OPERATION & MAINTENANCE MANUAL ST45, ST55, ST75 U.S.A. & Mexico PART NUMBER: 88292021-240 R01 SAFETY WARNING Users are required to read the entire User Manual before handling or using the product. Keep the User Manual in a safe place for future reference. WARRANTY NOTICE Failure to follow the instructions and procedures in this manual, or misuse of this equipment, will void its warranty.
Service Training Courses Sullair training courses provide hands-on and classroom instruction for the proper operation, maintenance, and servicing of Sullair products. Individual courses on Stationary compressors, variable speed drives, compressor electrical systems, and dryers are offered at regular intervals throughout the year at Sullair’s training facility located in Michigan City, Indiana.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Table of Contents Table of Contents Section 1: Safety.......................................................................................................7 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 General............................................................................................................................................ 7 Personal protective equipment ........................................
Table of Contents ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 2.5.2 Ambient temperature .......................................................................................................... 19 2.5.2.1 High ambient temperature and overheating .............................................................. 19 2.6 Fluid/air separation system ........................................................................................................... 19 2.6.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 5.7 5.8 5.9 Table of Contents Motor overload protection.............................................................................................................. 30 Phase failure/reversal.................................................................................................................... 31 Run-on timer................................................................................................................
Table of Contents 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Motor and air end system.............................................................................................................. 46 Air inlet system .............................................................................................................................. 50 Fluid piping system......................................................................
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 1: Safety Section 1 Safety most compressors and the concepts behind these statements are generally applicable to all compressors. NOTE 1.2 Personal protective equipment Operator is required to read entire instruction manual. 1.1 General Sullair and its subsidiaries design and manufacture all of their products so they can be operated safely.
1: Safety ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual material. Any acoustical material with a protective covering that has been torn or punctured should be replaced immediately to prevent accumulation of liquids or fluid film within the material. DO NOT use flammable solvents for cleaning purposes. accordance with their manufacturer's recommendations. E. DO NOT use air tools that are rated below the maximum rating of the compressor.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual E. Make sure all personnel are out of and/or clear of the compressor prior to attempting to start or operate it. F. Disconnect and lock out all power at source and verify at the compressor that all circuits are de-energized to minimize the possibility of accidental startup, or operation, prior to attempting repairs or adjustments. This is especially important when compressors are remotely controlled. G.
1: Safety ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual ments or repairs to exposed live parts of the electrical system. Make all such adjustments or repairs with one hand only, so as to minimize the possibility of creating a current path through the heart. C. Attempt repairs in clean, dry and well lighted and ventilated areas only. D. DO NOT leave the compressor unattended with open electrical enclosures.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 1.11 Implementation of lockout/tagout The energy control procedure defines actions necessary to lockout a power source of any machine to be repaired, serviced or set-up, where unexpected motion, or an electrical or other energy source, would cause personal injury or equipment damage.
1: Safety ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 1.12 Safety warnings The following special instructions apply to VSD packages provided with electronic adjustable speed motor drives. These cautions that apply to VSD operation. WARNING Ground the unit following the instructions in this manual. Ungrounded units may cause electric shock and/or fire.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual NOTE CAUTION Install the variable speed drive in a well ventilated room that is not subject to temperature extremes, high humidity, or condensation, and avoid locations that are directly exposed to sunlight, or have high concentrations of dust, corrosive gas, explosive gas, inflammable gas, grinding fluid mist, etc. Improper installation may result in a fire hazard.
1: Safety ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 14 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 2: Description Section 2 Description 2.1 The air compression cycle The ShopTek™ air compressor uses a lubricated rotary screw air end and supporting components to create compressed air. When the rotors inside the air end turn, they draw outside air into the compressor through the air inlet system.
2: Description ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 1. Enclosure 5. Air inlet system 2. Electric control system 6. Motor & air end 3. Cooling fan system 7. Fluid/air separation system 4. Discharge system 8. Fluid piping system Figure 2-1: ST45, ST55 & ST75 machine layout 16 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 2.2 Air inlet system The air inlet system provides air for the compressor to pressurize. The primary components of the air inlet system are the air filter, inlet valve, and compressor air end. 2.2.1 General operation of the air inlet system The air end draws outside air through the air filter and inlet valve into the air end compression chamber.
