X8ST3-F X8STE USER’S MANUAL Revision 1.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc.
Preface Preface This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the X8ST3-F/X8STE motherboard. About This Motherboard The X8ST3-F/X8STE supports the Intel® Core™ i7 processor and Intel® Xeon® 5500/3500 series processors in the LGA 1366 package.
X8ST3-F/X8STE User’s Manual Conventions Used in the Manual: Special attention should be given to the following symbols for proper installation and to prevent damage done to the components or injury to yourself: Danger/Caution: Instructions to be strictly followed to prevent catastrophic system failure or to avoid bodily injury Warning: Important information given to ensure proper system installation or to prevent damage to the components Note: Additional Information given to differentiate various models or
Contacting Supermicro Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.
X8ST3-F/X8STE User’s Manual Table of Contents Preface About This Motherboard................................................................................................. 3 Manual Organization...................................................................................................... 3 Conventions Used in the Manual:.................................................................................. 4 Contacting Supermicro..........................................................................
Table of Contents Universal Serial Bus (USB)....................................................................... 2-12 Ethernet Ports........................................................................................... 2-13 Serial Ports................................................................................................ 2-14 Video Connector........................................................................................ 2-15 Front Control Panel......................................
X8ST3-F/X8STE User’s Manual IPMI Dedicated LAN LEDs (X8ST3-F Only)............................................. 2-34 SAS Activity LED (X8ST3-F Only)............................................................ 2-35 SAS Heartbeat LED (X8ST3-F Only)........................................................ 2-35 Onboard Power LED ............................................................................................................. 2-36 2-9 Serial ATA and Floppy Drive Connections...........................
Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. Please check that the following items have all been included with your motherboard. If anything listed here is damaged or missing, contact your retailer.
X8ST3-F/X8STE User’s Manual X8ST3-F Image Note: All graphics shown in this manual were based upon the latest PCB Revision available at the time of publishing of the manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.
Chapter 1: Introduction KB/MOUSE Motherboard Layout SMBUS_PS1 JPW2 USB 0/1 FAN1 JPW1 DIMM3A IPMI_LAN JPUSB1 CPU FAN DIMM3B DIMM2A COM1 DIMM2B LAN CTRL for IPMIl LAN DIMM1A DIMM1B JLED VGA LAN CTRL1 LE1 North Bridge 1 LAN2 JF1 LAN1 Intel X58-Express Intel Processor JOH JWD JD1 FAN2 Battery LAN CTRL2 SPKR1 X8ST3-F/X8STE Slot5 PCI-E 2.
X8ST3-F/X8STE User’s Manual X8ST3-F/X8STE Quick Reference KB/MOUSE 62 USB 0/1 3 59 SMBUS_PS1 JPW2 FAN1 JPW1 DIMM3A CPU FAN DIMM3B 58 DIMM2A DIMM2B COM1 2 JPUSB1 60 IPMI_LAN 1 61 LAN CTRL for IPMIl LAN DIMM1A DIMM1B LAN CTRL1 JLED VGA 4 JF1 LAN1 55 1 6 North Bridge Intel Processor LAN2 5 57 56 LE1 Intel X58-Express JOH SPKR1 I-SATA0 USB 6/7 10 JPG1 LSI 1068E BMC JTAG SAS1 JPS2 11 USB3 12 16 1 29 JPUSB2 JL1 35JPS1 LES1 FAN3 32 26 17 18 20 21 22 23 39 3
Chapter 1: Introduction X8ST3-F/X8STE Jumpers JPUSB3 #19 FP USB 2, 3 Wake-up Pins 1-2 (Enabled) JWD #53 Watch Dog Timer Enable Pins 1-2 (Reset) X8ST3-F/X8STE Headers/Connectors Connector Label Description Battery #45 Onboard battery (B1) COM1/COM2 #3, 11 COM1/2 Serial connection headers Fans 1~5 #58, 52, 34, 33, 7 System/CPU fan headers (Fan 1: CPU fan) Floppy #12 Floppy Disk Drive connector I-Button #42 I-Button for RAID data storage JAR #50 Alarm Reset JD1 #51 Speaker header
X8ST3-F/X8STE User’s Manual Motherboard Features CPU • Single Intel® Core™ i7 and Intel® Xeon® 5500/3500 series processors in the LGA 1366 socket package. Memory • Six 240-pin, DDR3 SDRAM DIMM sockets with support for unbuffered ECC or non ECC 1333/1066/800 MHz memory. Note: Both Unbuffered ECC and Non-ECC DIMM modules are supported by the motherboard. Using ECC or Non-ECC memory on your motherboard depends on the CPU installed. Please see page 3-3 for more information on memory support.
