Product Brochure

ManualsBrandsSuperstrut ManualsElectrical1-1/4 in. Universal Pipe Clamp Gold Galvanized (10-Piece per Case)

In This Section…

Metal Framing, Pipe Hangers and Accessories

D-1

Superstrut

Metal Framing, Pipe Hangers and Accessories

Metal Framing Channels — Overview.............................D-2–D-7

Threaded Products and Hardware.................................D-8–D-13

Fittings and Brackets ..................................................D-14–D-21

Concrete Inserts..........................................................D-22–D-23

Beam Clamps .............................................................D-24–D-32

Pipe Straps, Conduit Clamps and Hangers ..................D-33–D-79

Surface Raceway and Lighting Systems .....................D-80–D-84

Special Metals ............................................................D-85–D-94

Slotted Angle Metal Framing .......................................D-95–D-96

Metal Framing Engineering Data...............................D-97–D-119

Summary of content (118 pages)

PAGE 1
In This Section… Superstrut ® Metal Framing, Pipe Hangers and Accessories Metal Framing Channels — Overview.............................D-2–D-7 Threaded Products and Hardware.................................D-8–D-13 Fittings and Brackets ..................................................D-14–D-21 Concrete Inserts..........................................................D-22–D-23 Beam Clamps .............................................................D-24–D-32 Pipe Straps, Conduit Clamps and Hangers ......
PAGE 2
Metal Framing, Pipe Hangers and Accessories Metal Framing Channels — Overview New Trivalent Galv-Krom® Finish Is RoHS Compliant Thomas & Betts is proud to introduce the new and improved Trivalent Galv-Krom® finish. Galv-Krom® finish is a combination of .5 mils electro-plated Zinc and a gold Trivalent Chromium finish.
PAGE 3
Metal Framing Channels — Overview Finishes GoldGalv® Copper Plated (“T” inserted as the second digit of the part number; Example: CTL-710-2) Plain steel proceeds through a series of rinse tanks to clean the material surface. Once cleaned, the fabricated part is etched by dipping into an acid pickle bath to prepare the surface for adhesion. Copper is electrically applied by submerging in a copper bath. To seal the finish, the product continues to a sealer tank and is then dried by forced hot air.
PAGE 4
Metal Framing Channels — Overview Finishes (continued) Metal Framing, Pipe Hangers and Accessories GoldGalv ® D-4 The standard GoldGalv® finish is made up of a multi-step electrogalvanizing and zinc dichromate process. The trivalent Chromium finish is applied over the zinc, producing a chemically bonded non-porous barrier for protection from moisture and air. The .
PAGE 5
Metal Framing Channels — Overview Finishes (continued) SilverGalv® Electro-Galvanized Finish From Superstrut® Protection is the name of the game and SilverGalv® delivers a winning combination of features designed to meet the most exacting specifications.
PAGE 6
Metal Framing Channels — Overview 15⁄8 7 ⁄8 Metal Framing, Pipe Hangers and Accessories 9 ⁄8 3 ⁄32 1 5⁄8 7 ⁄8 1 5⁄8 ⁄32 9 ⁄32 9 1 3⁄8 13 ⁄16 12 ga A-1200 B-1200 C-1200 Channel available in Solid, Half Slot, Punched, Slotted and Knockout configurations. Wt./Ft. 1.90 lbs. Channel available in Solid, Half Slot, Punched and Slotted configurations. Wt./Ft. 1.28 lbs. Channel available in Solid, Half Slot and Punched configurations. Wt./Ft. 1.70 lbs.
PAGE 7
Metal Framing Channels — Overview Hole Configurations Superstrut® Channels — Welding Combinations 2" Half Slot Channel All Superstrut® Channels are available in a variety of combinations — some are shown here. DIM. (IN.) GA. STD. CTN. 15⁄ 8 x 15⁄ 8 15⁄ 8 x 13⁄ 16 15⁄ 8 x 13⁄ 8 15⁄ 8 x 27⁄ 16 15⁄ 8 x 31⁄ 4 15⁄ 8 x 15⁄ 8 15⁄ 8 x 13⁄ 16 12 12 12 12 12 14 14 * * 500 500 * * 500 ⁄16" x 1 1⁄ 8" slots on 2" centers. 9 2* 2-A 2-B * Standard lengths 10 ft. and 20 ft. for standard cartons.
PAGE 8
Threaded Products & Hardware Metal Framing, Pipe Hangers and Accessories Trapnut ® Strut Fastener Features and Benefits The unique scissor action of the Trapnut® Strut Fastener closes at any desired position on the threaded rod. Once closed, precision threads trap the threaded rod for a sturdy hold that can be adjusted up or down for fine-tune positioning. While the versatile Trapnut has a locking pin that holds it in the desired position, it can also be removed and reused.
PAGE 9
Threaded Products & Hardware Handle Retro-Fit Trapeze Applications with Ease! Trap-Eze™ Connector Easily installs above existing trapeze. • Easily installs above or to the side of an existing assembly, eliminating the need to disassemble and reassemble the trapeze Can be used to extend existing trapeze. • Connectors can be reused upon disassembly of a trapeze Designed for use with the innovative Trapnut® Strut Fastener.
PAGE 10
Threaded Products & Hardware Channel Nuts UC-100 Universal Cone Nut Metal Framing, Pipe Hangers and Accessories Superstrut® channel nuts are manufactured from mild steel and are case hardened. D-10 Design Data Superstrut® self-aligning channel nuts are designed to provide resistance to pull out and resistance to side slip in excess of the full strength of the channels with which they are used.
PAGE 11
Threaded Products & Hardware Nuts & Bolts A-100 Regular Spring Nut E-142 Hex Head Cap Screw E-150-S Lag Bolt Screw Sizes: 1⁄ 4", 5⁄ 16", 3⁄ 8", 1⁄ 2", 5 ⁄ 8", 3⁄ 4" & 7⁄ 8" Sizes: 1⁄ 4" x 1", 1⁄ 4" x 11⁄ 2", 3 ⁄ 8" x 1", 3⁄ 8" x 11⁄ 2", 1⁄ 2" x 15⁄ 16" & 1⁄ 2" x 11⁄ 2" Size: 3⁄ 8" & 1⁄ 2" Nut is square over 1⁄2" size. See price sheet for additional sizes.
PAGE 12
Threaded Products & Hardware Nuts & Bolts (continued) Metal Framing, Pipe Hangers and Accessories Fender Washer CAT. NO. EF-147 EF147 1/4 EF-147-3/8 EF-147-1/2 Regular Spring Stud Nut SIZE (IN.) DIA. (IN.) ⁄4 ⁄8 1 ⁄4 11⁄ 4 11 ⁄ 2 2 1 3 HOLE STD. (IN.) STD. CTN. ⁄ 16 ⁄ 16 9 ⁄ 16 100 100 100 5 7 A-182 to A-185 Springless Stud Nut A A-177 to A-180 CAT. NO. BOLT DIA. (IN.) LENGTH A (IN.) STD. CTN.
PAGE 13
