INTERNATIONAL DESIGN GUIDE
Contents Built-In Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PRO 48 Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . 34 Integrated Refrigeration . . . . . . . . . . . . . . . . . . . . . . 39 Wine Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information.
Built-In Refrigeration 3 subzero.com/specs Built-In Refrigeration. For the built-in line, Sub-Zero designers and engineers took a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges. Inside, new technology in food preservation makes the built-in line nothing short of revolutionary.
Built-In Refrigeration 4 Built-In Models All Refrigerator / All Freezer Models SPECIFICATIONS OVERALL DIMENSIONS Interior Capacity R (L) F (L) 914 mm 610 mm ALL REFRIGERATOR / ALL FREEZER MODELS ICBBI-36R ICBBI-36F 662 640 OVER-AND-UNDER MODELS ICBBI-30U ICBBI-36U 362 451 116 149 346 455 453 533 531 227 227 230 270 274 SIDE-BY-SIDE MODELS ICBBI-36S ICBBI-42S ICBBI-42SD ICBBI-48S ICBBI-48SD Shipping Weight 2134 mm 1873 mm kg ALL REFRIGERATOR / ALL FREEZER MODELS ICBBI-36R ICBBI-36F
Built-In Refrigeration 5 subzero.
Built-In Refrigeration 6 Side-by-Side Models OVERALL DIMENSIONS 914 mm 610 mm 1067 mm 610 mm 2134 mm 2134 mm 1873 mm HEIGHT DIMENSIONS ± 13 mm 1873 mm 102 mm HEIGHT DIMENSIONS ± 13 606 mm mm 102 mm 606 mm 216 mm 260 mm 606 mm 222 mm 318 mm 565 mm 668 mm 60 mm 60 mm MODEL ICBBI-36S Overall dimensions are based on stainless steel models. For flush inset applications, add 13 mm to door clearance dimensions.
Built-In Refrigeration 7 subzero.
Built-In Refrigeration 8 Built-In Models STANDARD INSTALLATION TOP VIEW 610 mm OPENING DEPTH 610 mm 2127 mm A OPENING DEPTH OPENING HEIGHT OPENING WIDTH SIDE VIEW FRONT VIEW ICBBI-36R and ICBBI-36F 902 mm IMPORTANT NOTE: If two units are installed side by side, refer to pages 21–22 for dual standard installations. ICBBI-30U 746 mm Stainless steel models are ready to install out of the box.
Built-In Refrigeration 9 subzero.com/specs Planning Information ELECTRICAL REQUIREMENTS PLUMBING REQUIREMENTS International models from the factory designed without a transformer require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device.
Built-In Refrigeration 10 Overlay Panels If you and your client have ordered an overlay model, you will be adding panels and handles to give the unit a more custom look. The overlay panel design option is available for all built-in overlay models. For exact door panel dimensions, refer to overlay panel specifications on the following pages. IMPORTANT NOTE: Overlay models can be used in an overlay or a flush inset application.
Built-In Refrigeration 11 subzero.
Built-In Refrigeration 12 Overlay Panels H H H H A B W W W ICBBI-36S / ICBBI-42S / ICBBI-48S W ICBBI-48SD Model ICBBI-36S REFRIGERATOR Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel Models ICBBI-48S and ICBBI-48SD W H 510 mm 487 mm 503 mm 1772 mm 1751 mm 1767 mm W H 398 mm 376 mm 392 mm 1772 mm 1751 mm 1767 mm W H 914 mm 892 mm 908 mm 235 mm* 211 mm 227 mm REFRIGERATOR Overlay Panel Spacer P
Built-In Refrigeration 13 subzero.com/specs Flush Inset Application It is necessary to consider the following points when planning for a flush inset application: • The flush inset depth is 56 mm deeper than the standard opening. • The flush inset width is 64 mm wider than the standard opening. • The flush inset height is 6 mm higher than the standard opening.