Chapter 1: Introduction • Supports RAID 0, 1 , 10 under the Linux OS environment SAS Connections (for the X8ST3-F only) • • • Eight (8) SAS ports supported by the LSI 1068E Controller Supports RAID 0, 1, 5*, 10 under the Windows OS environment Supports RAID 0, 1 , 5*, 10 under the Linux OS environment Notes: 1. RAID 5 is supported when the I-Button (AOC-IButton68) is installed on the motherboard. For more information on the AOC-IButton68, please refer to http://www.supermicro.
X8ST3-F/X8STE User’s Manual • • • • • Main switch override mechanism Keyboard Wake-up from Soft-Off USB Wake-up from Soft-Off Wake-on-LAN Power-on mode for AC power recovery PC Health Monitoring CPU Monitoring • Onboard voltage monitors for CPU core, Memory Voltage, Chipset Voltage, +1.8V, +3.3V, +3.
Chapter 1: Introduction Notes 1-9
X8ST3-F/X8STE User’s Manual DIMM_CHA Intel Intersil VRD 11.1 DIMM_CHB LGA1366_PROCESSOR DIMM_CHC DDR3:1333/1066/800 IDT QPI: Up to 6.40 GT/s CK505 CLK PCIE_x 8 SAS1068E PCIE_x8 SAS x 8 Intel X58 PCIE_x 8 PCIE_x 4 DMI RJ45 PCIE_x 8 RJ45 INTEL 82574L x 2 Intel PCI_32_BUS ICH10R USB2.
Chapter 1: Introduction 1-2 Chipset Overview Built upon the functionality and the capability of the Intel X58 Express chipset, the X8ST3-F/X8STE motherboard provides the performance and feature set required for single-processor-based high-end systems with configuration options optimized for intensive application and high-end server platforms.
X8ST3-F/X8STE User’s Manual 1-3 PC Health Monitoring This section describes the PC health monitoring features of the X8ST3-F/X8STE. These features are supported by an onboard System Hardware Monitor chip. Recovery from AC Power Loss BIOS provides a setting for you to determine how the system will respond when AC power is lost and then restored to the system.
Chapter 1: Introduction key, the CPU will wake-up and the LED indicator will automatically stop blinking and remain on. BIOS Support for USB Keyboard If the USB keyboard is the only keyboard in the system, it will function like a normal keyboard during system boot-up. Main Switch Override Mechanism When an ATX power supply is used, the power button can function as a system suspend button. When the user presses the power button, the system will enter a SoftOff state.
X8ST3-F/X8STE User’s Manual It is strongly recommended that you use a high quality power supply that meets ATX12V standard power supply Specification 1.1 or above. It is also required that the 12V 8-pin power connection (JPW2) be used for adequate power supply. In areas where noisy power transmission is present, you may choose to install a line filter to shield the computer from noise. It is recommended that you also install a power surge protector to help avoid problems caused by power surges.
Chapter 1: Introduction The WPCM450 also includes the following features: • One X-Bus parallel interface for expansion I/O connections • Three ADC inputs, Analog and Digital Video outputs • Two serial for boundary scan and debug Note: For more information on IPMI configuration, please refer to the Embedded IPMI User's Guide posted on our website @ http://www.supermicro.com/support/manuals/.
X8ST3-F/X8STE User’s Manual Notes 1-16
Chapter 2: Installation Chapter 2 Installation 2-1 Static-Sensitive Devices Electrostatic-Discharge (ESD) can damage electronic components. To prevent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD. Precautions • Use a grounded wrist strap designed to prevent static discharge. • Touch a grounded metal object before removing the board from the antistatic bag.
X8ST3-F/X8STE User's Manual 2-2 Processor and Heatsink Installation ! When handling the processor package, avoid placing direct pressure on the label area of the fan. Notes: 1. Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink. 2. Intel's boxed processor package contains the CPU fan and heatsink assembly.
Chapter 2: Installation CPU 4. After removing the plastic cap, using your thumb and the index finger, hold the CPU at the north and south center edges. 5. Align the CPU key, the semi-circle cutout, against the socket key, the notch below the gold color dot on the side of the socket. 6. Once both the CPU and the socket are aligned, carefully lower the CPU straight down into the socket. (Do not rub the CPU against the surface of the socket or its pins to avoid damaging the CPU or the socket.
