil o tela de filtro pegajosa: : : Limpie el prefiltro de fieltro (1). Después de limpiar el prefiltro varias veces: : Separe los componentes del filtro. : Golpee el filtro HD (2) en la palma de la mano o sóplelo con aire comprimido de adentro hacia afuera.
español / EE.UU Manejo del motor Ajuste del carburador Las emisiones de gases de escape son controladas por el diseño de parámetros y componentes fundamentales del motor (por ej. carburación, encendido, regulación y regulación de la válvula o lumbrera) sin la adición de ningún equipo importante. Información general Ajuste estándar El carburador se ajusta en la fábrica al ajuste estándar. Este ajuste provee una mezcla óptima de combustible y aire bajo la mayoría de las condiciones de funcionamiento.
español / EE.UU Ajuste de ralentí Funcionamiento irregular a ralentí, aceleración deficiente (aunque se ha abierto el tornillo de ajuste de baja velocidad 1/4 de vuelta) Ajuste fino para funcionamiento a alturas grandes Puede ser necesario efectuar un ajuste ligero si la potencia del motor no es adecuada para trabajar a grandes alturas: : Revise el ajuste estándar. : Caliente el motor. Gire el tornillo de ajuste de velocidad alta (H) en sentido horario (mezcla más pobre), pero no más allá del tope.
español / EE.UU : Si el motor pierde potencia, revise el chispero* en el silenciador. : Espere hasta que el silenciador se enfríe. : Saque el tornillo (1). : Quite el chispero (2). : Limpie el chispero. Si el chispero está dañado o con depósitos gruesos de carbón, instale uno nuevo. : Vuelva a instalar el chispero. : Coloque el tornillo y apriételo firmemente.
español / EE.UU Sustitución de la cuerda de arranque y resorte de rebobinado Saque los tornillos (1). : Empuje el protector de mano hacia arriba. : Aparte del cárter la parte inferior de la caja del ventilador y retírela hacia abajo. 000BA036 TR 1 MS 441 C : Quite el resto de la cuerda del rotor y del mango. : Pase la cuerda nueva por la parte superior del mango de arranque.
español / EE.UU 2 3 5 6 : Instale los trinquetes (4) en el rotor de la cuerda. : Instale la arandela (3) en el poste del arrancador. : Use un destornillador o alicates adecuados para instalar la pinza de resorte (2) en el poste del arrancador y sobre los vástagos de los trinquetes – la pinza de resorte debe apuntar en sentido horario como se muestra en la ilustración.
español / EE.UU Almacenamiento de la máquina Sustitución del resorte de rebobinado roto : Vacíe y limpie el tanque de combustible en una zona bien ventilada. : Deseche los residuos de combustible y solución de limpieza de acuerdo con los requerimientos locales de protección del medio ambiente. : Haga funcionar el motor hasta que el carburador se seque, esto ayuda a evitar que los diafragmas del carburador se peguen.
español / EE.UU Revisión y sustitución de la rueda dentada de cadena : : Quite la cubierta de la rueda dentada, la cadena y la barra guía. Instalación de la rueda con dientes rectos / rueda dentada tipo llanta 5 Suelte el freno de cadena: Tire del protector de la mano hacia el mango delantero. 6 : Limpie la caja de cojinetes de aguja y la punta del cigüeñal y lubrique con grasa STIHL ( “Accesorios especiales”). : Empuje la caja de cojinetes de aguja sobre el cigüeñal.
español / EE.UU Mantenimiento y afilado de la cadena de sierra Cadena debidamente afilada : Limpie la cadena. : Revise la cadena en busca de roturas en sus eslabones y daños en sus remaches. : Sustituya todas las piezas dañadas o desgastadas de la cadena e instale piezas nuevas que tengan la misma forma y tamaño que las originales. Es absolutamente esencial cumplir con los ángulos y dimensiones abajo especificados.
español / EE.UU 90° 85° 70° 60° 80° 30° 35° : Use un portalima Se debe usar un portalima (accesorio especial) para afilar manualmente la cadena (vea la tabla "Herramientas de afilado"). Los ángulos de rectificación correctos están marcados en el portalima. 120 0° 90° Utilice un calibrador de rectificación STIHL (accesorio especial – vea la tabla "Herramientas de afilado").
