Operation Manual
15
ENGLISH
Adjustable back sling
The adjustable back sling can be
adjusted for tension by using
several straps.
The back sling upholstery can be
accessed from the inside via an
opening and can be padded to suit
Fig. 5.23
Height-adjustable backrest
The backrest may be set to
various back heights, in 2.5 cm
steps. The adjustment ranges are
25- 30 cm, 30- 35 cm, 35- 40 cm
and 40- 45 cm. Release the
to the desired height. Tighten up
Fig. 5.24
1
2
Push Handles
Height-adjustable push handles
These handles are secured with pins
to prevent them from sliding out
unintentionally. Opening the quick-
adjust the height of the push handles
you move the lever, you will hear a
locking mechanism; you can now
easily position the push handle as
desired. The nut on the tension lever
determines how tightly the push
handles are clamped into place. If the nut is loose after adjusting
the tension lever, the push handle will also be too loose. Turn
the push handle from side to side before use to make sure that it
is clamped securely enough into place. After adjusting the
place. If the lever is not secure, injuries could result when
NOTE – If the height-adjustable push handles are not fitted
properly, there is a risk that these will develop "play" or that they
move out of position. Please make sure that the relevant screws
are tightened correctly.
Fold-down push handles
If the push handles are not in use,
they can be folded down depressing
again, simply flip them back up until
1
2
Fig. 5.29
SINGLE POST HEIGHT-ADJUSTABLE ARMRESTS
1. Installation
a. Slide the outer armpost into the
receiver mounted to the wheelchair
frame.
b. The armrest will automatically lock into
place.
2. Height Adjustment
second stop.
b. Slide armrest pad up or down to
desired height.
c. Return lever to locked position against arm post.
3. Removing Armrest
a. Pull lever 3 and lift entire arm.
4. Replacing Armrest
a. Slide armrest back into receiver until arm latches in place.
ARMREST RECEIVER ATTACHMENT
Adjusting Armrest Receiver Fit
To tighten or loosen the fit of the outer
armpost in the receiver:
1. Loosen the four receiver adjustment
squeeze the receiver to achieve the
desired fit.
Position Adjustment
clamp is loose.
2. Slide armrest receiver to desired
position.
3. Tighten
Anti-Tip Tubes
WARNING !
Sunrise Medical recommends anti-tip tubes for all chairs. When
fitting anti-tip tubes, use a torque of 7 Nm.
1. Slotting the anti-tip tubes into the
clamp:
a. Press the rear button on the anti-tip
tube on the anti-tip tube adapter, so
that both release pins are drawn
inwards.
anti-tip tube adapter.
c. Turn the anti-tip tubes downwards
until the release pin locks into the
clamp.
d. Fit the second anti-tip tube in the same way.
2. Adjusting the anti-tip tubes
Press the anti-tip tube release button, so that both release pins
are drawn inwards. Move the inner tube up or down to slot into
the height holes provided. Release the button. Fit the second
anti-tip wheel in the same way. Both wheels should be at the
DANGER !
If the anti-tip tubes are not fitted, or have been fitted incorrectly,
there is a risk of tipping over and of injury.
Fig. 5.31
Crutch holder
Crutch holder
This device permits crutches to be transported directly on the
CAUTION!
Never try to use or even remove the crutches or other aids while
moving.
Sideguard
1. Outer armpost
2. Height Release Lever
3. Release lever
4. Armrest pad
5. Transfer bar
6. Side panel
7. Receiver
8. Clamp
9. Receiver adjustment ardware
10. Clamp bolts
E
Fig.5.28
1
3
6
2
5
9
7
4
Fig. 5.25
10
7
8
9
Fig. 5.26
9
10
D
Fig. 5.27
Fig. 5.30
2