Threaded Products & Hardware Threaded Rod E-151 — Coach Screw Rod H-104 — Hanger Rod: Continuous Thread H-104 Series Rod E-151 • Black available upon request CAT. NO. • Machine-threaded opposite end, carbon steel STANDARD ROD LENGTHS STD. CTN. ⁄8 ⁄2 4, 6, 8, 10, 12 4, 6, 8, 10 100 100 3 1 DESIGN LOAD LBS. STD. CTN. ⁄4 ⁄8 1 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 20 16 13 11 10 9 8 150 610 1,130 1,810 2,710 3,770 4,960 * * * * * * * 1 3 Black available upon request. *Standard lengths 6 ft., 10 ft. and 12 ft.
PAGE 14
Fittings & Brackets Fittings & Brackets — Series 200 Metal Framing, Pipe Hangers and Accessories Material Design Data Superstrut fittings and brackets are manufactured from hot rolled carbon steel. Ratings vary when used with 12 or 14 gauge channel and are shown for each channel material. ® GoldGalv® hardware finish is standard for all Superstrut® products.
PAGE 15
Fittings & Brackets 17⁄ 16" 4 1⁄ 8" 4 1⁄ 8" 5 3⁄8" 17⁄ 8" 1 ⁄ 16" 7 5 ⁄8" 3 A AB-242 For use with either 3⁄8" or 1⁄2" hanger rod AB252 CAT. NO. A (IN.) STD. CTN.
PAGE 16
Fittings & Brackets Z Shape Fittings 15⁄ 8" 13 13 ⁄ 8" 11⁄ 16" ⁄ 16" 1 ⁄ 16" Metal Framing, Pipe Hangers and Accessories 1 11⁄ 16" 21⁄ 8" 21⁄ 8" A209 For attaching “A” series channel. 21⁄ 8" B209 For attaching “B” series channel. C209 For attaching “C” series channel. 3 1⁄ 4" . . . . . . Standard Dimensions . . . . . . • • • • • 2 7⁄ 16" 17⁄ 8" 17⁄ 8" CZ209 For attaching “A” back to back. Standard Finish – GoldGalv®, unless otherwise stated. EZ209 For attaching “E” series channel.
PAGE 17
Fittings & Brackets U Shape Fittings 5c" 5 3⁄ 8" 5 3⁄ 8" 121⁄ 32" 3 1⁄ 4" 7 1⁄ 4" 3 ⁄ 16" 5 3⁄ 8" 121⁄ 32" 5 ⁄ 8" 11e" A210 For attaching “A" series channel A208 Does not include strut nut or bolts. For “A” series channel. A211 For attaching “A" series channel. 2 1 ⁄ 2" 7" 39⁄ 32" 11⁄ 16" 11⁄ 2" 15⁄ 8" 1" 121⁄ 32" 10 ga.
PAGE 18
Fittings & Brackets Post Bases Metal Framing, Pipe Hangers and Accessories 15⁄8" 111⁄16" 4 Holes 3 ⁄4" Dia. 15⁄8" 4 Holes 3 ⁄4" Dia. 1 ⁄16" 31⁄4" 33⁄8" 1 ⁄8" 41⁄2" 31⁄2" 6" 41⁄2" 5 41⁄2" 6" 15⁄8" 31⁄2" 11 4 Holes 3 ⁄4" Dia. 15⁄8" 6" 4 Holes 3 ⁄4" Dia. 6" AP-231 41⁄2" 6" AP-234 AP-232 2 Holes ⁄4" Dia. 15⁄8" 3 15⁄8" AP-235 15⁄8" 111⁄16" 2 Holes 3 ⁄4" Dia. 2 Holes ⁄4" Dia. 111⁄16" 6" 15⁄8" 2 Holes ⁄4" Dia.
PAGE 19
Fittings & Brackets Special Application Fittings 4" 21⁄8" Q202 Q205 2 3⁄4" 23⁄4" 3 ⁄8" 5 35⁄8" 6" 6" 53⁄8" 27⁄16" 3 27⁄16" 5 ⁄8" 113⁄16" 113⁄16" Q255 For 2" standard pipe. Load 1,500 lbs. Q256 For 2" standard pipe. Load 1,500 lbs. Q253 Q254 For 11⁄ 4" standard pipe. Load 1,500 lbs. 31⁄2" Metal Framing, Pipe Hangers and Accessories 4" 21⁄8" . . . . . . . . . . . . . . . Standard Dimensions . . . . . . . . . . . . . . .
PAGE 20
Fittings & Brackets Special Application Fittings (continued) 81⁄2" 43⁄8" 101⁄2" 6 ⁄8" Metal Framing, Pipe Hangers and Accessories 1 33⁄4" ⁄16" 13 2" 4" 4" A 15⁄8" 1 ⁄8" 5 B ⁄16" 13 ⁄16" 13 A 1" C S205 Design Uniform Load/lbs. A-1,200 650 A-1,400 500 S204 Design Uniform Load/lbs. A-1,200 650 A-1,400 500 AN-270 2" 31⁄4" C 121⁄2" 31⁄4" 31⁄8" B 33⁄4" ⁄16" Dia. 7 6" ⁄32" Dia. 9 S-201-L and R R as shown — L opposite hand. 12 ga. steel. Design Uniform Load/lbs.
PAGE 21
Fittings & Brackets Brackets 161⁄2" 51⁄4" 13⁄ 16" 31⁄8" 51⁄4" 31⁄8" 13⁄16" 181⁄2" 71⁄4" 201⁄2" 31⁄8" 73⁄4" 6" 1 ⁄16" 3 1 ⁄16" 3 6" 6" 13⁄16" 15⁄8" 1 ⁄8" 5 1 ⁄8" 5 43⁄4 Metal Framing, Pipe Hangers and Accessories S236 Design Uniform Load/lbs. A-1,200 800 A-1,400 650 S226 Design Uniform Load/lbs. A-1,200 1,000 A-1,400 750 S222 Design Uniform Load/lbs. A-1,200 1,000 A-1,400 750 43⁄4" 71⁄2" 57⁄ 8" S248 Design Moment (channel upright as shown) When supported by A-1,200 10,800 inch lbs.
PAGE 22
Concrete Inserts Concrete Inserts (Series 300/400) Metal Framing, Pipe Hangers and Accessories Standard lengths 10 ft. and 20 ft. length tolerance 3⁄16". Assemblies available in any length from 12" to 20 ft. Consult factory. Insert with end caps and foam filler strip installed. Material: B-302 and C-302 Insert Channel-12 ga. steel. B-804 and C-804 End Caps — 12 ga. steel. Superstrut® continuous insert channel is cold formed from 12 gauge hot-rolled strip steel in two basic sizes as follows: 4" CAT. NO.
PAGE 23
Concrete Inserts 450 — End Cap CAT. NO. FOR CHANNEL X (IN.) MATERIAL STD. CTN. C-450TB C-1,200 3 12 ga. 100 x Does not come in pairs, order number of total pieces required. Inserts may be assembled from short pieces of channel by use of end caps. 450 Order closure strip separately. 317⁄32" • An insert with a knockout saves covering the opening. Accommodates hanger rod sizes from 1⁄4" through 7⁄8" by means of an AB-102 insert nut 2" 15⁄8" 13⁄8" • Design load: 1,350 lbs. in 3,000 lb.
PAGE 24
Beam Clamps Superstrut® Beam Clamps Metal Framing, Pipe Hangers and Accessories Materials Most products are manufactured from hot-rolled carbon steel bars or hot-rolled strip steel. Pipe rollers are cast iron. Products which are copper placed carry the letter “T” in the prefix. Design Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the “AMERICAN STANDARD CODE FOR PRESSURE PIPING.” GoldGalv® hardware finish is standard for all Superstrut® products.
PAGE 25
Beam Clamps Beam Clamps for Mounting Channel (continued) 1 1⁄4" 3" 1 1⁄4" 7 3 ⁄8" 1 Hole 9 ⁄16" Dia. ⁄8" 1 ⁄8" U515 For all “A” series channel. 1 ⁄2" x 1 1⁄2" set screw included. Design load 800 lbs. U514A ⁄8" x 1 1⁄2" set screw included. Design load 1,650 lbs./per pair. U514 ⁄8" x 1 1⁄2" set screw included. Design load 750 lbs./per pair. 3 U543 2 1⁄8" Wide Flange Beam 1 3⁄4" A-1200 Channel 3 1⁄2" 1 1⁄4" 3 1⁄2" U515B For all "B" series channel. 1 ⁄2" x 1 1⁄2" set screw included.
PAGE 26
Beam Clamps Metal Framing, Pipe Hangers and Accessories Beam Clamps for Hanging Rod 11⁄4" Beam Clamps — Malleable Iron, Silver Electroplated Finish 2 5⁄8" ⁄8" 7 2 7⁄8" 500SS316, 502SS316 and 503SS316 in 316 Stainless Steel, also available. CAT. NO. 500-SC 501 502 503-SC 507 508 509 510 511-SC BASE SIZE JAW (IN.) OPENING A B (IN.) 1 11 ⁄ 2 2 2 5⁄ 8 2 1⁄ 2 2 1⁄2 1 2 7 ⁄ 32 2 7 ⁄ 32 11⁄ 4 15⁄ 8 2 21⁄ 2 23⁄ 8 2 3⁄ 8 11⁄ 4 11⁄ 8 11⁄ 8 Square nut, order separately.
PAGE 27
Beam Clamps Beam Clamps for Hanging Rod (continued) Coach Screw U577 Clevis & Swing Connector Rod Size 1⁄2" Standard Finish – GoldGalv® brand For use with wood beam. "C" Set Screw Included U-560 — Heavy-Duty Beam Clamp CAT. NO. A U560 1/4 U-560-3/8 U-560-1/2 U-560-5/8 1 DIMENSIONS (IN.) B C ⁄4 3 ⁄8 1 ⁄2 5 ⁄8 ⁄8 1 ⁄8 1 ⁄4 1 ⁄4 ⁄ 8 x 11⁄ 2 3 ⁄ 8 x 11⁄ 2 1 ⁄ 2 x 11⁄ 2 1 ⁄ 2 x 11⁄ 2 1 3 DESIGN LOAD LBS. STD. CTN.
PAGE 28
