REFRIGERATOR - FREEZER Models CP972SS CP962 Use and Care Guide BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Felix Storch, Inc. Summit Appliance Division An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY10474 www.summitappliance.
TABLE OF CONTENTS 1. IMPORTANT SAFEGUARDS ...................................................................................................................... 2 2. INSTALLATION .............................................................................................................................. 2 - 8 2.1 Location ...................................................................................................................................................... 2 2.
1. IMPORTANT SAFEGUARDS 1) WARNING―Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. 2) WARNING―Do not damage the refrigerant circuit. 3) WARNING―Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
2.2 Reversing the Door Swing Tools Required: Phillips style screwdriver / Flat-bladed screwdriver / Hexagonal wrench Ensure the appliance is unplugged and empty. Adjust the two leveling feet to their highest position. We recommend you have someone to assist you. 1) Remove the right top hinge cover. Right top hinge cover 2) Remove the screws holding the top-hinge with a Phillips screwdriver.
3) Move the top-hinge and the top-door limit block and the door bearing bush to the other side. A. Remove the nut with sleeve. Take off the washer then move the axis to the other side and fix in place. B. Remove the door limit block C. Find the other door limit block, with screw mounting to the door 4) Disassemble the screws holding the bottom-hinge with a Phillips screwdriver. Note: The incline angle of the refrigerator-freezer must be less than 45°.
5) Replace the bottom door bearing bush and the limit block. 6) Replace the bottom hinge to the other side, then fix it with screws. 7) Replace the mid-hinge. 8) Set the bottom door right position, fix the mid-hinge.
9) Replace the top-hinge. 10) Set the upper door into the right position, fix the top-hinge and hinge cover. 11) Install the four screw caps and two catches to the corresponding positions. 12) Replace the leveler to the other side and adjust it to make sure the cabinet is level.
2.3 Door Space Requirements The unit's door must be able to open fully as shown. W×D ≥ 35.5 X 41.4 inch 2.4 Leveling the Unit To do this, adjust the two leveling feet at the front of the unit. If the unit is not level, the door and magnetic seal alignments will not be covered properly. Make sure that the foot touches the ground before use. Look down from the top to check that unit is vertical. Adjust leveling feet as necessary. 2.
2.7 Interior Accessories Various glass or plastic storage shelves are included with your appliance – different models have different combinations. You should always slide one of the full-size glass storage shelves into the lowest set of guides, above the fruit and vegetable container (crisper), and keep it in this position. To do this, pull the storage shelf forward until it can be swiveled upwards or downwards and removed. Do the same in reverse to insert the shelf at a different height.
3. LOCATION OF PARTS Steel shelf Thermostat Refrigerator tray Glass shelf Crisper cover Crisper Adjustable foot *All images in this instruction manual are for indication only; please refer to your individual unit for details.
4. OPERATION 4.1 Switching On Your Unit The temperature selector knob is located on the right hand wall of the refrigerator interior. Setting “Off”：Unit Off Setting “Min”：Less Cool Temperature Setting “Med”：Normal Operation (adequate for most situations) Setting “Max”：Coolest Temperature During high ambient temperatures, e.g., on hot summer days, it may be necessary to set the thermostat to the Coolest setting (position “Max”).
5. CLEANING 5.1 Cleaning the Interior and Exterior of the Unit Remove all the shelves and the crisper. To remove the crisper, first remove the lower door shelf. Wipe the inside of the unit with a weak solution of bicarbonate of soda and then rinse with warm water using a wrung-out sponge or cloth. Wipe completely dry before replacing the shelves and crisper. To clean the stainless steel doors, use a product specifically made to clean this material.
6. MAINTENANCE 6.1 Defrosting This appliance combines a manual defrost freezer compartment and an automatic defrost refrigerator compartment. The refrigerator compartment defrosts itself, but when frost builds to ¼ inch in the freezer compartment, you should defrost it carefully according to this procedure: 1. Remove contents from the freezer, taking care that frozen items do not begin to thaw. Set the temperature selector knob to “Off”. 2. Unplug the appliance.
7. TROUBLESHOOTING The following simple issues can be handled by the user.
8. TIPS FOR ENERGY SAVING Try not to open the doors too often, especially when the weather is damp and hot. Once you open a door, close it as soon as possible. Every now and then check if the appliance is sufficiently ventilated (adequate air circulation behind the appliance). During normal temperature conditions, the thermostat should be placed at the middle setting. Before loading the appliance with packages of fresh food, make sure they are cooled to ambient temperature.
10. LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factoryspecified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