2: Description ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual ommends installing a wet air receiver after the service connector. Additional information • For the size of the service connector, see Section 3.1: Machine specifications on page 21. 2.3.2 When pressure in the fluid/air separator is above 340 kPa (49.3 psi) and higher than the downstream pipeline pressure, the minimum pressure valve will be opened.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 2.5.2 Additional information • • For the viscosity required for the compressor fluid to act as a sealant, see Section 3.2: Lubricant specifications on page 21. 2.4.3 Fluid filter The fluid filter collects any impurities in the compressor fluid and ensures that only clean fluid enters the air end compression chamber and internal lubrication feeds.
2: Description ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual After hitting the wall of the separator tank, the compressed air/fluid mixture then flows through the separator element. The separator element removes fine fluid particles. These particles accumulate at the bottom of the element and return to the air end through the purge oil return line. 2.6.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 3: Specifications Section 3 Specifications 3.1 Machine specifications Table 3-1: Compressor specifications Model ST45 9 bar ST55 9 bar ST75 9 bar 9 bar (125 psi) 9 bar (125 psi) 9 bar (125 psi) Maximum working pressure 9.3 bar (135 psi) 9.3 bar (135 psi) 9.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292020-840 R02 3: Specifications 22 3.
Key Description 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
3: Specifications ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 24 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 4: Installation Section 4 Installation WARNING Incorrect installation or setup may void warranty. 4.1 Compressor pre-installation Before installing your ShopTek™ compressor, check it carefully for any transportation damage. If you find any damage, contact your Sullair representative immediately. 4.2.
4: Installation 4.3.2 ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Heat rejection and ventilation requirements 4.4 Connection to the air system The compressor rejects a considerable amount of heat, so you must install it in a well-ventilated area. Sullair recommends installing an isolation gate valve immediately after the service connector to make installation, service, and removal of the compressor easier.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 4: Installation 4.5.2.1 Checking the air end of a new machine 4.6.2 Rotate the flexible drive coupling by hand through two complete revolutions in the direction indicated by the arrows located on the air end and motor. For the motor to rotate in the correct direction, the power supply must be correctly connected. 4.5.3 • If the fluid level is below the minimum fluid level, see Section 6.4.1: Adding compressor fluid on page 35.
4: Installation ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 28 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 5: Operation Section 5 Operation 5.1 Compressor protection features Your ShopTek™ compressor controller optimizes the performance of your system by adding additional electronic protection to the motor and air end. 5.1.1 3. Perform all mechanical checks described in Section 4.5. 4. Open the isolation gate valve if it is installed.
5: Operation ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 5.3 Starting the compressor 5.5 Electronic controller If the compressor has been out of service for more than 60 days or you have installed the compressor in a new location, follow the steps under Section 5.2: Starting the compressor for the first time instead of this procedure. The EC2000 Controller Operation Manual describes the layout and explains the features of the ShopTek™ electronic controller. 1.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual pressor from restarting. The fault mode may be cleared by pressing the Reset button on the controller. CAUTION In the event of a motor overload protection shutdown fault, do not attempt to restart the compressor without first finding and correcting the underlying cause that triggered the motor overload protection.
5: Operation ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 32 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 6: Maintenance Section 6 Maintenance 6.1 General 6.2.1 Before starting the compressor • Check the compressor fluid level and add fluid if necessary. Normal operation of your compressor depends upon performing maintenance and service correctly and according to a consistent schedule. To help you follow this schedule, the ShopTek™ microprocessor controller has a programmable service timer.
