SUPER SC942S-600 SC942i-600/550 SC942 CHASSIS INSTALLATION GUIDE 1.
SUPER SC942 Chassis User's Guide Table of Contents Chapter I: Unpacking and Check Lists .................................... 1-3 Chapter 2: Installation Procedures ........................................... 2-1 Section 1: Installing components into the SC942 Chassis ............. 2-1 A. Removing the Side Cover of the SC942 Chassis ................................ 2-1 B. Removing the SCSI Drive Trays .............................................................. 2-2 C.
Chapter 1: Unpacking and Check Lists Chapter 1- Unpacking and Check Lists 1-A. The SC942S-600 chassis The SC942S chassis contains the following: One (1) 5.25" drive bay (for floppy drive) Two (2) 5.
SUPER SC942 Chassis User's Guide 1-B. The SC942i chassis The SC942i chassis contains the following: Eight (8) 5.25" peripheral drive bays One (1) 5.25" drive bay for floppy drive Three (3) Hot-swappable120mm chassis fans (*SC 942i-600) Two (2) Hot-swappable120mm chassis fans (*SC 942i-550) One (1) 120mm Rear Exhaust fan Two (2) Front accessible USB 2.
Chapter 2: Installation Procedures Chapter 2: Installation Procedures Section 1: Installing Components into the SC942 Chassis A. Removing the Side Cover of the SC942 Chassis Before installing any components, replacing chassis fans or accessing the motherboard, you will first need to remove the side cover. Procedures 1. Remove the two screws from the back lip of the side cover (-this is the left cover when you looking from the front.) Remove the screws 2.
SUPER SC942 Chassis User's Guide B. Removing the SCSI Drive Trays (*SC942S) Procedures 1.Pull out the SCSI Drive Trays located on the front side of the chassis(*SC942S only) Pull the SCSI Drive Trays outwards 2. Pull the SCSI Drive Bay outwards, and press the release tab located on the SCSI Drive Bay. Then, you can access the SCSI Drive.
Chapter 2: Installation Procedures C. Removing the Rear Exhaust Fan and Installing the Motherboard (You will need to remove the rear exhaust fan before you install the motherboard.) Procedures 1. Remove the side cover from the chassis (refer to Section A). 2. Locate the exhaust fan tabs on the back panel (See picture below right.) 3. Apply pressure to the tabs (located on the top and the bottom of the rear exhaust fan) to snap the fan out of its locked position. 4. Pull the fan away from the chassis.
SUPER SC942 Chassis User's Guide D. Removing Components from and Installing Devices into the 5.25" Drive Bays After removing the side cover from the chassis, you can remove or install devices into the drive bays (See Section A for removing the side cover). Procedures 1. Remove the side cover to access the 5.25" drive bays. 2. Remove the screws of the bay you wish to install or remove a component from. (*The chassis comes with dummy modules in all bays to maintain adequate airflow.
Chapter 2: Installation Procedures E. Installing the Rear Chassis Lock Follow the procedures listed below to install the Rear Chassis Lock. Procedures 1. Locate the hole at the right bottom corner of the rear side of the chassis. Also locate the lock bracket included in your shipping package. lock bracket Hole for the lock bracket 2.
SUPER SC942 Chassis User's Guide 3. Slide the side cover back to the proper position. Make sure that the lock bracket is easily accessible from the rear of the chassis. Lock Bracket 4.
Chapter 2: Installation Procedures F. Removing the Front Side Cover to Access the Drives (You do not need to remove the front bezel to access the drives. We do not recommend removing the front cover unless you need to access the control panel circuit board or the floppy drive.) Procedures 1. Remove the side cover from the chassis (See Section A). 2. Push on the three tabs located inside the bottom side lip of the front chassis cover. 3. Locate the 4 notches inside the side lip.
SUPER SC942 Chassis User's Guide 4. Push on the open side of cover to completely remove it from the chassis. (*Do not swing or pull the front cover straight out after opening the left side.) 5. You can also remove the control panel's circuit board by removing the screw that fastens the control panel to the chassis.
Chapter 2: Installation Procedures Section 2: Installing the SC942 as a Rackmount G. Rackmount Rail Kit: CSE-PT26 (* CSE-PT26 Sold separately.
SUPER SC942 Chassis User's Guide H. Removing the Top Chassis Cover and Chassis Feet to Install as Rackmount Procedures 1. Remove the side cover from the chassis (See Section A). 2. Press the release tab in the center of the cover lip while pushing the cover toward the rear of the chassis at the same time. After the cover stops, lift it off. Press the Release Tab 3. Each chassis foot has a single screw. Remove the screw, then, depress the foot's locking tab from inside of the chassis. Slide the foot off.
Chapter 2: Installation Procedures I. Attaching Chassis Ears to the Chassis After you have removed chassis feet from the chassis, you can now attach chassis ears to the chassis. Procedures 1. Remove the chassis feet from the chassis (See Section H). 2. Locate a pair of chassis ears and two sets of screws (3-each set) included in the shipping package, and lay the chassis on a flat level as shown below. Screws Chassis Ears Screws 3.
SUPER SC942 Chassis User's Guide J. Installing Chassis Rails After you have attached the chassis ears to the chassis, you can install chassis rails to the chassis for rackmount purpose. Procedures 1. Included in the shipping package are a pair of rail assemblies. In each rail assembly, locate the inner rail and the outer rail. Outer rail (*to be installed in the rack) Press the Locking Tab Pull out the Inner rail (*to be attached on the chassis) Rail Assembly 2.
