Installation Guide

ManualsBrandsStyle Selections ManualsBathroom & Wall Lighting3-Light Black Transitional Vanity Light Fitter

Français p. 9

Español p. 17

ATTACH YOUR RECEIPT HERE

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Sunday.

SM20243

STYLE SELECTIONS and logo design are trademarks

APPROVED FOR USE

IN DAMP LOCATIONS

VANITY BAR FITTER

ITEM #2528588, 2528587

2528591, 2528590

MODEL #VB120-2CH, VB120-3CH

VB120-3BK, VB120-4BK

MODEL #VB120-2CH

MODEL #VB120-3CH

VB120-3BK

MODEL #VB120-4BK

Summary of content (8 pages)

PAGE 1
ITEM #2528588, 2528587 2528591, 2528590 VANITY BAR FITTER MODEL #VB120-2CH, VB120-3CH VB120-3BK, VB120-4BK STYLE SELECTIONS and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved. Français p. 9 Español p.
PAGE 2
TABLE OF CONTENTS Package Contents ................................................................................................................ 2 Hardware Contents ........................................................................................................................... 3 Safety Information ................................................................................................................ 3 Preparation ........................................................................
PAGE 3
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal.
PAGE 4
SAFETY INFORMATION • DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting strap that is first attached to the outlet box. Wire connectors will not support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or fire.
PAGE 5
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. 1 DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. 2. Remove existing fixture and disconnect all electrical wiring. ON ON OFF OFF 2 3. Remove mounting plate (B) from fixture (A) by removing mounting plate screws (C) from the edges of the fixture (A). Save mounting plate screws (C) for later use.
PAGE 6
ASSEMBLY INSTRUCTIONS 4. Attach mounting plate (B) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. Tighten machine screws (BB) to secure mounting plate (B). 4 B BB CAUTION: The fixture must be mounted to an outlet box that is supported by the building structure.
PAGE 7
ASSEMBLY INSTRUCTIONS 6. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. Push wire connectors (AA) gently back into outlet box. Carefully push excess wiring into outlet box. 6 AA AA A WARNING: Make sure no bare wire or wire strands are visible after making connections. AA 7. Attach fixture (A) to mounting plate (B) using the mounting plate screws (C) previously removed (Step 3, Page 5).
PAGE 8
ASSEMBLY INSTRUCTIONS 9. Install standard-base bulbs (not included). Use 60-watt max. incandescent bulbs or CFL/LED equivalent. 9 A WARNING: When replacing bulb(s), please allow bulbs and fixture to cool down before touching. Restore power and test fixture (A). If lights do not function, please refer to TROUBLESHOOTING below. Bulb CARE AND MAINTENANCE • Shut off main power supply. Wipe with soft cloth or use window cleaner. Do not use an abrasive cleaner.