X8ST3-F/X8STE User's Manual Installing a Passive CPU Heatsink (#SNK-P0037) Screw#4 Note: A heatsink bracket (BKT0023L) is required for a screw-type heatsink (-which is a non-pushpin heatsink as shown on the right.) The required heatsink bracket (BKT-0023L) can be purchased from Supermicro. Note: Do not apply any thermal grease to the heatsink or the CPU die because the required amount has already been applied. 1.
Chapter 2: Installation 4. Finish the installation by fully tightening all four screws. Do not over-tighten to avoid possible damage to the CPU. Passive Heatsink Removal 1. Unplug the power cord from the power supply. 2. Using a screwdriver, loosen and remove the heatsink screws from the motherboard in the sequence as shown in the picture on the right. Using a screwdriver to Remove Screw#1 3. Hold the heatsink as shown and gently loosen it from the CPU by moving it from side to side.
X8ST3-F/X8STE User's Manual 2-3 Mounting the Motherboard into the Chassis All motherboards have standard mounting holes to fit different types of chassis. Make sure that the locations of all mounting holes for the motherboard and the chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.
Chapter 2: Installation 2-4 Installing and Removing the Memory Modules Note: Check the Supermicro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Press down the release tabs Installing & Removing DIMMs 1. Insert the desired number of DIMMs into the memory slots, starting with DIMM1A. When populating multiple DIMM modules within a channel, always start with Bank1 first.
X8ST3-F/X8STE User's Manual Memory Support The X8ST3-F/X8STE supports up to 24 GB Unbuffered ECC or Non ECC DDR3 1333/1066/800 in 6 DIMM slots.
Chapter 2: Installation Possible System Memory Allocation & Availability System Device Size Physical Memory Remaining (-Available) (4 GB Total System Memory) Firmware Hub flash memory (System BIOS) 1 MB 3.99 GB Local APIC 4 KB 3.99 GB Area Reserved for the chipset 2 MB 3.99 GB I/O APIC (4 Kbytes) 4 KB 3.99 GB PCI Enumeration Area 1 256 MB 3.76 GB PCI Express (256 MB) 256 MB 3.51 GB PCI Enumeration Area 2 (if needed) -Aligned on 256-MB boundary- 512 MB 3.01 GB VGA Memory 16 MB 2.
X8ST3-F/X8STE User's Manual 2-5 Connectors/IO Ports The I/O ports are color coded in conformance with the PC 99 specification. See the figure below for the colors and locations of the various I/O ports. X8ST3-F/X8STE Back Panel Connectors and IO Ports 2 1 5 4 6 7 3 Back Panel Connectors 1. Keyboard (Purple) 2. PS/2 Mouse (Green) 3. USB Port 0 4. USB Port 1 5. IPMI LAN (X8ST3-F) 6. COM 1 7. VGA 8. LAN1 9.
Chapter 2: Installation ATX PS/2 Keyboard and PS/2 Mouse Ports PS/2 Keyboard/Mouse Pin Definitions The ATX PS/2 keyboard and PS/2 mouse are located next to the Back Panel USB Ports 0/1 on the motherboard. See the table at right for pin definitions.
X8ST3-F/X8STE User's Manual Universal Serial Bus (USB) Two Universal Serial Bus ports (USB 0/1) are located on the I/O back panel. Additional six USB connections (USB 2, USB 3, USB 4/5 and USB 6/7) are used to provide front chassis access. USB 2 and USB 3 are Type A Connectors. (USB Cables are not included). See the tables on the right for pin definitions.
Chapter 2: Installation Ethernet Ports Two Ethernet ports are located next to the VGA port on the IO Backplane. In addition, an IPMI Dedicated LAN is located above the USB ports. These ports accept RJ45 type cables. Notes: 1. The IPMI Dedicated LAN is for the X8ST3-F only. 2. Please refer to the LED Indicator Section for LAN LED information.
X8ST3-F/X8STE User's Manual Serial Ports A COM Port is located on the IO Backplane and a Serial port is located next to the Floppy Drive to provide front access. See the table on the right for pin definitions. Serial Port Pin Definitions (COM1/COM2) Pin # Definition Pin # CDC 6 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 Ground 10 NC 1. COM1 X8ST3-F/X8STE 2.
Chapter 2: Installation Video Connector A Video (VGA) connector is located next to the COM Port on the IO backplane. This connector is used to provide video and CRT display. Refer to the board layout below for the location. Note: If you decide use an add-on VGA card instead, you will need to disable this device using jumper JPG1. Please see page 1-4 for the jumper location. X8ST3-F/X8STE 1.