Beam Clamps Beam Clamps for Hanging Rod B Metal Framing, Pipe Hangers and Accessories E-233 — Anchor Clip A • Clamps to I-beams, channels, angles and column C • Two sizes are available, one for 3⁄8 inch and the other for 1⁄2 inch hanger rod. Each takes flanges up to .8 inch thickness For use with E-231 and E-232 clamps when hanger rod is not in straight through position. E-231 — Structural Steel Clamp CAT. NO. A A DIMENSIONS (IN.) B C WT. LBS.
PAGE 29
Beam Clamps Beam Clamps for Hanging Rod (continued) E-160 — Adjustable Beam Clamp • Clamps to I-beam where edge of beam flange does not exceed .8 inch thickness • Hook rod is furnished in three lengths to fit beam flanges up to 6, 9 or 12 inch widths CAT. NO. 1 ⁄2" HANGER RODS BEAM FLANGE WIDTH (IN.) WT. LBS./C 8, 11 or 14 ⁄2 1 1 ⁄ 2" Rod 21⁄ 2 to 6 51⁄ 2 to 9 81⁄ 2 to 12 115 125 154 3 Min. 3 5⁄8 Max. 2 ⁄8 1 Load rating 800 lbs. with a safety factor of three.
PAGE 30
Beam Clamps Metal Framing, Pipe Hangers and Accessories Beam Clamps for Hanging Rod C-777 — Steel Top Beam Clamp & C-778 — Steel Wide JawTop Beam Clamp M-777 — Steel Top Beam Clamp • Junior Top Beam C-Clamp • Standard finish is Gold-Galv® • Available in Electro-Galvanized (EG) or Black (B) Malleable Iron B A • Provides clamping under roof installations with bar joist construction. Max. joist thickness 5⁄8" D E • Order by Cat. No., rod size C M-777 ROD SIZE A (IN.) DESIGN LOAD LBS.
PAGE 31
Beam Clamps Beam Clamps for Mounting Pipe and Conduit C-247, C-248 & C-249 — Steel Conduit Clamps Pipe Supports Three types of pipe clamps are available to provide right angle, vertical and parallel attachment to a beam. Types RC, EC and PC are malleable iron clamps with an edge that grips the structural member for maximum holding power when tightened. Type RCS clamps are all steel, providing two bearing surfaces for strong attachment for mounting pipe or conduit at right angles to the beam.
PAGE 32
Beam Clamps Metal Framing, Pipe Hangers and Accessories Conduit and Pipe Hangers 6H Series Conduit and Pipe Hanger • Accommodates 1⁄2" through 4" EMT or rigid conduit 6H Series Without bolt Fig. 1 6H-B Series With bolt and hex nut Fig. 2 • Can be used for either vertical or horizontal installation • 6HTB Series have a built-in nut so there are less parts to handle or drop • Installs easily with a screwdriver 6H- T Threaded Series Threaded without bolt Fig.
PAGE 33
Pipe Straps, Conduit Clamps & Hangers Excellent Corrosion Resistance and a Superior Paint Base GoldGalv® hardware finish is standard for all Superstrut® products. This is a multi-process finish of electro-plated zinc, followed by gold-colorized zinc dichromate to give excellent corrosion resistance and a superior paint base. See page D-3 for a complete description of the GoldGalv® hardware finish. GoldGalv® hardware will be furnished if no other finish is specified.
PAGE 34
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Superstrut® Pipe Straps Pre-Assembled for Easy Handling and Sorting Superstrut® Pipe Straps are designed to be twist inserted anywhere along the slot side of the channel. Pipes can be placed as closely as pipe couplings permit.
PAGE 35
Pipe Straps, Conduit Clamps & Hangers Superstrut® Pipe Straps (continued) 701 — Superstrut® Straps for O.D. Tubing (continued) 702 — Superstrut® Straps for Rigid Conduit, IMC and Pipe • For Rigid or IMC Conduit, Pipe and Electric Metal Tubing (EMT) RIGID CONDUIT OR CAT. NO. PIPE SIZE (IN.) O.D. SIZE (IN.) STEEL STRAP THICKNESS DESIGN LOAD (LBS.) STD. CTN.
PAGE 36
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Cobra® One-Piece Cable and Pipe Clamp Takes a bite out of your installation time! • One-piece, heavy-duty construction ready to install right out of the box, no need to break apart and re-assemble, no screws or bolts to drop • Installs quickly and securely using one hand Accepts… • Universal bolt head accepts a range of tools Multi-driver combination bolt head accepts a wrench, screwdriver or nut driver.
PAGE 37
Pipe Straps, Conduit Clamps & Hangers Angled for Easy Tightening! Angler ® Pipe and Conduit Clamp ® Pipe and Conduit Clamp For Rigid Conduit and Standard Pipe Universal Series CAT. NO. Rigid Series STRAP DESIGN INSTALL TORQUE SIZE (IN.) THICKNESS LOAD (LBS.) (IN. LBS.) STD. CTN.
PAGE 38
Pipe Straps, Conduit Clamps & Hangers Pipe Straps Metal Framing, Pipe Hangers and Accessories A-716 — Snap•Guard® Cushioned Clamp Tube Series P-716 — Pipe Series O.D. TUBING SIZES TUBE O.D. (IN.) ASSEMBLY CAT. NO. STANDARD PIPE SIZES NOMINAL PIPE SIZE (IN.) ASSEMBLY CAT. NO. STD. CTN. Standard Finishes – GoldGalv® brand. Available in Stainless Steel — use SS suffix. (i.e) A-716-1SS, Electro-Galvanized (Silver) — use EG suffix. (i.
PAGE 39
Pipe Straps, Conduit Clamps & Hangers Pipe Straps (continued) C-716 — Isolator for Copper Tubing Features: Designed for use with Superstrut® channel and pipe straps and Superstrut® C-711 Hangers, and may also be used with all standard flatbar or malleable iron hangers. AA Materials: Application: To provide a means to effectively isolate copper tubing from its supports to prevent the transmission of sound and vibration. NOMINAL PIPE SIZE (IN.) HANGER, C-711 OR PIPE STRAP, 702 WIDTH A (IN.) STD. CTN.
PAGE 40
Pipe Straps, Conduit Clamps & Hangers CB118 — Counter Bed Metal Framing, Pipe Hangers and Accessories Cable Clamps CB118 Counter Bed CAT. NO. CX118-081EG CH118 Counter Bed CH118 and CX118 Heavy-Duty Cable Clamp CAT. NO. CH118-055EG CH118-081EG CH118-110EG CH118-125EG CH118-135EG CH118-175PG CH118-205EG CH118-250EG CH118-300EG CH118-375EG CH118-425EG CH118-475EG CX118-081EG CX118-110EG CX118-125EG CX118-135EG CX118-175PG CX118-205EG STD. CTN. FIG. NO.
PAGE 41
Pipe Straps, Conduit Clamps & Hangers Cable Clamps (continued) C-755 — TPE C-755 — Porcelain Cable Clamps Hole Size A C-755 HOLE SIZE (IN.) A (IN.) STD. CTN.
PAGE 42
Pipe Straps, Conduit Clamps & Hangers Pipe Clamps Metal Framing, Pipe Hangers and Accessories HS Series Two-Hole Pipe Strap C-720, C-720SS — Extension Riser Clamp Designed for the support or steadying of vertical pipe risers. It is made of carbon steel and is designed to hold tight to the pipe, transmitting the load to the structure through the ears on each end. When possible, the clamp should be placed under a coupling, hub or lugs welded to the pipe. CAT. NO.
PAGE 43
Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) CX-725 — Extended Offset Pipe Clamp The Offset Pipe Clamp is used on pipe lines running at a fixed distance from a wall or floor. The standard clearance is two inches from the O.D. of pipe to the face of the surface. Non-standard clearances can be fabricated upon request. Designed to attach directly to piping where the exact distance between the structure and the pipe cannot be determined until the piping is in place.
PAGE 44
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Pipe Clamps (continued) CT-720 — Copper Riser Clamp C-724 — Ductile Iron Pipe Clamp Normally used for the support of uninsulated vertical tubing where no movement will occur. Please use C-720 for carbon steel piping or C-720P for plastic coating requirements. NOTE: This product is not designed to be supported with rods. Install using the maximum suggested torque values shown in the Technical Section of this catalog.
PAGE 45
Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) C-725 — Two-Bolt Pipe Clamp Designed to suspend cold or hot pipe lines where little or no insulation is required. The C-725 is usually used with an E-120-A Weldless Eyenut or E-157 Welded Eyerod. See Figure 298 heavy-duty Two-Bolt Clamp when higher loads are required. We will also design to meet special requirements such as special pipe sizes. C F E D Rated Loads are for up to 750°F (399°C). Material: Carbon Steel.
PAGE 46
Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) Metal Framing, Pipe Hangers and Accessories C-726 — Three-Bolt Pipe Clamp Designed for hot-insulated pipe lines up to 750°F. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. We will also design to meet special requirements such as special pipe sizes. Rated Loads are for up to 750°F (399°C). Material: Carbon Steel.
PAGE 47
Pipe Straps, Conduit Clamps & Hangers Pipe Clamps — A-726, Alloy Three-Bolt Pipe Clamp C F Designed for hot-insulated pipelines. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. D E Temperature range: above 750°F (399°C) to 1050°F (566°C). Material: Chrome Molybdenum Steel, ASTM A-387 Grade 22. Finish: Compliance: Federal Specification A-A-1192A Type 3, MSS-SP-69 Type 3 and BSPSS-BS3974.
PAGE 48
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Pipe Hangers (continued) CL-710 — Light-Duty Clevis Hanger CTL-710 — Copper Clevis Hanger Designed to support non-insulated, stationary lines from above, allowing for approximately 1" to 11⁄2" of vertical adjustment after the pipe is in place.
PAGE 49
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) ETL-710 — Light-Duty Clevis Hanger A F B C C L OF PIPE ETL-710 — Light-Duty Clevis Hanger CAT. NO. ETL710 1/2 ETL-710-3/4 ETL-710-1 ETL-710-1-1/4 ETL-710-1-1/2 ETL-710-2 ETL-710-2-1/2 ETL-710-3 ETL-710-3-1/2 ETL-710-4 ETL-710-5 ETL-710-6 TUBING SIZE (IN.) MATERIAL SIZE A B DIMENSIONS (IN.) C E F STD. CTN.
PAGE 50
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Pipe Hangers (continued) CI-710 — Clevis Hanger for Ductile Iron and A.W.W.A. Cast Iron Pipe Designed to support non-insulated, stationary ductile iron and A.W.W.A. cast iron lines from above, allowing for approximately 1" to 11⁄2" of vertical adjustment after the pipe is in place. The lower nut (not furnished) adjusts the pipe line to the proper elevation.
PAGE 51
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) C-711 — J Pipe Hanger Standard Finish – GoldGalv® brand Complies with Specification MSS SP 58, Type 5. Sizes through 5" conform to Ca. Code Title 24, Div. T22 for seismic restraint bracing. C-711F — Felt-Lined J Pipe Hanger Standard Metal Framing, Pipe Hangers and Accessories Standard Finish – GoldGalv® brand Available in sizes up to 8".
PAGE 52
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) A Metal Framing, Pipe Hangers and Accessories C-727 — Adjustable Swivel Ring Designed for the support of non-insulated static pipe lines. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. Compliance: Federal Specification A-A-1192A Type 10, MSS SP-69 Type 10, UL Listed and FM Approved ( 3⁄4" through 8").
PAGE 53
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) C-727-NFPA — NFPA Swivel Ring Designed for the support of non-insulated static pipe lines and to protect the pipe from coming into direct contact with the hanger by having the contact surface PVC coated. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. Designed for the support of non-insulated static pipe lines.
PAGE 54
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) Metal Framing, Pipe Hangers and Accessories CT-727 — Copper Tubing Swivel Ring Designed for the support of non-insulated static copper tubing lines. The swivel nut is knurled to provide a gripping surface when adjusting the tubing elevation. Compliance: Federal Specification A-A-1192A Type 10, MSS SP-69 Type 10.
PAGE 55
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) M-718, M-718-B — Extension Ring Hanger M-718 — (Rod Tapped – Electro-Galvanized) M-718-B — (Rod Tapped – Plain Finish) This split ring hanger is designed for the support of non-insulated stationary pipe lines. Also available in a two-screw design. The MT-742-R Ceiling Plate is normally used with this product. Malleable Iron. Finish: Standard Finish – EG (silver), Black (add suffix “-B”), Electro-Galvanized (add suffix “-EG”).
PAGE 56
Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) Seismic Bracing Metal Framing, Pipe Hangers and Accessories (Consult Superstrut® Seismic Hanger bulletin for additional information.) 15⁄8" 15⁄8" 15⁄8" 2 3⁄8" 23⁄8" 1 ⁄4" 3 11 ⁄16" Dia. 2 Holes ⁄16" Dia. 9 41⁄2" 15 4 ⁄2" 1 41⁄2" ⁄4" 1 1 ⁄4" 1 ⁄4" 2 Holes 9 ⁄16" Dia. 1 ⁄8" 5 15⁄8" 9 C749N 7/8 Seismic Brace 1,650 lb. load safety factor 3 C749N 5/8 Seismic Brace 1,650 lb. load safety factor 3 C749N Seismic Brace 1,500 lb.
PAGE 57
Pipe Straps, Conduit Clamps & Hangers PG-794 — Pipe Alignment Guide Designed to maintain the axial alignment of piping as it expands and contracts during operation. It is most typically installed adjacent to expansion joints and at reasonable distances between the expansion joint and the anchor point. Our Figures 1007 and 1010 also offer alternative means for your piping alignment needs. A B I NOTE: Guides are not designed to carry dead weight loads. Maximum temperature is 750°F.
PAGE 58