6: Maintenance ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual • Tighten all electrical connections. • Assess the condition of the air filter element. If it is excessively dirty, you may need to replace it more frequently than the normal schedule (every 2000 hours). 6.3.2 Service every 1000 operating hours • Replace the fluid filter element(s). • Inspect the air filter element and replace it if necessary.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 6: Maintenance 6.4 Compressor maintenance Refer to Section 7: Parts List for the part numbers of all items mentioned in this section. WARNING Do not attempt any maintenance when the compressor is running or pressurized. Stop the compressor, relieve all internal pressure, and isolate the power supply before performing maintenance.
6: Maintenance ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Clean the lubrication system before changing fluid. If the ambient temperature is outside of the allowed range for the fluid, please contact your Sullair representative. WARRANTY INFORMATION Mixing of fluids other than Sullube® will void the compressor’s warranty. 1. Shut down the compressor, bleed pressure to zero, and allow the compressor to cool. 2.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 6: Maintenance • If the filter element is excessively dirty, replace it with a new element. • Do not strike the filter element against a hard surface to remove the dirt. You may damage the element. • Do not oil the filter element. 6.4.5 Purge oil return line filter maintenance Clean the purge oil return line filter after the first 50 hours of service.
6: Maintenance ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 9. Evenly tighten the separator cover bolts to 138 N m (102 lbf ft). 10. Check the continuity of the separator element to the ground. 11. Re-tension the separator cover bolts after the compressor has reached operating temperature. 6.4.7 Minimum pressure valve maintenance 1. Primary fluid/air separator element1 2.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 6: Maintenance 2. Disconnect the pipe connected to the minimum pressure valve and remove the valve from the cover of the fluid/air separator. 3. Unscrew the top cap of the valve and remove the piston from the valve. 4. Clean the valve and piston carefully. 5. Replace the O-ring, applying a layer of grease to the O-ring and the piston. 6. Apply Loctite gasket maker to the top cap of the valve and reassemble the valve. 7.
6: Maintenance ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual • A current detection device in the electrical cabinet of the compressor provides motor overload protection. • The motor should not make intermittent or unusual noises or vibrations when running (either at no load or load). 6.5.2 Main motor maintenance and repair • The operating environment should be dry, the motor surface should be clean, and the motor’s air inlet should not be blocked by dust or fibers.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 6.5.4.2 Brush and vacuum You can clean easy-to-reach surfaces that are dirty or very dusty by scrubbing them with a short, hard, nonmetal brush, and then vacuuming up the loosened dirt and dust. (Vacuuming the dirt after loosening it prevents the dirt from getting deposited on other components.) 6.5.4.
6: Maintenance ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 7: Parts List Section 7 Parts List 7.1 Procedure for ordering parts You should order parts from the nearest authorized Sullair representative or the representative from whom the compressor was purchased. If for any reason you cannot obtain parts in this manner, contact the factory directly at the address, phone number, or website listed below. Sullair North America Operations 1 Sullair Way Michigan City, IN 46360 USA www.sullair.
Service kit part number 250025-526 Qty Description 1 Element for compressor fluid filter 88290002-337 1 Element for heavy duty primary air filter 88290002-207 88290002-338 1 Element for heavy duty secondary air filter 88290002-207 250042-862 1 Primary element for fluid/air separator 02250061-137 1 Secondary element for fluid/air separator 1 Maintenance kit for inlet valve 88292027-255 88292009-685 1 Repair kit for inlet valve 88292027-255 88291010-178 1 Repair kit for pneumatic control
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-151 R03 7: Parts List 46 7.
Key Part number Qty Description Notes 1 829108-150 6 CAPSCREW,HEX GR5 1/2-13 X 1 1/2" 2 837808-125 6 WASHER, SPRLOCK REG PLTD 1/2" 3 88290002-205 1 ADAPTER,MTR-COMP LS16-100 CHNSZ 4 88290002-206 2 GUARD,COUPLING LS16-100 CHNSZ 88290003-311 1 COUPLING,SHAFT VULKAN LS16-75+ FOR 365TSC-4 88290003-312 1 COUPLING,FLEXOMAX-G128/GG VULKAN+ FOR 365TSC-2 88290007-806 1 COUPLING,SHAFT VULKAN LS16-100+ FOR 405TSC-4 6 ———— 1 COMPRESSOR SEE COMPRESSOR LIST 7 88290020-282 2 ISOLATOR
Key Part number Qty Description FOR 365TSC FRAME MOTOR A2 FOR 405TSC FRAME MOTOR A3 FROM AIR INLET FILTER A4 MAIN OIL CONNECTION A5 OIL RETURN FROM SIGHT GLASS ON RECEIVER TANK A6 TO RECEIVER TANK Compressor list 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-152 R01 7: Parts List 50 7.