X8ST3-F/X8STE User's Manual Front Control Panel JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are designed specifically for use with Supermicro server chassis. See the figure below for the descriptions of the various control panel buttons and LED indicators. Refer to the following section for descriptions and pin definitions.
Chapter 2: Installation Front Control Panel Pin Definitions NMI Button NMI Button Pin Definitions (JF1) The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions. Pin# Definition 19 Control 20 Ground Power LED Pin Definitions (JF1) Power LED The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table on the right for pin definitions. Pin# Definition 15 +5V 16 Ground A. NMI B.
X8ST3-F/X8STE User's Manual HDD LED The HDD LED connection is located on pins 13 and 14 of JF1. Attach a hard drive LED cable here to display disk activity (for any hard drive activities on the system, including Serial ATA and IDE). See the table on the right for pin definitions.
Chapter 2: Installation Overheat (OH)/Fan Fail LED Connect an LED cable to the OH/ Fan Fail connection on pins 7 and 8 of JF1 to provide advanced warnings for chassis overheat or fan failure. Refer to the table on the right for pin definitions.
X8ST3-F/X8STE User's Manual Reset Button The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset switch on the computer case to reset the system. Refer to the table on the right for pin definitions. Reset Button Pin Definitions (JF1) Pin# Definition 3 Reset 4 Ground Power Button The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both pins will power on/off the system.
Chapter 2: Installation 2-6 Connecting Cables This section provides brief descriptions and pin-out definitions for onboard headers and connectors. Be sure to use the correct cable for each header or connector. • For information on Backpanel USB and Front Panel USB ports, refer to Page 2-14. • For information on COM Port 1 and COM Port 2, please see Page 2-16.
X8ST3-F/X8STE User's Manual Fan Headers The X8ST3-F/X8STE has five fan headers (Fan1 ~ Fan5). Fans 2~5 are system cooling fans. Fan 1 is used as a CPU fan. These fans are 4-pin fan headers. However, Pins 1-3 of the fan headers are backward compatible with the traditional 3-pin fans. The default setting is Disabled which allows the onboard fans to run at full speed. Refer to the table on the right for pin definitions.
Chapter 2: Installation Internal Buzzer Internal Buzzer Pin Definition The Internal Buzzer (SPKR1) can be used to provide audible indications for various beep codes. See the table on the right for pin definitions. Refer to the layout below for the locations of the Internal Buzzer. Pin# Definitions Pin 1 Pos. (+) Beep In Pin 2 Neg. (-) Alarm Speaker Speaker Speaker Connector Pin Definitions KB/MOUSE On the JD1 header, Pins 3~4 are used for internal speaker.
X8ST3-F/X8STE User's Manual Overheat/Fan Fail LED Overheat LED Pin Definitions The JOH header is used to connect an LED to provide warnings of chassis overheat. This LED will also blink to indicate a fan failure. Refer to the table on right for pin definitions.
Chapter 2: Installation Power Supply I2C Connector PWR Supply I2C Pin Definitions Power Supply (I C) Connector, located at SMB_PS1 on the motherboard. This connector monitors the status of the power supply, fan and system temperature. See the table on the right for pin definitions. 2 Pin# Definition 1 Clock 2 Data 3 PWR Fail 4 Ground Onboard Power LED Onboard PWR LED Pin Definitions An onboard Power LED header is located at JLED1.
X8ST3-F/X8STE User's Manual T-SGPIO 0/1 & 3-SGPIO 0/1 Headers Serial_Link-SGPIO Pin Definitions Two T-SGPIO (Serial-Link General Purpose Input/Output) headers are located next to the I-SATA Port 1 on the motherboard. Additionally, two 3-SGPIO ports are also located next to SAS Port 3 on the X8ST3-F motherboard. These headers are used to communicate with the enclosure management chip in the system. See the table on the right for pin definitions.
Chapter 2: Installation Wake-On-LAN Wake-On-LAN Pin Definitions (JWOL) The Wake-On-LAN header is located at JWOL on the motherboard. See the table on the right for pin definitions. (You must also have a LAN card with a WakeOn-LAN connector and cable to use this feature.) Pin# Definition 1 +5V Standby 2 Ground 3 Wake-up I-Button An onboard I-Button, located next to USB Ports 2~3, is an 1-wire computer chip enclosed in a durable stainless steel can.
X8ST3-F/X8STE User's Manual 2-7 Jumper Settings Explanation of Jumpers To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.
Chapter 2: Installation CMOS Clear JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such as a small screwdriver to touch both pads at the same time to short the connection. Always remove the AC power cord from the system before clearing CMOS. Note: For an ATX power supply, you must completely shut down the system, remove the AC power cord and then short JBT1 to clear CMOS.