Pipe Straps, Conduit Clamps & Hangers Structure Attachments Metal Framing, Pipe Hangers and Accessories M-742-R, M-742-RB, MT-742-R – Single Plate A M-742-R — (Rod Tapped – Electro-Galvanized) M-742-RB — (Rod Tapped – Plain Finish) MT-742-R — (Rod Tapped – Copper Finish) B Designed for attaching a rod to a wooden member. This part is normally used in conjunction with our M-718 Split Ring. Material: Malleable Iron. M-742-R is Carbon Steel. Tap Ordering: Specify rod size and catalog number.
PAGE 59
Pipe Straps, Conduit Clamps & Hangers Structure Attachments (continued) C-736 — Light Welded Steel Bracket Designed to support up to 6" pipe. This bracket is for installation to walls as shown or inverted, and may require a backing plate. Holes for up to 3 ⁄4" rods are located at each end of the bracket to allow for use in either orientation. The C-736 Side Clip Steel Bracket Clip can be attached to the C-736 to support piping 31⁄2" or smaller. Please see the Figure 79 for more information.
PAGE 60
Pipe Straps, Conduit Clamps & Hangers PG-795 — Pipe Block 3" Standard Finish — Black (B). ⁄8" 7 1 ⁄2" Metal Framing, Pipe Hangers and Accessories 1 ⁄16" Dia. 7 Pipe Attachments H-115, H-115SS — Standard U-Bolt Our standard U-Bolts are recommended for use as supports or guides for piping. They are supplied with four hex nuts. The H-115SS is recommended for support of stainless steel piping. Please specify the grade of stainless steel you require when ordering.
PAGE 61
Pipe Straps, Conduit Clamps & Hangers Beam Attachments M-750 — Side Beam Bracket G Designed for bolted connections. Compliance: A-A-1192A Type 34 and MSS-SP 69 Type 34. Material: Malleable Iron (Maximum Temperature 450°F / 232°C). Finish: Standard Finish – GoldGalv®, Black (add suffix “-B”), Electro-Galvanized (add suffix “-EG”). Ordering: Specify rod size and catalog number. M-750-3/8 M-750-1/2 M-750-5/8 MAX. LOAD (LBS.
PAGE 62
Pipe Straps, Conduit Clamps & Hangers Metal Framing, Pipe Hangers and Accessories Rods and Rod Attachments F-112 — Turnbuckle M-129 — Extension Piece Used to connect right- and left-hand threaded rods together and provide for adjustment. Designed for attaching rods to the M-732-EXT Clamp and similar types of attachments. Material: Material: Forged Steel. Compliance: Federal Specification A-A-1192A Type 30, MSS-SP-69 Type 30 when used with a Figure 82.
PAGE 63
Pipe Straps, Conduit Clamps & Hangers Structure Attachments C-780 W/OB, C-780 W/HWB — Welded Beam Attachment Recommended for attachment to the bottom of beams when little or no pipe movement is expected. C-780 W/HWB is recommended for attachment to the bottom of beams, when pipe movement is expected. A bolt and nut or pin is supplied. A pin with cotters is normally supplied for rod sizes over 1". S E C Material: Carbon Steel.
PAGE 64
Pipe Straps, Conduit Clamps & Hangers Beam Clamps Metal Framing, Pipe Hangers and Accessories C-755 — Beam Clamp D-64 Designed to attach to the bottom of flanged beams. Normally used with the E-157 Eye Rod or E-120-A Eye Nut. Material: Carbon Steel. Compliance: Federal Specification A-A-1192A Type 21, MSS-SP-69 Type 21. Finish: Standard Finish – GoldGalv®, Black (add suffix “-B”), ElectroGalvanized (add suffix “-EG”), Thermoplastic (add suffix “-TP”).
PAGE 65
Pipe Straps, Conduit Clamps & Hangers Beam Clamps (continued) Beam Flange Width M-732-H — Steel Beam Clamp with Weldless Eyenut The M-732-H beam clamp with eyenut is used when welding to the structure is prohibited for supports where some movement is expected. The clamping effect is produced by the “ice-tong” action of the arms and is locked in place by the through bolt located just under the beam flange. E Material: Carbon Steel with Forged Steel Eyenut.
PAGE 66
Pipe Straps, Conduit Clamps & Hangers Beam Clamps (continued) Metal Framing, Pipe Hangers and Accessories M-732-EXT — Adjustable Beam Clamp D-66 Designed to attach to the bottom of flanged beams without requiring welding. Normally used with the M-129 Extension Piece (not furnished) up to a maximum 7⁄ 8" (M20) rod diameter. Loading is achieved through the clamp jaws while locking is accomplished by tightening the through-bolt located directly below the flange. Maximum flange thickness is 0.60 inches.
PAGE 67
Pipe Straps, Conduit Clamps & Hangers Rollers, Shields and Saddles C-728 — Pipe Roller (Pair) C728H — Pipe Roller Assembly (Pair) Cast aluminum roller, steel brackets. Order separately for each pair of rollers: • Cast aluminum rollers, steel brackets Two 1⁄2" x 5⁄16" hex head cap screws Two 1⁄2" channel nuts • Designed for standard saddles Adjustable to fit O.D. pipe 6" through 18". • Space to fit O.D. of pipe and wrapping A • Adjustable for radius up to 8" B 2-12⁄2"⁄ " 1 A 2 B CAT. NO. CAT.
PAGE 68
Pipe Straps, Conduit Clamps & Hangers Pipe Rolls Metal Framing, Pipe Hangers and Accessories C-729 — Harvard Roll Hanger A Designed to support piping lines from above, allowing for vertical adjustment and axial movement in the piping. The lower nut (not furnished) adjusts the pipe line to the proper elevation. The top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Material: Carbon Steel frame with a Cast Iron Roll.
PAGE 69
Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) CR-729A — Roller Chair RC-729 — Adjustable Roll Support Designed for longitudinal movement of pipe where vertical adjustment is not required. Although two bolts are supplied for installation, the chair can be alternatively welded in position. Material: Cast Iron Pipe Roll and Sockets, Carbon Steel Axle, Continuous Thread Rods and Hex Nuts. Do not exceed 450°F / 232°C at the contact point to the roll.
PAGE 70
Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) Metal Framing, Pipe Hangers and Accessories RC-729A — Adjustable Roll Support D-70 B Designed for longitudinal movement of pipe where vertical adjustment is required. Although primarily used for support of the pipe, this component may also be placed over the pipe to act as a guide. Material: A Cast Iron Pipe Roll and Sockets with a Carbon Steel Axle. Do not exceed 450°F / 232°C at the contact point to the roll.
PAGE 71
Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) S-730-C — Chair and Roll Designed for longitudinal movement of pipe where vertical adjustment is not required. Because the chair is made of steel, it can be either welded or bolted in position. Material: Carbon Steel Chair and Axle with Cast Iron Pipe Roll. Use a Figure 17 when a Cast Iron Chair is required. Do not exceed 450°F / 232°C at the contact point to the roll. BARE CHAIR PIPE NO. SIZE Finish: Black (add suffix “-B”).
