StorCase® Technology InfoStation® 14-Bay SCSI Ultra320 External Expansion Chassis Installation Guide
i StorCase® Technology InfoStation® 14-Bay SCSI Ultra320 External Expansion Chassis Installation Guide Part No. D89-0000-02230 B00 October 2003 StorCase Technology, Inc. 17600 Newhope Street Fountain Valley, CA 92708-9885 Phone (714) 438-1850 Fax (714) 438-1847 InfoStation 14-Bay U320 Installation Guide - Rev. B00 StorCase Technology, Inc.
ii Important Safety Instructions 1. Read all these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Do not use this product near water. 5. This product should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. 6.
iii Table of Contents INSTALLATION ...................................................................................................................... Installing the Drive(s) into the InfoStation ................................................................... Drive Preparation .................................................................................................. Carrier Preparation ...............................................................................................
iv NOTICE: This User's Guide is subject to periodic updates without notice. While reasonable efforts have been made to ensure accuracy of this document, StorCase Technology, Inc. assumes no liability resulting from errors or omissions in this publication, or from the use of the information contained herein. Please check the StorCase web site at http://www.storcase.com or contact your StorCase representative for the latest revision of this document. StorCase Technology, Inc.
Installation 1 INSTALLATION CAUTION: The InfoStation contains NO USER SERVICEABLE PARTS inside the unit. Warranty is VOID if any of the modules inside the InfoStation are opened. Refer ALL servicing to qualified service personnel! This unit has more than one power supply cord. Disconnect two power supply cords before servicing to avoid electric shock. Before removing any component from its packaging, discharge any static electricity by touching a properly grounded metal object.
2 Installation Inserting a Drive Carrier (without a Drive Installed) Lift carrier handle while inserting drive carrier into chassis. Push down on carrier handle once carrier is pushed all the way in. The carrier should latch into place if inserted correctly. Lock the key lock to prevent unauthorized removal or installation of drive carrier.
Installation 3 Installing a Drive into the Drive Carrier NOTES: A #2 Phillips screwdriver will be required for this procedure. 1. Install the drive(s) into the drive carrier(s). Drive(s) must be side-mounted into the drive carrier(s) using #6-32 Phillips Pan Hd. screws (Figure 3). 2. After the drive(s) have been installed in to the drive carrier(s), carefully insert the carrier(s) back into the chassis (refer to section "Inserting a Drive into the Chassis" for further information).
4 Installation Inserting a Drive into the Chassis NOTES: A new drive can be inserted into an empty bay at anytime. However, the drive will not be ready for access until the following procedure is followed. The key lock is only to prevent unauthorized removal or installation of the drive carrier. Locking the key lock is not required for drive carrier operation. 1. Simply insert the drive carrier into the empty bay. 2. Drive is ready to be accessed when the Drive Ready LED glows.
Installation 5 Removing/Installing the Power Supply Module WARNING: Handling certain plastic coated cords or cables associated with this product may expose you to lead, a chemical known to cause birth defects or other reproductive harm. Wash your hands after handling cable(s). CAUTION: The power supply module contains NO USER SERVICEABLE PARTS inside the unit. Warranty is VOID if module is opened. Refer ALL servicing to qualified service personnel! This unit has more than one power supply cord.
6 Installation Power Supply Module Release Lever Handle Figure 4: Removing/Installing the Power Supply Module StorCase Technology, Inc. InfoStation 14-Bay U320 Installation Guide - Rev.
Installation 7 Removing/Installing the Fan Module CAUTION: The fan module contains NO USER SERVICEABLE PARTS inside the unit. Warranty is VOID if module is opened. Refer ALL servicing to qualified service personnel! This unit has more than one power supply cord. Disconnect two power supply cords before servicing to avoid electric shock. NOTES: The fan module is hot-swappable. The chassis may remain on when removing and installing the module.
8 Installation Removing/Installing the I/O Module CAUTION: Remove ALL power from the InfoStation before removing the I/O module. The I/O module contains NO USER SERVICEABLE PARTS inside the unit. Refer ALL servicing to qualified service personnel! NOTES: The I/O module is NOT hot-swappable! Remove ALL power to chassis before removing and installing the I/O module. Blank plate (provided) must be installed if module slot is left empty.
Installation 9 Removing the Option Cover Plate NOTES: A #2 Phillips screwdriver will be required for this procedure. Blank plate (provided) must be installed if module slot is left empty. Installation of the blank plate is necessary for proper cooling inside chassis. 1. Remove the Phillips F. H. screw securing the cover plate to the InfoStation chassis (Figure 7). 4. Remove the cover plate (Figure 7). 5. To reinstall cover plate, simply reverse the above mentioned steps.
