Manual

ManualsBrandsSunlight Supply ManualsLightingGrozone Control SCC1 Temperature, Humidity and CO2 Controller Simple One Series

1 of 12

Grozone SCC1 Advanced User Guide – March 2012 www.grozonecontrol.com

SCC1 GROZONE CLIMATE CONTROLLER “The Simple One” Series...

ADVANCED USER GUIDE

PRODUCT OVERVIEW

Advanced User Guide - Table of Content

Section

Content

Page

Temperature Control with a Fan – Low Temp and High Temp limits

Temperature and Humidity Control with a Fan

Humidity Control

CO2 Enrichment with a burner or a tank

Output Priorities and Fail States

Factory Settings and Alternate Settings

Accessing the factory / alternate setting edit mode.

 Changing the CO2 Elevation Parameter

 Changing the OUTPUT CONTROL Parameter

 Changing the PRIORITY AND FAIL STATES Parameter

IMPORTANT NOTICE

Basic information on this product are found in the QUICK START USER GUIDE shipped with the unit

also available online at www.grozonecontrol.com.

Quick Start User Guide - Table of Content

Section

Content

Output Descriptions

LED Indicators

Knob Settings

CO2 Sensor Calibration

Temperature Control with Fan (and Optional Heater)

Temperature and Humidity Control with Fan (and Optional Heater)

Humidity Control with a Humidifier or Dehumidifier

CO2 Enrichment with a Burner or a Tank

Summary of content (12 pages)

PAGE 1
SCC1 GROZONE CLIMATE CONTROLLER “The Simple One” Series... ADVANCED USER GUIDE PRODUCT OVERVIEW Advanced User Guide - Table of Content Section 1 2 3 4 5 6 Content Temperature Control with a Fan – Low Temp and High Temp limits Temperature and Humidity Control with a Fan Humidity Control CO2 Enrichment with a burner or a tank Output Priorities and Fail States Factory Settings and Alternate Settings Accessing the factory / alternate setting edit mode.
PAGE 2
1- TEMPERATURE CONTROL WITH FAN (AND OPTIONAL HEATER) To use this mode, you connect your cooling Fan into the FAN 120V Output, set the Slide Switch to “Cooling” position.
PAGE 3
2- TEMPERATURE AND HUMIDITY CONTROL WITH FAN (AND OPTIONAL HEATER) To use this mode, you connect your cooling Fan into the FAN 120V Output, set the Slide Switch to “Cooling & Dehumidifying” position.
PAGE 4
3- HUMIDITY CONTROL WITH A HUMIDIFIER OR DEHUMIDIFIER To use this mode, you connect your Humidity Equipment (Humidifier or Dehumidifier) into the HUMIDITY 120V Output, set the Slide Switch to either “Humidifying” or “Dehumidifying” according to your equipment type.
PAGE 5
4- CO2 ENRICHMENT WITH A BURNER OR A TANK To use this mode, you connect your CO2 Generator into the CO2 120V Output. CO2 Enrichment will work during the DAY ONLY.
PAGE 6
5- OUTPUT PRIORITIES AND FAIL STATES Every CONTROL ACTION taken by the SCC1 is given a priority level. A higher priority action WILL ALWAYS SUPERSEDE any lower priority action. Output Priorities can be modified with the Alternate Settings. See Section 6- on next page.
PAGE 7
6- FACTORY SETTINGS AND ALTERNATE SETTINGS When shipped from the factory, the SCC1 is set with factory settings. These settings are those that a vast majority of users will be using during their growing experiences. Advanced users may need to change some settings in order to fix control problems or to improve control performances in some specific set-ups. Review below the settings that can be changed by the users.
PAGE 8
4 CO2 OUTPUT CONTROL DIFFERENTIAL 5 AUX HEATER OUTPUT CONTROL DIFFERENTIAL FACTORY SETTING ALTERNATE SETTING DURING THE DAY ONLY Stops on setpoint, Starts -200 ppm below setpoint DURING THE DAY ONLY Stops on setpoint, Starts -400 ppm below setpoint FACTORY SETTING ALTERNATE SETTING Competing Equipment Auto Detection is Set Competing Equipment Auto Detection is NOT Set Starts -8°F below setpoint, stops -2°F below setpoint or (*) Starts -12°F below setpoint, stops -6°F below setpoint to avoid Fan a
PAGE 9
10 FAN OUTPUT FAIL STATE 11 AUX FAN OUTPUT FAIL STATE FACTORY SETTING ALTERNATE SETTING The FAN Output is turned ON when a Temperature Sensor Failure is detected, regardless of DAY and NIGHT Temperature Setpoints. The FAN Output is turned OFF when a Temperature Sensor Failure is detected, regardless of DAY and NIGHT Temperature Setpoints.
PAGE 10
Step 4 - Understanding the FACTORY / ALTERNATE SETTING EDIT MODE IMPORTANT: in this mode, the KNOBS and LED INDICATORS take other meanings.      Day Temperature Knob: to select the PARAMETER (among 3). Temperature Indicators: to indicate the selected PARAMETER. Pushbutton: to select the right setting (up to 6 settings per PARAMETER) Day Humidity Knob: to change the setting values. Humidity and CO2 Indicators (A to F): to indicate the setting values.
PAGE 11
CHANGING THE OUTPUT CONTROL PARAMETER     Turn the SELECT knob (Day Temperature) to position 2. The two top PARAMETER indicators will lit. CLICK the Pushbutton to select the VALUE Indicator (A to F) you need to turn ON (Lit) or OFF. Rotate the SET/RESET knob (Humidity Temperature) to turn ON/OFF the selected indicator (selected indicator is flashing; flashing will stop once value has been set or reset). To EXIT and SAVE, make sure to move through all 6 indicators.
PAGE 12
CHANGING THE PRIORITY AND FAIL PARAMETER     Turn the SELECT knob (Day Temperature) to position 3. The three PARAMETER indicators will lit. CLICK the Pushbutton to select the VALUE Indicator (A to F) you need to turn ON (Lit) or OFF. Rotate the SET/RESET knob (Humidity Temperature) to turn ON/OFF the selected indicator (selected indicator is flashing; flashing will stop once value has been set or reset). To EXIT and SAVE, make sure to move through all 6 indicators.