Replacement Part List

11
- The above Spreader Chart settings are based off of a 10’ spread width. Always trial test the application rate.
- Depending on the material you are spreading, the spread width could be higher or lower than what is shown.
- All measurements are taken with the Motor Assembly at the furthest setting from the Deflector (see pg 5).
- Formula for calibration of other products not listed above:
Flow Rate (lbs/min): Material (lbs/min) that flows through selected hopper gate setting per minute
(Motor Assembly removed, see pg 5).
Coverage (sq-ft/min): Material spread width (trial test required) multiplied by the distance traveled per minute
(4 mph = 352 ft/min; 3 mph = 264 ft/min; 2 mph = 176 ft/min; 1 mph = 88 ft/min).
Flow Rate (lbs/min) lbs/Acre
Coverage (sq-ft/min) 43,560 (sq-ft in 1 Acre)
X
Helpful Tips
• Read Owner’s Manual before use and be sure to follow all safety label precautions provided on the
Spreader Hopper.
• Always use ONLY CLEAN DRY MATERIAL and be sure the remove all unused material from
the Hopper after each use. Damp materials will cause material flow problems and material
freezing problems in cold temperatures.
• Be sure material is free of foreign matter such as packaging etc.
• Some materials may jam the Hopper Gate at lower settings so it may be necessary to use a larger
setting and increase your mph to compensate for the increased material flow rate. Increasing your
ground speed from 4 mph to 8 mph will decrease your application rate per acre by half if the same
setting is used at both speeds.
• Light seed such as Kentucky Blue Grass can be mixed with a seed such as clover to aid in material
flow at a 50/50 mix.
• Increased material density per acre can be achieved by adjusting the Motor Assembly closer to the
Deflector and Hopper Gate. This accomplishes a narrower spread width, providing more lbs/sq-ft of
material.
• Do not spread light seed in windy conditions as poor coverage will result.
• Proper material coverage is achieved with the greatest satisfaction by covering the desired area
twice at half the recommended application rate indicated by the manufacturer of the material. Once
by traveling length ways then by traveling cross ways to account for any underlap issues. The
adjustment of the application rate can be made either by adjusting the Hopper Gate to a lesser
setting or by increasing the ground speed of the application vehicle.
• When using the Spreader for salt/ice melts, fertilizer or other corrosive materials it is imperative that
the Spreader is thoroughly cleaned to prevent corrosion causing premature failure of the product.
Product Se tting 1 Se tting 2 Se tting 3 Se tting 4
lbs/Acre lbs/Acre lbs/Acre lbs/Acre
41 @ 4 mph 169 @ 4 mph N/A N/A
20 @ 4 mph 84 @ 4 mph N/A N/A
N/A N/A 226 @ 4 mph 352 @ 4 mph
N/A N/A 113 @ 8 mph 176 @ 8 mph
151 @ 4 mph 536 @ 4 mph N/A N/A
75 @ 8 mph 268 @ 8 mph N/A N/A
N/A 56 @ 4 mph 170 @ 4 mph N/A
N/A 28 @ 8 mph 85 @ 8 mph N/A
N/A 82 @ 4 mph 288 @ 4 mph N/A
N/A 41 @ 8 mph 144 @ 8 mph N/A
N/A 53 @ 4 mph N/A N/A
N/A 26 @ 8 mph N/A N/A
Dry Sa nd
Red Fescue
Material Spreading Chart
(Calibrated at 4 mph Ground Speed)
Fertilizer
Rock S a lt
Barle y
Oats