X8ST3-F/X8STE User's Manual SMB to PCI-X/PCI-E Slots Speeds SMBus to PCI-X/PCI-Exp Slots Jumper Settings Use Jumper JI2C1 to connect the System Management Bus to the PCI slots, and Jumper JI2C2, to the PCI-Exp. slots in order to improve power management for PCI-X and PCI-E slots. The default setting is to close pins 2-3 to disable the function. See the table on the right for jumper settings.
Chapter 2: Installation USB Wake-Up JPUSB1 (BackPanel USB 0/1 Wake-up Enable) Use JPUSB jumpers to "wake-up" your system by pressing a key on a USB keyboard or clicking the USB mouse of your system. The JPUSB jumpers are used together with the USB Wake-Up feature in the BIOS. Enable both USB jumpers and the USB feature in the BIOS to wake-up your system via USB devices. See the table on the right for jumper settings and jumper connections.
X8ST3-F/X8STE User's Manual SAS Enable/Disable (X8ST3-F Only) SAS Enable/Disable Jumper Settings JPS1 allows you to enable or disable SAS Connectors. The default position is on pins 1 and 2 to enable SAS. See the table on the right for jumper settings. Jumper Settings Enabled (Default) Pins 2-3 Disabled SAS RAID Mode Select (X8ST3-F Only) Software RAID Jumper Settings KB/MOUSE JPS2 allows you to select the SAS RAID mode. You can use either Software RAID or IT Mode.
Chapter 2: Installation BMC IPMI Enable (X7ST3-F only) KB/MOUSE JBMC1 allows the user to enable or disable BMC (Baseboard Management Control) Chip and the onboard IPMI connections. This jumper is to be used together with the IPMI settings in the BIOS. If this jumper is set to Enabled, please enable IPMI settings in the BIOS as well and vice versa. The default position is on pins 1 and 2 to Enable BMC. See the table on the right for jumper settings.
X8ST3-F/X8STE User's Manual 2-8 Onboard Indicators LAN 1/LAN 2 Link/Speed LED Activity LED LAN 1/LAN 2 LEDs LAN 1/LAN 2 Rear View (when facing the rear side of the chassis) Two LAN ports (LAN 1/LAN 2) are located on the IO Backplane of the motherboard. Each Ethernet LAN port has two LEDs. The yellow GLAN Activity LED (right, see above right) indicates activity, while the GLAN Link/ Speed LED (left) may be green, amber or off to indicate the speed of the connection.
Chapter 2: Installation SAS Activity LED (X8ST3-F Only) A SAS Activity LED is located at LES1. When LES1 blinks, SAS is active. Refer to the table on the right for details. Also see the layout below for the LED location. SAS Activity LED Indicator LED Settings Blinking: Green SAS is active SAS Heartbeat LED (X8ST3-F Only) A SAS Heartbeat LED is located at LES2. When LES2 blinks, SAS connectors are ready for use. Refer to the table on the right for details. Also see the layout below for the LED location.
X8ST3-F/X8STE User's Manual Onboard Power LED Onboard PWR LED Indicator LED Settings An Onboard Power LED is located at LE1 on the motherboard. When LE1 is on, the AC power cable is connected. Make sure to disconnect the power cable before removing or installing any component. See the layout below for the LED location.
Chapter 2: Installation 2-9 Serial ATA and Floppy Drive Connections Note the following conditions when connecting the Serial ATA and floppy disk drive cables: • Be sure to use the correct cable for each connector. Refer to Page 1-1 for cables that came with your shipment. • A red mark on a wire indicates the location of pin 1. SATA Connectors SATA Connectors Pin Definitions Six Serial ATA (SATA) connectors (I-SATA 0~5) are located on the motherboard to provide serial link connections.
X8ST3-F/X8STE User's Manual Floppy Connector Floppy Drive Connector Pin Definitions The floppy connector is located near the PCI Slot 1 on the motherboard. See the table on the right for pin definitions. Note the following when connecting the floppy cable: • The floppy disk drive cable has seven twisted wires. • A red mark on a wire typically designates the location of pin 1. A single floppy disk drive ribbon cable has 34 wires and two connectors to provide for two floppy disk drives.
Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC power cord before adding, changing or installing any hardware components. Before Power On 1. Make sure that the Standby PWR LED (LE1) is not lit.
