Instruction Manual

ManualsBrandsSure Heat ManualsHardwareSGR30M Natural Gas Conversion Kit

30" Natural Gas Conversion Manual

FOR OUTDOOR USE ONLY

Part No. Qty Description

1 RCOZZ00115A 1 Main Burner Valve & Manifold Assembly with Valves (NG)

2 RCOZZ00117A 1 Hose 27" - 3/8" Flare Both Ends for Side Burner (NG)

3 RCOZZ00008A 1 Sealant Pipe (4ml)

4 RCOZZ00116A 1 Side Burner Valve Assembly - 12K BTU (NG)

5 RCOZZ00117A 1 NG Regulator 3/8” NPT x 3/8” UNF

6 RCODZ00026A 2 Orifice Back IR NG"

7 RCOZA00021A 1 Tee Fitting - Galvanized 3/8" UNF

8 RCODZ00024A 1 Connector 3/8” NPT x 3/8” UNF

9 SBNAA00025A 1 IR Side Burner Orifice Holder

10 RHWAZ00027A 1 Phillips Panhead Screw M4 x 6

11 RCOZZ00118A 1 Wrench

NOTE: Images in this manual may differ slightly from your grill.

Summary of content (8 pages)

PAGE 1
30" Natural Gas Conversion Manual FOR OUTDOOR USE ONLY 1 2 10 9 3 7 4 8 11 6 5 1 2 Part No.
PAGE 2
SGR30M Natural Gas Conversion Instructions Tools Needed: Phillips head screwdriver 3/4” wrench 1/4” wrench or socket Adjustable wrench Fig 2 * 1/4” socket set with extension can also be used. Be sure gas supply is off, the knobs are in the off position and the grill is cool. 1. Use a 3/4” wrench disconnect the hose from the side burner valve and pull the hose back into the cart. (See Fig. 1) 2. Use a 3/4” wrench disconnect the other hose from the manifold.(See Fig. 2) 3.
PAGE 3
SGR30M Natural Gas Conversion Instructions 7. Pull the searing burner out a little and use an adjustable wrench to disconnect the flex line from the burner, then disconnect the igniter wire. (See Fig. 7) NOTE: Make sure the wire does not fall into the access hole. Fig 9 8. Remove the searing burner. 9. Remove the (6) screws holding the front heat shield in place.(See Fig. 8) 10. Lift the front heat shield out of the grill. (See Fig. 9) 11. Disconnect the wires from the main burner igniter.(See Fig.
PAGE 4
SGR30M Natural Gas Conversion Instructions 15. Remove all the knobs, set the knobs aside. (See Fig. 14) 16. Remove the screws holding the main burner knob bezels to the front face and remove the bezels. (See Fig. 15) Fig 14 17. Hold the manifold, slightly move it to the right and lift the left end out. (See Fig. 16) 18. Lift the left end of the manifold up, carefully remove the manifold out of the grill. (See Fig. 17) You are now ready to install the new NG manifold. Fig 15 19.
PAGE 5
SGR30M Natural Gas Conversion Instructions 27. Place the searing burner in to the firebox, connect the flex line and then connect the igniter wire. (See Fig. 7 on page 3) Fig 19 28. Push the searing burner in position, connect the, secure the burner with the screws removed in step 5-6. (See Fig. 5-6 on page 2) 29.Reinstall burners into the grill body. Line up the burners with the valves on the manifold, making sure they are level. (See Fig. 20) 30. Connect the igniter wires to the igniter. (See Fig.
PAGE 6
SGR30M Natural Gas Conversion Instructions Installing the NG regulator NOTE: Make sure to use supplied pipe sealant on all non-flared fittings. Fig 21 1. Attach the tee fitting to the manifold as shown. Tighten with wrench. (See Fig. 21) 2. .Attach the Connector 3/8” NPT x 3/8” UNF to the tee fitting as shown. Tighten with wrench. (See Fig. 22) 3. Attach the NG regulator to the tee fitting. (See Fig. 23) Fig 22 4.
PAGE 7
SGR30M Natural Gas Conversion Instructions holding the side burner orifice holder. (See Fig.25) 2. Remove the side burner orifice. (See Fig. 26) Fig 25 3. Remove the side burner knob. (See Fig. 27) 4. Remove the (2) screws holding the side burner bezel and valve. (See Fig. 28) 5. Remove the side burner valve assembly and replace it with NG valve assembly. Bracket 6. Slide the valve assembly through the center hole in the front of the shelf. (See Fig. 29) Orifice holder 7.
PAGE 8
SGR30M Natural Gas Conversion Instructions 1. Remove the six (6) screws on the inside of the grill that hold the rear infrared cover in place. (See Fig. 30) Fig 30 2. Close the grill hood slowly. 3. Grasp rear infrared cover and remove it from the grill. (See Fig. 31) 4. Use the wrench supplied with this kit to remove the LP orifice. (See Fig. 32) 5. NG orifice. (See Fig 19 on page 5) Fig 31 6. Install the NG orifice. (See Fig 33) 7. Use the screws removed in step 1 to secure the rear infrared cover.