Built-In Refrigeration 14 Built-In Models FLUSH INSET INSTALLATION TOP VIEW 665 610 mm 665 mm mm DEPTH FLUSH TO CLEAT INSET DEPTH 32 mm UNIT WITH 19 mm PANEL 610 mm OPENING FLUSH DEPTH INSET TO CLEAT DEPTH CLEAT TOP VIEW CLEAT 76 mm typical DETAIL A 56 mm 56 mm 6 mm 32 mm CLEAT Detail A 610 mm DEPTH TO CLEAT 56 mm 665 mm FLUSH INSET DEPTH 76 mm typical CLEAT 102 mm 2127 mm HEIGHT TO CLEAT A 32 mm 32 mm WIDTH TO CLEAT B 2134 mm SHADED AREA MUST BE FINISHED 610 mm OPENING DEPT
Built-In Refrigeration 15 subzero.com/specs Flush Inset Panels The flush inset application allows decorative panels on the front of the unit to be flush with surrounding cabinetry and is available for all built-in overlay models. For exact panel dimensions, refer to flush inset panel specifications on the following pages. The flush inset design allows decorative panels to cover the door trim for a seamless appearance that blends with the design of the room.
Built-In Refrigeration 16 Flush Inset Panels PANEL OFFSETS TOP VIEW TOP VIEW Illustrations A–F provide panel offsets and reveals for all built-in models in a flush inset application. Refer to the chart below for reference to the illustrations relating to your specific model. For additional information on model-specific panel reveals, visit the specification library section of our website, subzerotrade.com.
Built-In Refrigeration 17 subzero.
Built-In Refrigeration 18 Flush Inset Panels H H H H A B W W W ICBBI-36S / ICBBI-42S / ICBBI-48S W ICBBI-48SD Model ICBBI-36S REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel Models ICBBI-48S and ICBBI-48SD W H 522 mm 487 mm 503 mm 1772 mm 1751 mm 1767 mm W H 411 mm 376 mm 392 mm 1772 mm 1751 mm 1767 mm W H 940 mm 892 mm 908 mm 235 mm 211 mm 227 mm REFRIGERATOR Flush I
Built-In Refrigeration 19 subzero.com/specs Dispenser MODEL ICBBI-48SD The refrigerator door panel must include a cut-out to accommodate the dispenser glasswell and bezel. The thickness of the panel in this area can range from 6 mm to a maximum of 29 mm. IMPORTANT NOTE: Regardless of the thickness of the panel for model ICBBI-48SD, you must plan for a flat landing area for the decorative bezel surrounding the glasswell area. The illustration to the right provides exact bezel dimensions.
Built-In Refrigeration 20 Side Panels Side panels can be used with every design application. When planning for side panels with the installation of a built-in model, you need to be aware of the space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your unit, the height of the panel may vary. IMPORTANT NOTE: The use of side panels may change the width of your rough opening. The side panel will need to be a minimum of 610 mm deep and 13 mm thick.
Built-In Refrigeration 21 subzero.com/specs Dual Installation STANDARD APPLICATION Dual Installation Panel Requirements Two overlay or stainless steel units may be placed side by side in a dual installation. Some standard applications will require a dual installation kit, available through your authorized Sub-Zero dealer. If you are installing two units side by side in a flush inset application, refer to page 23.
Built-In Refrigeration 22 Dual Installation STANDARD INSTALLATION TOP VIEW 610 mm OPENING DEPTH TWO UNITS WITH 19 mm PANEL 610 mm 2127 mm A OPENING DEPTH OPENING HEIGHT OPENING WIDTH SIDE VIEW FRONT VIEW Two 762 mm Models 1518 mm IMPORTANT NOTE: A dual installation kit will be required for this installation. 762 mm and 914 mm Models 1670 mm Stainless steel models are ready to install out of the box.
Built-In Refrigeration 23 subzero.com/specs Dual Installation FLUSH INSET APPLICATION Dual Installation Panel Requirements Installing two built-in models side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets. It will also require a dual installation kit, available through your authorized Sub-Zero dealer.