Key Part number Qty Description 1 02250061-835 1 ELBOW, RUB 90DEG 5"ID 2 408153 2 CLAMP, HOSE 6"DIA WORM DRIVE 3 829108-150 4 CAPSCREW,HEX GR5 1/2-13 X 1 1/2" 4 837808-125 4 WASHER, SPRLOCK REG PLTD 1/2" 5 88290002-207 1 FILTER,AIR LS16 100HP CHNSZ 6 88290002-208 1 BAND,MOUNTING AIR FLTR LS16-100 7 88290004-147 1 GASKET,INL VLV LS12-50 LF SSAI 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-154 R01 7: Parts List 52 7.
Key Part number Qty Description 1 02250101-372 1 SEAL,U-CUP VITON THERM VLV 2 02250196-306 1 VALVE, KP18NV (1/8" NPTF, VITON) 3 49542 1 ELEMENT,THERMAL VALVE 175 4 250025-526 1 ELEMENT,FLUID FILTER 5 826502-144 1 O-RING,VITON 2 1/2 X 3/32 6 88290023-074 1 SWITCH,MANIFOLD OIL FILTER FRAME+ 7 88291008-555 1 HOSE,OIL IN CLR AS45-75AC 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-155 R02 7: Parts List 54 7.
Key Part number Qty Description Notes 1 250022-436 13 WEATHERSTRIP,3/16 X 3/8 FT 2 88291010-006 1 ADAPTER,VENTURI/COOLER AS45-75 88292017-516 1 COOLER,FLUID&AFTER ST45/55 ASME ST45/55 ASME 88292017-517 1 COOLER,FLUID&AFTER ST75 ASME ST75 ASME 88292018-732 1 COOLER,FLUID&AFTER ST45/55 GB ST45/55 GB 88292018-733 1 COOLER,FLUID&AFTER ST75 GB ST75 GB 88292018-870 1 FAN,ST45/55 230/460/6 UL&CSA+ ST45/55 230/460V US 88292018-871 1 FAN,ST75 230/460/6 UL&CSA+ ST75 230/460V US 3 4
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-153 R01 7: Parts List 56 7.
Key Part number Qty Description 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 1 20169 2 CONNECTOR, FLEX 1/4T X 1/4P 2 02250061-137 1 ELEMENT,AIR/OIL SEP SECONDARY 3 02250097-349 1 VALVE,RELIEF 3/4"200#550SCFM W/TEFL 4 02250101-490 2 CONNECTOR,TUBE MALE BHD 1/4 X SAE 5 02250117-782 2 FILTER,ASSEMBLY GENISIS FILTR + 6 02250125-775 1 ORIFICE,PLUG 1/8"NPT .
Key Part number Qty Description 32 88831112-025 4 WASHER,12 GB97.1-85 GAV SSAI 33 88832108-021 4 WASHER,SPRG 8 GB93-87 GAV SSAI 34 88832112-031 8 WASHER,SPRG 12 GB93-87 GAVSSAI 35 88842026-051 1 O-RING,VITON 51.5X2.65GB3452.1 36 88842035-023 1 O-RING,VITON 23.6X3.55GB3452.1 88842035-028 1 O-RING,VITON 28X3.55 GB3452.1 38 88842035-047 1 O-RING,VITON47.5X3.55GB3452.1 39 88842035-069 1 O-RING,VITON 69X3.55 GB3452.1 40 88842035-075 1 O-RING,VITON 75X3.55 GB3452.
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-156 R01 7: Parts List 60 7.