PAGE 72
Pipe Straps, Conduit Clamps & Hangers Pipe Attachments Metal Framing, Pipe Hangers and Accessories CR-786 — Adjustable Pipe Support Used for support of piping from below without welding to the pipe, and consists of a steel saddle, nipple and pipe reducer. It connects to a threaded pipe standard and base. B Materials: Reducer is Cast Iron, Pipe saddle and nipple are carbon steel. Compliance: Federal Specification A-A-1192A Type 39, MSS-SP-69 Type 39.
PAGE 73
Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields C-789, C-789A, C789B, C-789C, C-789D, C-789E — Pipe Covering Protection Saddle The C-789 saddles are used to protect the insulation against damage and keep heat loss to a minimum. They are designed for 1" to 5" of covering. All Saddles are 12" long with three tabs on each side for welding to pipe. Sizes 12" and larger have a welded-in center rib.
PAGE 74
Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields Metal Framing, Pipe Hangers and Accessories C-789 (continued) D-74 CAT. NO.
PAGE 75
Pipe Straps, Conduit Clamps & Hangers Pipe Saddles & Pipe Shields Covering Thickness 12" Center Rib Sizes 12" & Larger B B A Figure 2 C-789 C-789 (continued) CAT. NO.
PAGE 76
Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields (continued) Metal Framing, Pipe Hangers and Accessories C-790 — Insulation Shield Designed to protect the insulation and distribute the load at the hanger point. This item is usually used with our C-710 Clevis Hanger. Approvals: Federal Specification A-A-1192A Type 40, MSS-SP-69 Type 40. Material: Carbon Steel. Finish: Standard Finish – GoldGalv®, Black (add suffix “-B”), Electro-Galvanized (add suffix “-EG”).
PAGE 77
Pipe Straps, Conduit Clamps & Hangers Rods and Rod Attachments How to Order Shield Size Selection Table CAT. NO.
PAGE 78
Pipe Straps, Conduit Clamps & Hangers Rods and Rod Attachments (continued) Metal Framing, Pipe Hangers and Accessories E-157 — Machine Thread Eye Rod D-78 B Welded Eyerods are designed to permit swing in the attachment component due to pipe movement. Material: A D Carbon Steel.
PAGE 79
Pipe Straps, Conduit Clamps & Hangers Rods and Rod Attachments (continued) F-111 — Forged Steel Clevis Tap Used to connect rod ends with structural steel welding lug plates or lugs welded to pipe. It provides a pivot point and adjustment. It can be supplied with a pin as F-111.
PAGE 80
Surface Raceway & Lighting Systems Metal Framing, Pipe Hangers and Accessories Series 800 Surface Raceway and Lighting Systems Electrical Raceway Superstrut® channel together with snap in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories listed by Underwriters Laboratories are identified on the drawings. Electrical Applications Column A Suitable for number of wires indicated when used as a raceway.
PAGE 81
Surface Raceway & Lighting Systems Electrical Applications (continued) Surface Raceway Systems AB-888 Page D-84 822 Page D-83 H104 Page D-13 Metal Framing, Pipe Hangers and Accessories 805 Page D-83 AB-844 Page D-84 A-854 Page D-83 A-853 Page D-83 AB-803 Page D-84 A-853 Page D-83 AB-885 Page D-84 811 Page D-83 804 Page D-83 Standard Finish – GoldGalv® brand AB-866 Page D-84 D-81
PAGE 82
Surface Raceway & Lighting Systems Electrical Applications (continued) Metal Framing, Pipe Hangers and Accessories A-891 Page D-83 AB-888 Page D-84 A-892 Page D-83 A-853 Page D-83 A-854 Page D-83 AB-844 Page D-84 Standard Finish – GoldGalv brand ® A-854 Page D-83 AB-288 Page D-17 E-145 Page D-11 802 Page D-83 ES-145 Page D-11 A-1200-P Page D-7 Order nuts separately 452TB Concrete Spot Insert Page D-23 D-82 540 Side Beam Hanger Clip Page D-26 S-541 Swing Connector Page D-27 500 Beam Clamp Pag
PAGE 83
Surface Raceway & Lighting Systems 1 3⁄8" ⁄32" 3 Fixture Fittings * Listed ⁄4"–16 UNF Thread 3 1 ⁄32" 21 A-243-1 End Cap for A-1200 Channel 4 1⁄2" 7 A-213 ⁄8" 21⁄16" CAT. NO. A802 B-802 E-802 H-802 FOR CHANNEL STD. CTN. A Series B Series E Series H Series 25 25 10 10 809 Tapped End Cap 12 ga for 3⁄ 4" or 1" Conduit. Furnished complete with 1⁄ 4" x 5⁄ 8" Flat Head Machine Screw and AB-100-1⁄4" nut. CAT. NO. FOR CHANNEL STD. CTN. A Series H Series 25 25 A-809 H-809 804 End Cap CAT.
PAGE 84
Surface Raceway & Lighting Systems Metal Framing, Pipe Hangers and Accessories Fixture Fittings (continued) * Listed 15⁄8" 4 3⁄4" 4" AB803* Cast Conduit Connector To connect 1⁄2" or 3⁄4" conduit to raceway channel — Furnished complete with stud nuts & hex nuts. Part has removable bushing to increase size from 1⁄2" to 3⁄4". AB815 Swing Connector Nuts & bolts to clamp to channel included. For 1⁄2" or 3⁄4" conduit.
PAGE 85
Special Metals Properties for Design Stainless Steel (Suffix SS/Type 304 and 6SS/Type 316) Superstrut® stainless steel products are made from high-quality austenitic Type 304 and Type 316 material. Stainless steel contains large amounts of chromium and nickel, is non magnetic and offers superior corrosion resistance. Tolerant to hightemperature environments, Superstrut’s stainless steel framing provides dependable support, resulting in reduced maintenance cost.
PAGE 86
Special Metals Metal Framing, Pipe Hangers and Accessories Aluminum Products (AL Suffix) 1 5⁄8" 1 ⁄8" 5 ⁄8" 7 3 ⁄4" 1 5⁄8" ⁄8" 7 A Series A-1200 1 5⁄8" deep channel and combination A-1202 A-1200-HS Slots 2" on center. Slot size 9⁄16" x 1 1⁄8" 1 5⁄8" 1 5⁄8" ⁄8" 7 ⁄16" 13 1 5⁄8" 12 ga. B Series B-1200 A-100 Regular Spring Nut D-86 12 ga.
PAGE 87
Special Metals Type #304 Stainless Steel Products (SS Suffix) 1 5⁄8" 7 ⁄8" 1 5⁄8" ⁄8" 7 A Series A-1202 A-1200-HS 1 5⁄8" 7 ⁄8" ⁄16" 13 B Series A-1202-HS B-1400 ⁄8" 7 B-1400-HS A-100 Regular Spring Nut B-100 Short Spring Nut AB-100 Springless Nut E-142 Hex Head Cap Screw E-145 Standard Hex Nut EF-147 Fender Washer Metal Framing, Pipe Hangers and Accessories A-1200 D-87
PAGE 88
Special Metals Type #304 Stainless Steel Products (SS Suffix) (continued) Metal Framing, Pipe Hangers and Accessories AB-241 CAT. NO. AB-241-1/4 AB-241-3/8 AB-241-1/2 E-147 Flat Steel Washer ROD SIZE (IN.) STD. CTN. ⁄4 ⁄8 1 ⁄2 100 100 100 1 3 U501, U502 H-119 Rod Coupling CAT. NO. FOR CHANNEL U501 A-1200 A-1400 B-1200 B-1400 C-1200 B-1402 A-1202 A-1402 C-1202 H-1200 A U502 A (IN.) STD. CTN. 33⁄ 16 20 413⁄ 16 20 Furnished complete Design Load U501 — 2150 lbs. U502 — 3000 lbs.