X8ST3-F/X8STE User's Manual 2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A for details on beep codes.) 3. Remove all memory modules and turn on the system. (If the alarm is on, check the specs of memory modules, reset the memory or try a different one.) Memory Errors 1. Make sure that the DIMM modules are properly installed and fully seated in the slots. 2. You should be using unbuffered ECC or non-ECC DDR3 (1.5V) 1333/1066/800 MHz memory (recommended by the manufacturer).
Chapter 3: Troubleshooting com/support/bios/). Note: Not all BIOS can be flashed. Some cannot be flashed; it depends on the modifications to the boot block code. 3.
X8ST3-F/X8STE User's Manual BIOS warning message and the information on how to update your BIOS on our web site. Select your motherboard model and download the BIOS (.rom) file to your computer. Also, check the current BIOS revision and make sure that it is newer than your BIOS before downloading. You may choose the zip file or the .exe file. If you choose the zipped BIOS file, please unzip the BIOS file onto a bootable device or a USB pen/thumb drive. To flash the BIOS, run the batch file named "ami.
Chapter 3: Troubleshooting Question: Does X8 series motherboards come with a screw type CPU heat sink bracket? Answer: No, it does not come with a bracket for a screw-type heat sink. Customers have to purchase it separately. Please contact RMA for information, ask for part number BKT_0023L.
X8ST3-F/X8STE User's Manual Notes 3-6
Chapter 4: AMI BIOS Chapter 4 BIOS 4-1 Introduction This chapter describes the AMI BIOS Setup Utility for the X8ST3-F/X8STE. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens. Starting BIOS Setup Utility To enter the AMI BIOS Setup Utility screens, press the key while the system is booting up. Note: In most cases, the key is used to invoke the AMI BIOS setup screen.
X8ST3-F/X8STE User’s Manual How to Start the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the key to enter the main menu of the AMI BIOS Setup Utility. From the main menu, you can access the other setup screens. An AMI BIOS identification string is displayed at the left bottom corner of the screen, below the copyright message. Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Chapter 4: AMI BIOS System Overview: The following BIOS information will be displayed: System Time/System Date Use this option to change the system time and date. Highlight System Time or System Date using the arrow keys. Enter new values through the keyboard. Press the key or the arrow keys to move between fields. The date must be entered in Day MM/DD/YY format. The time is entered in HH:MM:SS format. (Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.
X8ST3-F/X8STE User’s Manual 4-3 Advanced Setup Configurations Use the arrow keys to select Boot Setup and hit to access the submenu items: BOOT Feature Quick Boot If Enabled, this option will skip certain tests during POST to reduce the time needed for system boot. The options are Enabled and Disabled. Quiet Boot This option allows the bootup screen options to be modified between POST messages or the OEM logo. Select Disabled to display the POST messages.
Chapter 4: AMI BIOS Wait For 'F1' If Error This forces the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled. Hit 'Del' Message Display This feature displays "Press DEL to run Setup" during POST. The options are Enabled and Disabled. Watch Dog Function If enabled, the Watch Dog Timer will allow the system to reboot when it is inactive for more than 5 minutes. The options are Enabled and Disabled.
X8ST3-F/X8STE User’s Manual ting. Select Auto for the BIOS to automatically select the CPU multiplier setting for your system. The options are Auto and Manual. Clock Spread Spectrum Select Enable to use the feature of Clock Spectrum, which will allow the BIOS to monitor and attempt to reduce the level of Electromagnetic Interference caused by the components whenever needed. Select Disabled to enhance system stability. The options are Disabled and Enabled.
Chapter 4: AMI BIOS Intel AES-NI (When supported by the CPU) Intel® AES instructions are a new set of instructions available beginning with the the all new 2010 Intel® Core™ processor family based on the 32nm Intel® microarchitecture. These instructions enable fast and secure data encryption and decryption, using the Advanced Encryption Standard (AES). The options are Disabled and Enabled.
X8ST3-F/X8STE User’s Manual C3 Auto Demotion When enabled, the CPU will conditionally demote C6 or C7 requests to C3 based on un-core auto-demote information. The options are Disabled and Enabled. ACPI T State This feature Enables the ACPI throttling support for the processor to save power. The options are Disabled and Enabled. DCA Technology This feature accelerates the performance of TOE devices.
Chapter 4: AMI BIOS L0s is intended as a power saving state. It allows a link to quickly enter and recover form a power saving state without going through recovery. L1 is a power saving state that allows an additional power saving over L0s, but with additional resume (wake-up) latency. Select Enabled to activate QPI power saving (L0s and L1 are automatically selected by the motherboard), select Disabled for normal operational state without any power-saving function. The options are Disabled and Enabled.