Built-In Refrigeration 24 Dual Installation FLUSH INSET INSTALLATION TOP VIEW 665 mm 610 mm DEPTH FLUSH TO CLEAT INSET DEPTH 665 mm 32 mm TWO UNITS WITH 19 mm PANEL 610 mm OPENING FLUSH DEPTH INSET TO CLEAT DEPTH CLEAT TOP VIEW CLEAT 76 mm typical DETAIL A 56 mm 56 mm 6 mm 32 mm CLEAT 610 mm Detail A DEPTH TO CLEAT 56 mm 665 mm FLUSH INSET DEPTH 76 mm typical CLEAT 2127 mm HEIGHT TO CLEAT 102 mm A 32 mm 32 mm WIDTH TO CLEAT 610 mm B 2134 mm SHADED AREA MUST BE FINISHED OPEN
Built-In Refrigeration 25 subzero.com/specs Dual Installation FLUSH INSET PANEL OFFSETS TOP VIEW TOP VIEW When installing two built-in models side by side in a flush inset application, you must decrease the width of the decorative flush inset panels by 13 mm. Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing.
Built-In Refrigeration 26 Dual Installation—Flush Inset Panels H H H W ICBBI-30U / ICBBI-36U ICBBI-30U REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel ICBBI-36U W H 775 mm 740 mm 756 mm 1273 mm 1253 mm 1268 mm W H 775 mm 740 mm 756 mm 483 mm 459 mm 475 mm W H 775 mm 740 mm 756 mm 235 mm 211 mm 227 mm REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel W H 927 mm 892
Built-In Refrigeration 27 subzero.com/specs Dual Installation Kit INSTALLATION WITH DUAL WIDE GRILLE INSTALLATION WITH INDIVIDUAL GRILLES This kit will replace the existing grilles that ship with the units and span the entire width of both units. The kit includes a 6 mm center trim strip (required for proper installation of the dual wide grille), heater, dual kickplate and mounting hardware. Dual wide grilles are available for all built-in models and design applications.
Built-In Refrigeration 28 Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. • Flush inset front panels in stainless steel with handle options. STANDARD HANDLES Refer to the chart below for standard handle lengths and the stud spacing of tubular and pro handles used on built-in models.
Built-In Refrigeration 29 subzero.com/specs Overlay Panel Thickness FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 16 mm thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door.
Built-In Refrigeration 30 Overlay Application FULL-SCALE TEMPLATE 606 mm OVERALL WIDTH OF UNIT TO REAR OF UNIT 0 mm 6 mm 13 mm 19 mm 25 mm 32 mm 38 mm 44 mm 51 mm 57 mm 63 mm 70 mm 76 mm 83 mm 89 mm 25 mm THICK PANEL 19 mm THICK OVERLAY PANEL (TYPICAL) 6 mm BACKER PANEL 0 mm 25 mm DOOR OPENING 90° TOP VIEW SCALE
Built-In Refrigeration 31 subzero.com/specs Flush Inset Application 610 mm FULL-SCALE TEMPLATE TO BACK WALL For panels thicker than 19 mm, a 90° door stop may be required to prevent interference with adjacent cabinets.
Built-In Refrigeration 32 FILLER STRIP 32 mm APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE DOOR OPEN 110° Dual Installation—Standard FULL-SCALE TEMPLATE Typical overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Depending on panel thickness, a 90° door stop may be required.
Built-In Refrigeration 33 subzero.com/specs FILLER STRIP 38 mm 13 mm PROFILE OF 19 mm FLUSH INSET PANEL AND TUBULAR HANDLE Dual Installation—Flush Inset FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maximum 110° door opening. Depending on panel thickness, a 90° door stop may be required.
PRO 48 Refrigeration PRO 48 Refrigeration. Freshness finds unmistakable expression in the Sub-Zero PRO 48. A 363 kg monument to food preservation—equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding.
PRO 48 Refrigeration 35 subzero.