Key Part number Qty Description 1 88290001-541 1 CONNECTOR,SEP-MIN VLV 150AC SSAIC 2 88290005-230 1 ADAPTER,ELBOW ADJUST LS16-75/100 3 88290005-231 1 ADAPTER, LS16-75/100 CHNZ 4 88291011-165 1 HOSE,FLEX DN40 ST45-75 AC 5 88291009-260 1 CONNECTOR,DISC SYS AS45-75AC VSD 6 88291011-118 1 CONNECTOR,DISC SYS ST45-75 AC 7 88291011-207 1 SUPPORT,AIROC AS75 AUS 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-157 R05 7: Parts List 62 7.
Key Part number Qty Description 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 1 02250052-841 6 INSERT,NYL TBG 1/4 OD X .035W 2 02250054-861 6 TUBE,NYL .25 OD X 040W BLK(FT) 3 250003-869 1 INDICATOR, RESTRICTION 20"H20 4 250018-427 1 CONNECTOR, 1/4"TUBE X 1/8"NPT 5 807600-005 1 BUSHING, RED 1/4 X 1/8" STL 6 823202-000 1 NIPPLE, GALV XS 1/8 X CLOSE 7 88290002-119 1 GAUGE,PRES D50 0-1.
Key Part number 30 Qty Description 250018-428 2 CONNECTOR, 1/4"TUBE X 1/4"NPT 31 88290017-336 4 HOSE,HIGH PRESS 1/2X1200 32 860108-050 1 CONNECTOR, 37FL/MPT 1/2 X 1/2" 33 250018-430 1 ELBOW, 1/4"TUBE X 1/4"NPT 34 88292031-784 1 ORIFICE,6.35MM NPT1/2-NPT1/2 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. A1 ATTACH TO FRAME A2 ATTACH TO ENCLOSURE A3 ATTACH TO ENCLOSURE A4 MOTOR WIRING ShopTek™ ST45, ST55, ST75 (U.S.A.
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292017-767 R04 (Sh1) 7: Parts List 66 7.
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 7: Parts List 67 88292017-767 R04 (Sh2) ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 7.
Key Mark Part number Qty Description Notes / 88292018-174 1 CUBICLE 2 / 88292018-669 1 MOUNTING PLATE 88291012-882 2 CONTACTOR ST45 88291012-883 2 CONTACTOR ST55 88292018-173 2 CONTACTOR ST75 88291013-038 1 CONTACTOR ST45 1 CONTACTOR ST55 3 KM1,2 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. ShopTek™ ST45, ST55, ST75 (U.S.A.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 8829019-158 R00 7: Parts List 70 7.
Key Part number 1 02250048-520 2 3 Qty Description Notes PLUG, PLASTIC 1.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions. 88292019-159 R00 7: Parts List 72 7.
Key Part number Qty Description 1 02250069-389 1 DECAL,FLUID SULLUBE 2 02250110-891 1 DECAL,EN-WARNING MIXING FLUIDS 3 02250171-797 1 DECAL, DO NOT BREATH COMP AIR 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
7: Parts List ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 74 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual A: Nominal Sizes Appendix A: Nominal Sizes Metric nominal size (DN) is the nominal size for valves, flanges and fittings as defined by ISO 6708-1980. DN designates the size of all components in a piping system other than components designated by outside diameters or by thread size. For example, steel tubes are designated and ordered by outside diameter and thickness.
A: Nominal Sizes ShopTek™ ST45, ST55, ST75 (U.S.A. & Mexico) Operation & Maintenance Manual Notes: 76 88292021-240 R01 Subject to EAR, ECCN EAR99 and related export control restrictions.
Subject to EAR, ECCN EAR99 and related export control restrictions.
Sullair, LLC 1 Sullair Way Michigan City, IN 46360 USA www.sullair.com 1-800-SULLAIR (USA only) 1-219-879-5451 (non-USA) Information and specifications are subject to change without prior notice. Subject to EAR, ECCN EAR99 and related export control restrictions.