X8ST3-F/X8STE User’s Manual Throttling - Closed Loop Throttling improves reliability and reduces power in the processor by automatic voltage control during processor idle states. Available options are Disabled and Enabled. Intel VT-d Select Enabled to enable Intel's Virtualization Technology support for Direct I/O VT-d by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.
Chapter 4: AMI BIOS Legacy USB Support Select Enabled to use Legacy USB devices. If this item is set to Auto, Legacy USB support will be automatically enabled if a legacy USB device is installed on the motherboard, and vise versa. The settings are Disabled, Enabled and Auto.
X8ST3-F/X8STE User’s Manual activate the following submenu screen for detailed options of these items. Set the correct configurations accordingly. The items included in the submenu are: Type Select the type of device connected to the system. The options are Not Installed, Auto, CD/DVD and ARMD. LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive. In the LBA mode, the maximum drive capacity is 137 GB.
Chapter 4: AMI BIOS DMA Mode Select Auto to allow the BIOS to automatically detect IDE DMA mode when the IDE disk drive support cannot be determined. Select SWDMA0 to allow the BIOS to use Single Word DMA mode 0. It has a data transfer rate of 2.1 MB/s. Select SWDMA1 to allow the BIOS to use Single Word DMA mode 1. It has a data transfer rate of 4.2 MB/s. Select SWDMA2 to allow the BIOS to use Single Word DMA mode 2. It has a data transfer rate of 8.3 MB/s.
X8ST3-F/X8STE User’s Manual the S.M.A.R.T. Select Enabled to allow the AMI BIOS to use the S.M.A.R.T. to support hard drive disk. The options are Disabled, Enabled, and Auto. 32-Bit Data Transfer Select Enable to enable the function of 32-bit IDE data transfer. The options are Enabled and Disabled. PCI/PnP Configuration This feature allows the user to set the PCI/PnP configurations for the following items: Clear NVRAM This feature clears the NVRAM during system boot. The options are No and Yes.
Chapter 4: AMI BIOS Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM This feature is to enable LAN OPROM for PXE. This is to boot computers using a network interface. The options are Disabled and Enabled. Load SAS Option ROM (X8ST3-F Only) This feature is to load the Serial Attached SCSI (SAS) option ROM, if available. The options are Disabled and Enabled. Boot Graphics Adapter Priority Use this feature to select the graphics controller to be used as the primary boot device.
X8ST3-F/X8STE User’s Manual ditional option, Onboard IPMI is featured on the X8ST3-F motherboard only, and becomes the default. Serial Port Mode This feature allows the user to set the serial port mode for Console Redirection. The options are 115200 8, n 1; 57600 8, n, 1; 38400 8, n, 1; 19200 8, n, 1; and 9600 8, n, 1. Flow Control This feature allows the user to set the flow control for Console Redirection. The options are None, Hardware, and Software.
Chapter 4: AMI BIOS Warning: Any temperature that exceeds the CPU threshold temperature predefined by the CPU manufacturer may result in CPU overheat or system instability. When the CPU temperature reaches this predefined threshold, the CPU and system cooling fans will run at full speed.
X8ST3-F/X8STE User’s Manual speed to bring the CPU temperature down. If the CPU temperature still increases even with the CPU fan running at full speed, the system buzzer will activate and the Overheat LED will turn on. The Early Alarm – the Overheat LED and system buzzer will be activated exactly when the High level is reached. The CPU fan will run at full speed to bring the CPU temperature down. Note: In both the alarms above, please take immediate action as shown below.
Chapter 4: AMI BIOS system cooling. Select Full Speed to allow the onboard fans to run at full speed (of 100% Pulse Width Modulation Duty Cycle) for maximum cooling. The Full Speed setting is recommended for special system configuration or debugging. Select Performance for the onboard fans to run at 70% of the Initial PWM Cycle for better system cooling. The Performance setting is recommended for high-power-consuming and high-density systems.
X8ST3-F/X8STE User’s Manual APIC ACPI SCI IRQ When this item is set to Enabled, APIC ACPI SCI IRQ is supported by the system. The options are Enabled and Disabled. Headless Mode This feature is used to enable system to function without a keyboard, monitor or mouse attached The options are Enabled and Disabled. ACPI Version Features The options are ACPI v1.0, ACPI v2.0 and ACPI v3.0. Please refer to ACPI's website for further explanation: http://www.acpi.