español / EE.UU La lima afila únicamente en la pasada de ida – quite la lima del cortador para la pasada de retorno. : Evite tocar las amarras y eslabones impulsores con la lima. : Gire la lima a intervalos regulares al limar para evitar desgastar uno de sus lados solamente. : Utilice un trozo de madera dura para quitar las rebabas del borde cortante. : Compruebe el ángulo con el calibrador de rectificación. El ajuste del calibrador de profundidad se reduce cuando se afila la cadena.
español / EE.UU : Las otras partes de la pletina de amarre de tres salientes y el eslabón impulsor con saliente no deben afilarse ya que eso podría aumentar la tendencia de la motosierra a dar contragolpes. 689BA052 KN 689BA044 KN RSC3, RMC3, PMC3: La parte superior del eslabón impulsor con saliente (con la marca de servicio) se baja junto con el calibrador de profundidad.
español / EE.
Entradas de enfriamiento Limpiar X Aletas del cilindro Limpiar X Canal de prefiltro y cuerpo del carburador Limpiar X Obturador, precalentador del carburador y canal de precalentamiento Limpiar (solamente durante invierno) X Carburador Comprobar el ajuste de ralentí – la cadena no debe girar X X X X Ajustar el ralentí X Ajustar la distancia entre electrodos Bujía Todos los tornillos y tuercas accesibles (no los tornillos de ajuste) 2) Chispero en silenciador* Cámara de combustión Gancho
español / EE.
español / EE.UU Definiciones 1 Bloqueo giratorio de la cubierta de la caja del carburador Traba la cubierta de la caja del carburador. 2. Tornillo de ajuste del carburador Para afinar el carburador. 3. Obturador Con posiciones para invierno y verano. El carburador se calienta en la posición de invierno. 4. Casquillo de la bujía Conecta la bujía al alambre de encendido. 5.
español / EE.UU Especificaciones EPA / CEPA: El período de cumplimiento de emisiones indicado en la etiqueta de cumplimiento de emisiones es la cantidad de horas de funcionamiento para la cual la máquina ha demostrado la conformidad con los requerimientos de emisiones del Gobierno federal de los EE.UU.
español / EE.UU Debido a la posibilidad de que nuevas combinaciones de barra/cadena hayan sido desarrolladas después de la publicación de este manual, consulte con su concesionario STIHL acerca de las recomendaciones más recientes de STIHL.
español / EE.UU Mantenimiento y reparaciones Los usuarios de esta máquina deben efectuar únicamente los trabajos de mantenimiento descritos en este manual. Solamente los talleres autorizados por STIHL deben llevar a cabo los demás trabajos de reparación. Los reclamos de garantía presentados después de realizadas las reparaciones serán aceptados únicamente si las mismas fueron ejecutadas por un concesionario de servicio autorizado STIHL utilizando piezas de repuesto originales de STIHL.
español / EE.UU No para California: Declaración de garantía de STIHL Incorporated sobre sistemas de control de emisiones según normas Federales Sus derechos y obligaciones de garantía La Agencia de Protección del Medio Ambiente (EPA) de los EE.UU. y STIHL Incorporated se complacen en explicarle la garantía del sistema de control de emisiones instalado en el motor de su equipo. En los EE.UU.
español / EE.UU subsiguiente que el motor está libre de defectos en el material y fabricación que puedan causar el incumplimiento de los reglamentos aplicables durante un período de dos años. Período de garantía El período de garantía comienza en la fecha en que el motor del equipo utilitario es entregado a usted y usted firma y remite la tarjeta de garantía a STIHL.
español / EE.
BA_U4_86_01.fm Seite 1 Mittwoch, 31. Mai 2006 2:49 14 ! WARNING! ! ADVERTENCIA! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. El gas de escape del motor de esta máquina contiene productos químicos que en el estado de California son considerados como causantes de cáncer, defectos de nacimiento u otros efectos nocivos para los órganos de la reproducción.