PRO 48 Refrigeration 36 PRO 48 Models STANDARD AND FLUSH BUILT-IN INSTALLATIONS TOP VIEW OPENING DEPTH OPENING DEPTH OPENING WIDTH OPENING HEIGHT SIDE VIEW Opening Dimensions FRONT VIEW Standard Flush Opening Width 1206 mm 1219 mm Opening Height 2127 mm 2137 mm Opening Depth 610 mm 660 mm IMPORTANT NOTE: For standard built-in installations, the face frame of the unit will extend 51 mm beyond cabinetry.
PRO 48 Refrigeration 37 subzero.com/specs Planning Information PRO 48 models can be used freestanding or installed as a standard or flush built-in application. For standard built-in installations, the face frame of the unit will extend 51 mm beyond cabinetry. In flush built-in installations, the front of the face frame will be flush with surrounding cabinetry.
PRO 48 Refrigeration Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. • Freestanding kit, which contains two stainless steel side panels and top lid. • Stainless steel side panel. • Refrigerator drawer dividers for compartmentalized storage. • Stainless steel slide-out refrigerator bin. • Dozen egg container. • 90° door stop.
Integrated Refrigeration 39 subzero.com/specs Integrated Refrigeration. With custom cabinet fronts and hardware, Sub-Zero invented integrated drawers and tall units that disappear into the decor. Integrated units fit flush with other cabinets, making integrated refrigeration as practical and beautiful in the master suite, bar or theatre room as in the kitchen. INTEGRATED MODELS KEY FEATURES 686 mm • Custom cabinet fronts and hardware allow for infinite design options.
Integrated Refrigeration 40 Overall Dimensions 686 mm TALL MODELS 914 mm TALL MODELS 686 mm 610 mm 914 mm 610 mm 356 mm 356 mm 33 mm 21 mm 1976 mm 1995 mm 2032 mm 2032 mm TO TOP OF OPENNG 10 mm 13 mm 13 mm 337 mm 876 mm 260 mm TO TOP OF OPENNG 10 mm 337 mm 876 mm 260 mm 518 mm 518 mm 248 mm 248 mm HEIGHT DIMENSIONS ± 13 102 mm mm HEIGHT DIMENSIONS ± 13 610 mm 610 mm 178 mm 117 mm 495 mm 102 mm mm 648 mm 495 mm DIMENSIONS WILL VARY WITH PANEL THICKNESS MODELS ICB700
Integrated Refrigeration 41 subzero.
Integrated Refrigeration 42 Opening Dimensions INTEGRATED MODELS IMPORTANT NOTE: The depth of each integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 635 mm.
Integrated Refrigeration 43 subzero.com/specs Electrical Requirements International models from the factory designed without a transformer require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device. The electrical supply should be located within the shaded area shown in the illustrations. Follow local codes and ordinances when installing the receptacle.
Integrated Refrigeration 44 Plumbing Requirements For integrated models with an automatic ice maker, the water supply line should be located through the floor or back wall, within the shaded area shown in the illustrations. The water supply line should be connected to the house supply with an easily accessible shut-off valve between the supply and the unit. Do not use self-piercing valves. A saddle valve kit (4200880) is available through your authorized Sub-Zero dealer.
Integrated Refrigeration 45 subzero.com/specs Cabinetry Applications FRAMELESS CABINETRY 679 mm 908 mm PANEL WIDTH PANEL WIDTH A A 1153 mm 1153 mm 2029 mm 2029 mm A A 345 mm 345 mm A A 876 mm 424 mm 424 mm 102 mm 4" (102) 686 mm 914 mm FINISHED OPENING FINISHED OPENING ALL REVEALS (A) ARE 3 mm.
Integrated Refrigeration 46 Cabinetry Applications DOOR PANEL HEIGHT TOE KICK CLEARANCE The height of the door panel can extend beyond the typical panel height, provided you do not exceed the panel weight limit. The illustration below shows how the panel may be extended and what you need to consider to finish the area behind the door panel. The toe kick clearance can vary with the height of the panel. You must keep a minimum space of 102 mm clear below the bottom edge of the panel for proper venting.