PAGE 89
Special Metals Type #304 Stainless Steel Products (SS Suffix) (continued) 47⁄8" 1 5⁄8" 2 1⁄2" 2" 17⁄8" X201 AB202 3 5⁄8" 3 5⁄8" 2 1⁄4" 41⁄8" AB203 AB206 AB204 5 3⁄8" 7 1⁄4" 41⁄8" 31⁄2" AB207 X207 Metal Framing, Pipe Hangers and Accessories 6H Series 6H-B Series Conduit and Pipe Hanger AB213 31⁄2" 9 5⁄32" 3 3⁄4" 41⁄8" 31⁄2" 3 7⁄8" 31⁄2" 1 5⁄8" AB214 AB219 1 21⁄32" AW219 D-89
PAGE 90
Special Metals Type #304 Stainless Steel Products (SS Suffix) (continued) Metal Framing, Pipe Hangers and Accessories 5 5⁄8" 3" 45˚ 3 1⁄2" 45˚ 31⁄2" 1 1⁄16" 2 5⁄16" 2 1⁄2" AB220 SPAB-227 AB225 3 1⁄4" 4 Holes 3 ⁄4" Dia. ⁄4" Dia. 3 111⁄16" 1 ⁄8" 5 3 1⁄2" 1 ⁄16" 11 31⁄2" 3 1⁄2" ⁄4" Dia. 3 6" 6" 6" 4 1⁄4" 4 1⁄4" 6" AP-235 AP-232SQ AP-232 4 3⁄4" 4 Holes 3 ⁄4" Dia.
PAGE 91
Special Metals Type #316 Stainless Steel Products (T316SS Suffix) 1 5⁄8" 7 ⁄8" 1 5⁄8" 7 ⁄8" ⁄16" 13 1 ⁄8" 5 B Series A Series ⁄8" 7 A-1200-HS-T316SS B-1400-T316SS Metal Framing, Pipe Hangers and Accessories A-1200-T316SS 5 3⁄8" 3 1⁄2" ⁄8" 7 B-1400-HS-T316SS 45˚ 702 Pipe and Rigid or IMC Conduit Clamp AB220 3 1⁄2" 21⁄4" 2 1⁄2" H-104 • Hanger rod AB225 • Continuous threaded AB201 41⁄8" 31⁄2" 41⁄8" CAT. NO. NATIONAL COARSE THREAD SIZE THREADS DESIGN (IN.) PER INCH LOAD (LBS.) STD.
PAGE 92
Special Metals White Painted Products for the Computer Industry (WH Suffix) Metal Framing, Pipe Hangers and Accessories 1 5⁄8" 7 1 5⁄8" 7 ⁄8" ⁄8" 1 5⁄8" ⁄16" 13 B Series ⁄8" 7 A Series B-1400 A-1200-HS A-1200 ⁄8" 7 B-1400-HS A-1202-HS A-1202 4 7⁄8" 15⁄8" 2 1⁄2" 1 7⁄8" 2 ⁄2" 1 2 ⁄4" 1 2" 1 7⁄8" AB201 X201 AB219 41⁄8" 41⁄8" AB203 D-92 31⁄2" 1 7⁄8" 2" AW204 AB205
PAGE 93
Special Metals White Painted Products for the Computer Industry (WH Suffix) (continued) 3 7⁄8" 1" 1 7⁄8" 1 3⁄4" 1 7⁄8" 11⁄16" 13⁄4" 3 3⁄4" Metal Framing, Pipe Hangers and Accessories AW-205-R AW205 L N-205 5 3⁄8" 3 1⁄2" 7 1⁄4" AB-207 AB-206 X-207 5 7⁄16" 5 ⁄8" 5c" 3 3 1⁄2" 3 1⁄2" 3 7⁄8" 1e" 1 5⁄8" 1 21⁄32" 1 5⁄8" A210 For attaching A Series channel A218 5 3⁄8" AB-219 45˚ 3" 2 5⁄16" 3 1⁄2" 3 1⁄2" 1 1⁄16" 5 3⁄8" N-219 AB-220 AB-227-WH D-93
PAGE 94
Special Metals Metal Framing, Pipe Hangers and Accessories White Painted Products for the Computer Industry/Clean Room Applications (WH Suffix) 5 3⁄8" AB-241 CAT. NO. ROD SIZE (IN.) STD. CTN. ⁄4 ⁄8 1 ⁄2 100 100 100 AB-241-1/4 AB-241-3/8 AB-241-1/2 1 3 5 3⁄8" AB253 4 Holes 3 ⁄4" Dia. 111⁄16" 15⁄8" 31⁄2" 3 1⁄2" 1 11⁄16" 4 Holes 3 ⁄4" Dia. 3 1⁄2" 6" 6" 6" 4 1⁄4" 4 1⁄4" AP-232SQ AP-232 4 Holes 3 ⁄4" Dia.
PAGE 95
Slotted Angle Metal Framing With Superangle, You Get Flexibility — Simplicity — Economy! Superangle Slotted Angle Metal Framing Create the support framing you need. Superangle is manufactured from structural-quality steel in three different sizes. The small sizes are 14 ga. steel, the larger size is 12 ga. steel. With this offering, an endless variety of metal framing requirements can be met, from light-weight supporting needs to larger shelving for inventory storage.
PAGE 96
Slotted Angle Metal Framing Metal Framing, Pipe Hangers and Accessories Superangle Slotted Angle Metal Framing (continued) CAT. NO. RA-160-10 RA-160-12 RA-225-10 RA-225-12 RA 300 10 RA-300-12 LENGTH (FT.) FT. PER PKG. STD. CTN. 10 12 10 12 10 12 50 60 50 60 50 60 1,000 1,200 1,000 1,200 1,000 1,200 5 Lengths, 36 Nuts and Bolts RA-300 12 Gauge 31⁄8" X 15⁄8" RA-225 14 Gauge 2 3⁄8" X 15⁄8" RA-160 14 Gauge 15⁄8" X 15⁄8" Superangle Accessories Casters STD. PKG. STD. CTN. 2 2 2 2 STD. PKG.
PAGE 97
Metal Framing Engineering Data Design Data — Metal Framing Channel Elements of Sections Nominal Thickness (IN.) W Y W Y X X Z X H X 12 ga. = .105 I — Moment of Inertia 14 ga. = .075 S — Section of Modulas 16 ga. = .060 r — Radius of Gyration Z H Z — Nominal Axis A — Area Single Channels Double Channels Table 1 — Properties for Design: Single Channel CAT. NO. H IN. W IN. A IN.2 I IN.4 S IN.3 R IN. X-X AXIS Z IN. I IN.4 S IN.3 Y-Y AXIS R IN.
PAGE 98
Metal Framing Engineering Data Design Loads for Channel Used as Beam or Column. Metal Framing, Pipe Hangers and Accessories Design Data — Metal Framing Channel (continued) Table 3 Beam Loads Table 3 contains simple beam, uniformly-distributed loads calculated at 25,000 psi fiber stress. Beam loads are based on channel being loaded across the x-x axis. Loads are also listed at reduced deflections for long spans.
PAGE 99
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 3 — Single Channel CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/180 SPAN 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 3,534 1,050 2,584 6,650 10,583 2,434 850 .014 .026 .016 .010 .008 .015 .028 — — — — — — — .067 .067 .067 .067 .067 .067 .067 — — — — — — — .033 .033 .033 .033 .033 .033 .
PAGE 100
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Metal Framing, Pipe Hangers and Accessories Table 3 — Double Channel (Single Channels Welded Back-to-Back) CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 — 3,016 — — — — 2,300 .008 .016 .010 .005 .004 .008 .016 — — — — — — — .067 .067 .067 .067 .067 .067 .067 — — — — — — — .033 .033 .033 .033 .033 .033 .
PAGE 101
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 3 — Single Channel CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/180 SPAN 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 1,178 350 861 2,216 3,528 811 284 .129 .236 .149 .088 .068 .126 .248 — — — — — — — .200 .200 .200 .200 .200 .200 .200 917 148 578 — — 640 115 .100 .100 .100 .100 .100 .100 .
PAGE 102
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Metal Framing, Pipe Hangers and Accessories Table 3 — Double Channel (Single Channels Welded Back-to-Back) CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 3,239 1,005 2,400 6,505 2,284 766 .071 .144 .085 .048 .036 .071 .144 — — — — — — — .200 .200 .200 .200 .200 .200 .200 — 702 — — — — 535 .100 .100 .100 .100 .100 .100 .
PAGE 103
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 3 — Single Channel CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/180 SPAN 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 706 210 516 1,330 2,116 486 170 .358 .658 .414 .244 .186 .353 .687 — 107 — — — — 82 .333 .333 .333 .333 .333 .333 .333 330 53 208 909 — 231 41 .167 .167 .167 .167 .167 .167 .
