Manual

LIGHTING INSTRUCTIONS
1. STOP!Readthesafetyinformationlabelfoundontheunit.
2. Makesuretheswitch(NotthePilot Control Knob)isturnedto“OFF”(See Figure 4)
3. Turnoffallelectricalpowertotheunit.
4. Push in Pilot Control Knobslightlyandturnclockwiseto“OFF”.
5. Waitve(5)minutestoclearoutanygas.Thensmellforgas,includingneartheoor.
 • Ifyousmellgas,STOP!Follow“B”ontheSafetyInformationlabel.
 • Ifyoudon’tsmellgascontinueontothenextstep.
6. Thepilotislocatedbythemainburner.
7. Push in the Pilot Control Knobslightlyandturncounter-clockwiseto“Pilot”.
8. Hold the Pilot Control Knobslightlyandturncounter-clockwiseto“Pilot”.
9. ContinueholdingthePilot Control Knobforuptoone(1)minutebeforereleasing.Theknobwillpopbackoutupon
release. Pilot should remain lit. If it goes out repeat steps 5 through 8.
 • Ifknobdoesnotpopoutwhenreleased,stopandimmediatelycallyourservicetechnician.
 • Ifthepilotwillnotstaylitafterseveraltries,turnthegascontrolknobto“OFF”andcallyourservicetechnician.
10. Push in the Pilot Control Knobandturncounter-clockwiseto“ON”.
11. It will take 2-3 minutes for thermocouple to heat up and ame to appear.
12. ThisvalveisequippedwithaHI/LOfeature.Setunittodesiredameheight.Thevalveisalsoequippedwitha
 safetylockoutfeaturethatwillpreventtherelightingofthepilotafteritisextinguished.Youmustwaitone(1)minute
for valve to reset itself before relighting the pilot.
13. Thenmoveswitchtoremote.Youwillthenbeabletoswitchtheunit“ON”or“OFF”usingtheremote.
14. Tooperateunitwithremote:
 a. Makesureswitchisturnedto“REMOTE”
 b. MakesurePilot Control Knobisswitchedto“ON”
c. Press button oncetoturnunit“ON”.Youwillhearasoftbeepthantheamewillappear.
 d. Toturntheunit“OFF”.Pressthebuttonontheremoteonceafterve(5)secondstheamewilldisappearand
  theunitwillturnoff(NOTE:thepilotlightwillremainon).
Makesureswitch
is turned to “OFF”
whenlighting;and
“REMOTE” to use
the remote.
HI/LO
Setting
Pilot Control
Knob
Figure 4
MATCH LIGHTING INSTRUCTIONS
Ifthepilotcannotbeignitedwiththepiezo,itcanbemanuallylitwithamatch.Followsteps2through8intheabove
LightingInstructionsthen:
 • PushthePilot Control Knob in fully and hold it in.
 • Immediatelylightthepilotwithamatch.ContinuetoholdthePilot Control Knobinforaboutone(1)minute.
 • Afterone(1)minute,releasetheknobanditwillpopbackout.Thepilotshouldremainlit.Ifitgoesout,repeat
steps 2 through 8.
 • Ifthecontrolknobdoesnotpopoutwhenrelease,STOP and immediately call your service technician
or gas supplier.
 • Ifthepilotwillnotstaylitafterseveraltries,turnthePilot Control Knobclockwiseto“OFF”andcallyourservice
technician or gas supplier.
TO TURN GAS OFF TO APPLIANCE
1. Turntheswitchto“OFF”
2. Push in the Pilot Control Knobslightlyandturnclockwiseto“OFF”.DO NOT FORCE.
Page 9