Chapter 2: Installation Procedures K. Rack Installation After you have installed the inner rails and chassis ears to the chassis, you are ready to install the outer rails of rail assemblies to the rack. Procedures 1. In the package, locate a pair of short brackets, and a pair of long brackets. Please note that there are "R"(-Right) and "L"(-Left) marked on the short and long brackets.
SUPER SC942 Chassis User's Guide 5. Align brackets flush against the racks and tighten two screws through the holes of the rack (as shown below) and repeat the same step to install the rack on the other side. Use two M5 screws and washers to attach the bracket to the rack. 6. Once both outside rails are securely installed on the rack, you are ready to mount the SC942 to the rack.
Chapter 2: Installation Procedures 7. To mount the SC942 on the rack, first you need to align both of the inner slides that are attached on the SC942 against the outer rails as shown below: Outer rails Inner rails 8. Slide the SC942 Assemblies all the way to the back of the slide rails to ensure that the assemblies are securely latched on the ball bearing slides. (The SC942 may not slide in smoothly or easily into the rack when installed the first time.
SUPER SC942 Chassis User's Guide 9. Secure the SC942 by tightening the screws on the sides of the SC942 as shown above.
Appendix A CSE-M35S/CSE-M35T1 Mobile Rack User's Guide Rev. 1.
SUPER SC942 Chassis User's Guide CSE-M35S/CSE-M35T1 Supermicro’s CSE-M35S/CSE-M35T1 Mobile Rack Series offers the cutting edge technology with greater flexibility. The CSE-M35T1 supports five Serial ATA hot-swappable hard drives that yield a unparalleled storage capacity without compromising productivity by eliminating possible system downtime.The CSE-M35S also accommodates five SCSI SCA 320/160 Hard drives which provide configuration flexibility and maximum data integrity. A.
Appendix A: SUPER CSE-M35S/CSE-M35T1 User's Guide B. Technical Specifications Occupancy Capacity Cooling Subsystem System Monitoring Dimension (WxHxD) Weight Three (3) 5.
SUPER SC942 Chassis User's Guide C. Jumper Settings C-1. Jumper Settings for the CSE-M35S (SCSI): Jumper JP18 Description Buzzer Reset JP21 SCSI Termination JP24 SCSI ID Selection JP29 GEM 318 IDs JP30 Fan Sense Setting Closed: Enable, Open: Disable (*Default) Closed: Enable (*Default), Open: Disable 1-2: SCSI Ids: 0,1,2,3,4 (*Default), 2-3: SCSI Ids: 9,10,11,12,13 1-2: ID6 (*Default), 2-3: ID8 Pins 1-2: Enable (*Default) (If a fan is not present, the alarm will sound.
Appendix A: SUPER CSE-M35S/CSE-M35T1 User's Guide C-2.
SUPER SC942 Chassis User's Guide D. Installation Procedures D-1. Accessing Hot Swappable Drives: 1.Push the release button located beside the drive LEDs (as shown below:) 2. Swing the handle outward and pull out the unit (as shown below:) 3.
Appendix A: SUPER CSE-M35S/CSE-M35T1 User's Guide D-2. Accessing the Exhaust Fan: 1.Push the tabs located on both sides of the unit (as low:) shown be- 2. Pull out the fan (as shown below:) (*Note: For the SC-942 Chassis, the CSE-M35 Rear Exhaust Fan should not be used. Instead, the hot-swappable 120mm Chassis Fans included with the SC-942 Chassis should be connected to the Backplane of the CSE-M35S/CSE-M35T1 Mobile Rack.
SUPER SC942 Chassis User's Guide D-3. Accessing the Drive Backplane: 1. Unscrew the screw located on the side of the unit (as below:) 2. Pull out the Rear Bracket (as shown below:) 3.
SUPER SC942 Chassis User's Guide Appendix B Power Supply Specifications Please refer to the following table for Power Supply Specifications: Power Supply Spec SC942S-600 SC942i-600 SC942i-550 Model # Part # SP602-TS PWS-044 SP602-TS PWS-044 SP550-RP PWS-046 Rated AC Input Voltage 100-240V AC Rated Input Frequency 50-60 Hz 100-240V AC 50-60 Hz 100-240V AC 50-60 Hz Rated Input Current 12A (115V) 6A (230V) 12A (115V) 6A (230V) 9A (115V) 4.
Appendix B: Power Supply Specifications Notes B-2
SUPER SC942 Chassis User's Guide Appendix C SCSI (Super) GEM Driver Installation Instructions for Windows OS Please refer to the following instructions to install Driver for the Windows OS systems. the SCSI GEM (*Note: This driver is not necessary for other Operating Systems.) If you have two SCA backplanes, you will need to install the driver twice. The driver is located on the Super Micro motherboard driver CD or is available for download from our FTP site: ftp://ftp.supermicro.
Appendix C: Installation Instuctions for the SCSI GEM Driver 5) At the first prompt, choose “Display a list of known device drivers for the device so that I can choose a specific driver” and click "Next". 6) Choose “Other Devices” and click Next. 7) Choose “Have Disk”, and specify your floppy drive location in the options box. Then, click "Next". 8) Highlight “Enclosure Services Device” and click "Next". 9) Ignore the warning prompt by clicking "Yes".