PAGE 104
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Metal Framing, Pipe Hangers and Accessories Table 3 — Double Channel (Single Channels Welded Back-to-Back) CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 1,944 604 1,444 3,904 6,434 1,370 460 .199 .398 .235 .133 .100 .199 .399 — — — — — — — .333 .333 .333 .333 .333 .333 .333 — 253 1,023 — — — 193 .167 .167 .167 .167 .167 .167 .
PAGE 105
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 3 — Single Channel CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/180 SPAN 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 441 — 323 831 1,323 304 — .914 — 1.059 .730 .478 .903 — 258 42 163 — — 180 32 .533 .533 .533 .533 .533 .533 .533 129 21 81 355 739 90 16 .267 .267 .267 .267 .267 .267 .267 3,108 — 1,960 5,423 7,059 2,615 — 12 12 12 12 12 14 14 393 — 288 739 1,176 270 — 1.
PAGE 106
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Metal Framing, Pipe Hangers and Accessories Table 3 — Double Channel (Single Channels Welded Back-to-Back) CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 1,215 378 903 2,440 4,021 856 288 .509 1.019 .603 .340 .255 .509 1.020 — 197 — — — — 150 .533 .533 .533 .533 .533 .533 .533 637 99 400 1,917 — 449 75 .267 .267 .267 .267 .267 .267 .
PAGE 107
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 3 — Single Channel MAXIMUM UNIFORM 1/180 SPAN 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 14 — — 475 756 — — — 1.912 1.463 — 84 53 233 482 60 .933 .933 .933 .933 .933 42 27 116 241 30 .467 .467 .467 .467 .467 — — — — — 12 12 — 661 — 1.910 178 369 1.07 1.07 89 185 .533 .533 — — 27⁄ 16 31⁄ 4 12 12 — — — — 140 292 1.20 1.20 70 146 .600 .
PAGE 108
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Metal Framing, Pipe Hangers and Accessories Table 3 — Double Channel (Single Channels Welded Back-to-Back) CAT. NO. DEPTH (IN.) MAXIMUM UNIFORM 1/360 SPAN GA. LOAD DEFL. LOAD DEFL. LOAD DEFL. COL. LOAD 12 12 12 12 12 14 14 694 — 515 1,394 2,298 489 — 1.563 — 1.850 1.040 .780 1.563 — 916 64 261 1,255 — 293 49 .933 .933 .933 .933 .933 .933 .933 208 32 130 626 1,326 147 25 .467 .467 .467 .467 .467 .467 .
PAGE 109
Metal Framing Engineering Data Design Data — Metal Framing Channel (continued) Table 4 — Safe Bearing Loads for 15⁄ 8" Channel and Combinations RECOMMENDED LOAD IN LBS. SECTION RECOMMENDED LOAD IN LBS. SECTION RECOMMENDED LOAD IN LBS.
PAGE 110
Metal Framing Engineering Data Design Applications Metal Framing, Pipe Hangers and Accessories Cantilever Beams Simple Beams Beams Fixed on One End, Supported at Other Beams Fixed at Both Ends D-110
PAGE 111
Metal Framing Engineering Data Design Applications (continued) Load tables on page D-50–D-56 for A, B, C, E and H series channel are for single span beams supported at the ends. These can be used in the majority of cases. There are times when it is necessary to know what happens with other loading and support conditions. Some common arrangements are shown in Table 6. Simply multiply the loads from the Design Load Tables times the factors given in Table 6. Examples shown on page D-112.
PAGE 112
Metal Framing Engineering Data Design Applications (continued) EXAMPLE I Metal Framing, Pipe Hangers and Accessories PROBLEM: Determine the load and deflection of an A-1200 beam continuous 5"–0" 5"–0" over one support and loaded uniformly on one span. SOLUTION: A. From load table 3 for A-1200 the load for a 5'0" span is 706 lbs. and deflection is .358". B. Multiply by factors from Table 6. Load = 706 lbs. x 1.30 = 917.8 lbs. Deflection = .358 x .92 = .
PAGE 113
Metal Framing Engineering Data Design Applications (continued) Table 7 — Load Carrying Capacities of Hot-Rolled Steel Rod NOMINAL ROD DIA. Table 8 — Rod Size Determined by Pipe Size for Fire Protection DIMENSIONS (IN.) — LOADS ROOT AREA THREAD .068 .126 .202 .302 .419 1 1 3 ⁄ 4 to 2 21⁄ 2 to 31⁄ 2 4 to 5 6 8 to 12 Safety factor of 5. ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 1 Safety factor of 5. Table 9 — Maximum Spacing between Pipe Supports Steel Pipe Nom. Pipe Size (IN.) Max. Spacing (FT.
PAGE 114
Metal Framing Engineering Data Metal Framing, Pipe Hangers and Accessories Design Applications (continued) Table 11 — Standard Dimensions and Weights of Piping Materials and Conduit MECHANICAL (SCHEDULE 40) NOMINAL STD. PIPE SIZE (IN.) PIPE O.D. (IN.) COUPLING O.D. (IN.) ⁄2 ⁄4 1 11⁄ 4 11⁄ 2 2 21⁄ 2 3 31⁄ 2 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 .84 1.05 1.32 1.66 1.90 2.38 2.88 3.50 4.00 4.50 5.56 6.63 8.63 10.75 12.75 14.00 16.00 18.00 20.00 22.00 24.00 26.00 28.00 30.00 1.06 1.31 1.58 1.90 2.
PAGE 115
Metal Framing Engineering Data Design Applications (continued) Table 12 — Extra Strong Pipe (Schedule 80) A.S.A. B36.10 SCHEDULE NOS. AND NOMINAL WALL THICKNESS DESIGNATIONS OUTSIDE DIAMETER (IN.) WALL THICKNESS (IN.) INSIDE DIAMETER (IN.) ⁄8 ⁄2 3 ⁄4 1 11⁄ 4 11 ⁄ 2 2 2 1⁄ 2 3 3 1⁄ 2 4 5 6 8 10 12 14 OD 16 OD 18 OD 20 OD 24 OD 10 12 14 OD 16 OD 18 OD 20 OD 24 OD .675 .840 1.050 1.315 1.660 1.900 2.375 2.875 3.500 4.000 4.500 5.563 6.625 8.625 10.750 12.750 14.000 16.000 18.000 20.000 24.000 10.750 12.
PAGE 116
Metal Framing Engineering Data Metal Framing, Pipe Hangers and Accessories Design Applications (continued) • General Storage Racks • Pallet Racks • Barrel Racks Column height, equal shelf spacing • Cable Racks • Bar Stock Racks • Display Racks • Special Purpose Racks • For Uniform Loads on Horizontal Members, See Table 3 Typical general storage rack for use with plywood or other decking Table 14 — Column Loading for Rack Construction COLUMN HEIGHT 6' 7' 8' 9' 10' D-116 • Bulk Furniture Racks CA
PAGE 117
Metal Framing Engineering Data Federal Specifications (WW-H-171)/ Manufacturers Society Specifications (MSS SP69) C-727 / CT-727 Adj. Swivel Ring Hanger Sizes 1⁄ 2" through 8" IPS 1 ⁄ 2" through 4" tube Federal Type 10 SP69 Type 10 A C-726 Steel Double Bolt Pipe Clamp Sizes 11⁄ 2" through 24" IPS Federal Type 3 SP69 Type 3 M-718 / MT-718 MI Split Pipe Ring w/wo turnbuckle adj.
PAGE 118
Metal Framing Engineering Data Metal Framing, Pipe Hangers and Accessories Federal Specifications (WW-H-171)/ Manufacturers Society Specifications (MSS SP69) C-704-A Offset J-Hook 1 Sizes ⁄ 2" through 3" IPS Federal Type 27 C-739-H Heavy Welded Steel Bracket Max. Load 3,000 lbs.