Instructions
Intended use
This radio wall switch can be used for programming and controlling
a suitable radio receiver. With optimal ambient conditions the range
is up to 70 meters.
The radio wall switch is powered by a 12 V battery (type: 27A).
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify
this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European
requirements. All company names and product names are trademarks
of their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other
devices which are connected to the product.
• Check the product for damage before each use! If you notice any
damage, do not use the product any longer! There is a risk of a life-
threatening electric shock!
• Ensure that the insulation for the entire product is neither damaged
nor destroyed. Never disassemble the product! There are no ser-
viceable parts inside.
• Do not use this product in hospitals or medical institutions. Although
the product emits only relatively weak radio signals, these may lead
to the malfunction of life-support systems. The same may also be
the case in other areas.
• Keep the product away from strong magnetic elds occurring near
machines, electric motors or loudspeakers.
• Consult an expert when in doubt about operation, safety or
connection of the device.
• Maintenance, modications and repairs are to be performed
exclusively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for
a long period of time to avoid damage through leaking. Leaking or
damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batte-
ries lying around, as there is risk, that children or pets swallow them.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge non-rechargeable batteries. There is a risk of
explosion!
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RSL wireless wall switch
• Battery 12 V/27 A
• Operating instructions
Operating instructions
RSL wireless wall switch 1 channel
Item no. 1761735
Connection and installation
The wireless wall switch is only intended for use in
dry indoor locations.
Make sure that cables or wires are not damaged when
drilling or bolting in place.
• Lift the front plate of the radio wall
switch (e.g. using a screw driver)
carefully and remove it (see gure
to the right).
• Remove the mounting plate. The
mounting plate of the radio wall
switch is attached to the electronic
component of the radio wall switch
with 4 clips (see gure to the right).
• The mounting plate disposes of the
mounting holes (see gure to the
right). Use the mounting plate to
mark the mounting holes on the wall.
• Drill the mounting holes.
• Fix the mounting plate with suitable
installation material to the desired
mounting location.
• Fasten the electronic component of
the radio wall switch to the mounting
plate.
• Insert a 12V-battery (type: 27A) into
the battery compartment of the radio
wall switch with the correct polarity.
• Attach the front plate to the wireless wall switch.