Integrated Refrigeration 47 subzero.com/specs Cabinetry Applications Integrated refrigeration is compatible with virtually any style and look of cabinetry. These models can be used with framed as well as frameless cabinetry. Because of the precise application and the look you may want to achieve, keep the following considerations in mind: The thickness of the front panels can vary. A minimum 16 mm thick panel is required, but the thickness can be increased provided the panel weight limit is not exceeded.
Integrated Refrigeration 48 Cabinetry Applications Dual Installations The illustrations below show typical applications of framed and frameless cabinetry. Refer to the full-scale templates at the end of this section for specifics on door openings. Two integrated units may be placed side by side in a dual installation. Depending on the models specified, opening widths will be 1372 mm, 1600 mm or 1829 mm. Panel width dimensions will vary slightly from single installations.
Integrated Refrigeration 49 subzero.com/specs Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. STANDARD HANDLES Refer to the chart below for standard handle lengths and the stud spacing of tubular and pro handles used on integrated models. • Stainless steel front panels with handles.
Integrated Refrigeration 50 INTEGRATED DOOR MAXIMUM 105° OPENING Maximum Door Opening FULL-SCALE TEMPLATE If the panel is thicker than 19 mm, use the built-in 90° door stop to prevent damage to the panel and face frame at the maximum door opening.
Wine Storage 51 subzero.com/specs Wine Storage. Wine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced shelves, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home.
Wine Storage 52 Overall Dimensions UNDERCOUNTER WINE STORAGE 606 mm 610 mm 864 mm 102 mm 645 mm 60 mm MODEL ICB424G Overall dimensions are based on stainless steel panels and handles.
Wine Storage 53 subzero.
Wine Storage 54 Overall Dimensions Capacity and Weight FULL-SIZE WINE STORAGE Storage Capacity 762 mm 610 mm 2134 mm 1873 mm HEIGHT DIMENSIONS ± 13 mm 102 mm 606 mm 606 mm 432 mm 796 mm 60 mm MODEL ICBWS-30 Overall dimensions are based on the stainless steel model. For flush inset applications, add 13 mm to door clearance dimensions.
Wine Storage 55 subzero.com/specs Opening Dimensions UNDERCOUNTER WINE STORAGE FULL-SIZE WINE STORAGE TOP VIEW 610 mm 635 mm OPENING DEPTH OPENING DEPTH 610 mm 876 mm 610 mm OPENING DEPTH OPENING HEIGHT OPENING WIDTH SIDE VIEW TOP VIEW 635 mm 2032 mm 686 mm OPENING DEPTH OPENING HEIGHT OPENING WIDTH FRONT VIEW MODEL ICB424G SIDE VIEW FRONT VIEW MODELS ICB427G AND ICB427RG IMPORTANT NOTE: The depth of each integrated model is 610 mm from the front of the unit to its back.
Wine Storage 56 Opening Dimensions Planning Information FULL-SIZE WINE STORAGE All wine storage models must be installed so that the door can open a minimum of 90° or you will have problems pulling the wine shelves out. For corner installations, you need to allow for a minimum 76 mm filler so the door can open to 90°. If you are using larger-handle hardware, you will also need to take that into account. Refer to door clearance specifications.
Wine Storage 57 subzero.com/specs Planning Information DUAL INSTALLATIONS Electrical Requirements If you are installing a wine storage unit next to an existing Sub-Zero unit, you may have to allow for a filler strip. Power Supply If you are installing a model ICB427G or ICB427RG next to an existing integrated unit, with 51 mm or less between the units, an optional heater kit will need to be installed to prevent moisture from forming between the units.
Wine Storage 58 Door Panels Overlay Panels Unless you are installing a stainless steel model, you will need to provide a frame for the glass door. If you order a stainless steel unit, models ICB424G, ICB424FSG and ICBWS-30 will be shipped with their panels and hardware installed. For models ICB427G and ICB427RG, optional stainless steel panels or custom panels will need to be installed. MODEL ICB424G The glass door is designed to be exposed to room air circulation.
