Instructions / Assembly

ManualsBrandsSwing-N-Slide Playsets ManualsPlayground SetsGreen Olympus Wave Slide

Speciﬁ cations subject to change without notice.

Manufactured for: Swing-N-Slide® • 1212 Barberry Drive • Janesville, Wisconsin 53545 • USA • 1-800-888-1232 • www.swing-n-slide.com

Made in USA • Printed in USA

LDR 02-15-2019 LA 5940

Olympus Wave Slide Instructions

WS 5030

WS 5031 WS 5032

x22

x11

ASSEMBLY STEPS

1. Align slide sections and the backing plates together on

the ground (Fig. 1). Begin attaching two slide sections

together by securing the bolts in place ﬁ nger tight (see

Fig. 2 for proper Bolt Sequence). Following this pattern

install (1) bolt, (2) washers and (1) lock-nut per hole

(see Fig. 1).

Once all (11) bolts, (22) ﬂ at washers and (11) lock-nuts

are in place go back and tighten all hardware with

appropriate tools.

IMPORTANT: Tighten securely so backing plates

and slide sections are tight against each other AND

there are a minimum of one to two threads extending

beyond each lock-nut.

Fig. 1

Fig. 2

Not Included In Kit:

Fits 60” (152,4 cm) Deck Height

FOR PRIVATE USE ONLY

DO NOT USE IN PUBLIC SETTNGS!

Weight Limit: 250 lbs

For children 2-10 years of age

Tighten nut until washers are tight against backing plates.

(11) 5/16” (7,8 mm) Lock-nut

(11) 5/16” x 1”

(7,8 mm x 19 mm)

Hex Head Bolt

(22) 5/16” (7,8 mm)

Flat Washers

Backing Plates

Stake

2” x 4” x 17” (5,1 x 10,2 x 43,1 cm)

Use Pressure-Treated Wood

1-3/4”

(4,4 cm)

17” (43,1 cm)

Cut

1-3/4” (4,4 cm)

Tape Measure

Hammer

1/8” & 1/4” Drill Bits

Phillips Bit

WARNING: Assembly by adult.

AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.

ADVERTENCIA: El ensamblaje lo debe hacer un adulto.

WARNING: ASSEMBLY BY ADULT.

WARNING: ASSEMBLY BY ADULT

Circular Saw

Electric Drill

Socket Wrench set /

Wrenches

KIT INCLUDES:

x11

Hex Bolt

1-1/4”

(3,2 cm)

Deck Screw

1-1/4”

(3,2 cm)

1/4”

(6 mm)

1/2”

(12,7 mm)

Truss Screw

Tools Required:

Screw size should be a #8 thread size

minimum and coated for use

with treated wood.

Screw must be to sizes shown at a

minimum. Do not use a screw size

shorter than 1-1/4” (3,2 cm) long.

Summary of content (4 pages)

PAGE 1
Olympus Wave Slide Instructions WS 5030 WS 5031 WS 5032 WARNING: Assembly by adult. AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte. ADVERTENCIA: El ensamblaje lo debe hacer un adulto. FOR PRIVATE USE ONLY DO NOT USE IN PUBLIC SETTNGS! WARNING: ASSEMBLY BY ADULT.
PAGE 2
. Assembly: Pre-drill dimple holes through slide with 1/4” drill bit ﬁrst Fig. 3 (Fig. 44a) . Fig. 44b x4 . 1-1/4” Truss Screws (not included) 21” USE ZONE 72” 21” Fig. 5 1-3/4” Minimum Fig. 4 Pre-drill holes in slide with 1/8” drill bit ﬁrst (2) 1-1/4” screws (not included) 1-3/4” Minimum 2” above ground Stake 2” x 4” x 17” Use Pressure-Treated Wood ASSEMBLY STEPS 1. Consult (Fig. 3) for proper placement of slide on your unit.
PAGE 3
Safety Checklist for Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety – Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on approved designs? (Do not alter its design or add/remove components.) Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.
PAGE 4
Warranty and Registration Register your product online at www.OnlineWarranty.net LA 5940 LDR 02-15-2019 Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides conﬁ dence and demonstrates our commitment to providing quality residential playground products.