Chapter 4: AMI BIOS Channel Number Status - This feature returns the channel status for the Channel Number selected above: "Channel Number is OK" or "Wrong Channel Number". IP Address Source - This feature selects whether the IP address, Subnet Mask and Gateway Address are automatically assigned by the network's DHCP server (Dynamic Host and Configuration Protocol) or manually entered by the user (Static). If Static is selected, the IP Address, Subnet Mask and Gateway Address must be manually entered below.
X8ST3-F/X8STE User’s Manual Clear event log This option clears the Event Log memory of all messages. The options are OK and Cancel. PCIE Error Log Use this option to enable logging of errors encountered in the system's PCIe bus. The options are Yes and No. Memory ECC Error Log Use this option to enable logging of errors encountered in the system's memory. The options are Yes and No.
Chapter 4: AMI BIOS 4-4 Security Settings The AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first. Supervisor Password This item indicates if a supervisor password has been entered for the system. Clear means such a password has not been used and Set means a supervisor password has been entered for the system. User Password: This item indicates if a user password has been entered for the system.
X8ST3-F/X8STE User’s Manual Clear User Password (Available only if User Password has been set) Password Check Available options are Setup and Always. Boot Sector Virus Protection When Enabled, the AMI BOIS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The options are Enabled and Disabled.
Chapter 4: AMI BIOS Hard Disk Drives This feature allows the user to specify the boot sequence from all available hard disk drives. The settings are Disabled and a list of all hard disk drives that have been detected (i.e., 1st Drive, 2nd Drive, 3rd Drive, etc). Removable Drives This feature allows the user to specify the boot sequence from available Removable Drives. The settings are 1st boot device, 2nd boot device, and Disabled.
X8ST3-F/X8STE User’s Manual figuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press . Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system configuration, and reboot the computer. Select Discard Changes and Exit from the Exit menu and press . Discard Changes Select this option and press to discard all the changes and return to the AMI BIOS Utility Program.
Appendix A: POST Error Beep Codes Appendix A POST Error Beep Codes This section lists POST (Power On Self Test) error beep codes for the AMI BIOS. POST error beep codes are divided into two categories: recoverable and terminal. This section lists Beep Codes for recoverable POST errors. Recoverable POST Error Beep Codes When a recoverable type of error occurs during POST, BIOS will display a POST code that describes the problem.
X8ST3-F/X8STE User's Manual Notes A-2
Appendix B: Installing the Windows OS Appendix B Installing the Windows OS After all hardware components have been installed, you must first configure Intel South Bridge RAID Settings before you install the Windows OS and other software drivers. To configure RAID settings, please refer to RAID Configuration User Guides posted on our website at www.supermicro.com/support/manuals. B-1 Installing the Windows OS for Systems with RAID Functions 1.
X8ST3-F/X8STE User's Manual Guide B-2 Installing the Windows OS for Systems without RAID Functions 1. Insert Microsoft's Windows XP/2003 Setup CD in the CD Driver, and the system will start booting up from CD. 2. Press the key when the message-" Press F6 if you need to install a third party SCSI or RAID driver" displays. 3. When the Windows XP/2003 Setup screen appears, press "S" to specify additional device(s). 4.
Appendix C: Software Installation Instructions Appendix C Software Installation Instructions C-1 Installing Drivers After you've installed the Windows Operating System, a screen as shown below will appear. You are ready to install software programs and drivers that have not yet been installed. To install these software programs and drivers, click the icons to the right of these items.
X8ST3-F/X8STE User's Manual C-2 Configuring Supero Doctor III The Supero Doctor III program is a Web-base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called the SD III Client. The Supero Doctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system.
Appendix C: Software Installation Instructions Supero Doctor III Interface Display Screen-II (Remote Control) Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/PRODUCT/ Manuals/SDIII/UserGuide.pdf. For Linux, we will still recommend that you use Supero Doctor II.
X8ST3-F/X8STE User's Manual Notes C-4
Appendix D: BIOS Recovery Appendix D - BIOS Recovery The recovery procedure described in this section is to be used only when advised by your Supermicro Technical Support representative, or in cases of emergencies where the system no longer can boot due to a corrupted BIOS. DO NOT re-program (re-flash) the BIOS if your system is running properly.
X8ST3-F/X8STE User’s Manual 5. When the Boot Sector Recovery Process is complete, the system will reboot automatically and you will see a checksum error on your screen. Part 2 - BIOS Reprogramming (Re-Flashing) After completing the Boot Sector Recovery Process, you will need to reprogram (“re-flash”) the proper BIOS binary file again into the BIOS ROM in order to have the correct BIOS file loaded by the system.
(Disclaimer Continued) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