Wine Storage 59 subzero.com/specs Integrated Panels MODELS ICB427G AND ICB427RG The integrated full panels or frame panels for glass doors for these models will follow some of the identical planning processes used with the integrated line. The installation of the door panels is completely different, however. Rather than using the mounting hardware we used with the integrated line, door panels for both models ICB427G and ICB427RG will be applied with screws applied through our door.
Wine Storage 60 Model ICBWS-30 OVERLAY PANEL OVERLAY PANEL SPECIFICATIONS Overlay model ICBWS-30 can be used in an overlay or flush inset application. The specific application will affect panel sizes, opening dimensions and the installation. H A A A Overlay model ICBWS-30 will be shipped without handle hardware and with an overlay panel grille as standard equipment. Along with the door panel, you will need to provide a panel for the grille and hardware to complement your surrounding cabinetry.
Wine Storage 61 subzero.com/specs Model ICBWS-30 FLUSH INSET PANEL FLUSH INSET PANEL SPECIFICATIONS Overlay model ICBWS-30 used in a flush inset application allows the decorative panel to cover the door trim for a seamless appearance. The most common way to achieve this look is to work with three panels—the decorative flush inset panel, which is typically 19 mm, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions.
Wine Storage 62 Model ICBWS-30 FLUSH INSET PANEL DUAL INSTALLATIONS Illustrations A–D provide panel offsets and reveals for model ICBWS-30 in a flush inset application. Refer to the chart below for reference to the illustrations. When two models ICBWS-30 or a model ICBWS-30 and built-in unit are installed side by side, a dual installation kit may be required. Contact your Sub-Zero dealer for the proper components and installation instructions.
Wine Storage 63 subzero.com/specs Model ICBWS-30 DUAL FLUSH INSET INSTALLATIONS DUAL FLUSH INSET PANEL SPECIFICATIONS Installing two models ICBWS-30 or a model ICBWS-30 and built-in unit side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets. It will also require a dual installation kit, available through your Sub-Zero dealer.
Wine Storage 64 Model ICBWS-30 DUAL FLUSH INSET PANELS TOP VIEW TOP VIEW When installing two models ICBWS-30 or a model ICBWS-30 and built-in unit side by side in a flush inset application, you must decrease the width of the decorative flush inset panels by 13 mm. Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing.
Wine Storage 65 subzero.com/specs Side Panels Handle Hardware MODEL ICBWS-30 For overlay and integrated models, handle hardware must be provided. Optional stainless steel tubular and pro handles are available through your authorized Sub-Zero dealer. When planning for side panels with the installation of the model ICBWS-30, you need to be aware of the space configuration to achieve a pleasing fit. Depending on the exact panel you are using, the height of the panel may vary.
Wine Storage 66 Accessories Door Frame Profile These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. FULL-SCALE TEMPLATE The full-scale template below shows an example of the door frame profile for wine storage models and the relationship to the overlay panel (rails and stiles). • Front panels in stainless steel with handle options.
Wine Storage 67 subzero.com/specs Wine Shelf Wood Facing FULL-SCALE TEMPLATE Dimension For each model, the wine storage shelves have a natural cherrywood facing. You can replace these strips with wood more complementary to your design and surrounding cabinetry. Refer to the full-scale template below. ICB424G and ICB424FSG ICB427G and ICB427RG ICBWS-30 A To remove the cherry strips, take the shelves out and remove the screws. Reverse the procedure to affix the new wood facing.
Wine Storage 68 Door Clearance FULL-SCALE TEMPLATE Model ICB424G should extend a minimum of 6 mm beyond the front surface of adjoining cabinetry to allow for the maximum 145° door opening. The unit can be installed flush with adjacent cabinetry, however, there is potential for interference with the panel if the door is opened past 90°.
SUB-ZERO, INC. P O BOX 44848 MADISON, WI 53744 USA SUBZERO.
