Instructions

Intended use
This wireless motion detector serves to switch a corresponding
receiver (e.g. wireless power socket, wireless external power
socket switch, etc.) on or off. The mount dimmer has a horizontal
movement detection range of 90° (max. detection range up to 8
metres). The movement detection range can be limited with the
diffuser lens included in the delivery. Moreover, the activation du-
ration upon movement detection (6 s, 15 s, 1 min, 5 min) and the
brightness sensitivity can be adjusted.
The wireless motion detector is only intended for use in dry indoor
locations.
It is powered by 2 x 1.5 V batteries (type: AAA).
All the safety and operating instructions in this manual must be
followed carefully. These instructions not only protect the device
but, in particular, your health. Please read the entire operating
manual before using the product.
This product complies with the applicable National and Euro-
pean requirements. All names of companies and products are the
trademarks of the respective owner.
All rights reserved.
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/
downloads or scan the QR code shown. Follow the instructions
on the website.
Delivery Contents
• Motion detector
• 2 x 1.5 V type-A batteries
• Operating instructions
Safety instructions
The warranty will be void in the event of damage
caused by failure to observe these safety instruc-
tions. We do not assume any liability for any con-
sequential damage!
Nor do we assume liability for damage to property
or personal injury caused by improper use or fail-
ure to observe the safety instructions. The war-
ranty will be null and void in such cases.
a) General
• The unauthorised conversion and/or modication of the prod-
uct is inadmissible because of safety and approval reasons.
• Do not use this product in hospitals or medical institutions.
Although the product emits only relatively weak radio signals,
these may lead to the malfunction of life-support systems.
The same may possibly be the case in other areas.
• The wireless motion detector is powered by 2 x 1.5 V micro
batteries (type: AAA).
• The product is not a toy and must be kept out of the reach of
children. Therefore, be especially careful when children are
around.
• Never expose the motion detector to extremely high or ex-
tremely low temperatures, humidity or vibrations.
• Do not leave packing materials unattended. They may be-
come dangerous playthings for children.
• Handle the product with care, it can be damaged by impacts,
blows, or accidental drops, even from a low height.
b) Batteries
• Batteries should be kept out of the reach of children.
• Please pay attention to the correct polarity (plus/+ and mi-
nus/-) when inserting the battery.
• Do not leave batteries lying around in the open; there is a risk
of them being swallowed by children or domestic animals. If
swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of
the skin. Therefore, use suitable protective gloves.
• Make sure that batteries is neither short-circuited nor thrown
into a re. There is a risk of explosion!
• Do not recharge normal batteries. There is a risk of explosion!
Only charge rechargeable batteries that are intended for this
purpose; use a suitable battery charger.
• Remove the batteries when not in use over long periods (e.g.,
storage). Aging batteries may leak, which might cause dam-
age to the product and loss of guarantee/warranty!
• For environment friendly disposal of batteries and recharge-
able batteries, please read the chapter “Disposal“.
• Because rechargeable batteries have a lower voltage (re-
chargeable battery = 1.2 V battery = 1.5 V), we recommend
using high-quality alkaline batteries for the wireless motion
sensor to ensure long and safe operation.
c) Handling
• The wireless motion detector must not get damp or wet.
• Avoid the following unfavourable environmental conditions in
the during use and during transportation:
- Humidity and dampness may cause damage to the mo-
tion detector.
- Direct sunlight
- Extreme cold or heat
- Dust or ammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic elds such as those found in the vicinity
of machinery or loudspeakers
• Ensure that the enclosure of the entire product is neither dam-
aged nor destroyed. Never disassemble the product! Except
for changing the battery, there are no serviceable parts inside.
• Check the product for damage before use!
• If you notice any damage, do not use the product any longer!
• Safe operation must be presumed to be no longer possible:
- if the device is visibly damaged
- if the device no longer works
- if the device was stored under unfavourable conditions for
a long period of time
- the device was exposed to extraordinary stress caused by
transport.
Description of functions
This motion detector responds to heat radiation, which is emitted
by objects entering the detection area of the motion detector. The
motion detector must “see“ the area it is to keep under surveil-
lance. Heat radiation travels in straight lines but is obstructed,
for example, by glass or other xed objects. Before mounting,
therefore, pay attention to this, or other problem sources. If the
detection area of the motion detector is entered, the programmed
receiver (e.g. wireless power socket) is activated. The activation
duration can be adjusted at the motion detector. In addition, the
ambient brightness, at which the motion detector shall be acti-
vated, can be adjusted.
Installation
When selecting the position for installing the motion
detector, please note that it must not be subjected
to direct sunlight, humidity, vibrations, dust, heat or
cold. This can lead to faulty activation, defects or
functional impairment.
The motion detector is only suitable for use in dry,
closed indoor locations.
Do not place devices with strong magnetic or electric
elds, such as mobile phones, electric motors, etc. in
the immediate vicinity.
Recommended installation height: 1 to 1.5 metres
To ensure optimal motion detection, the motion de-
tector must be placed so that the object to be detec-
ted does not approach the motion detector directly
but passes from left to right or vice versa.
Proceed as follows, to ensure the correct installation:
• Use a at screw driver to remove the front plate with the dif-
fuser lens.
• The mounting plate at the back has two mounting holes. Take
the mounting plate and indicate the mounting holes at the in-
tended mounting position.
• Drill the holes.
• Fix the mounting plate with suitable installation material.
• Insert the electronic component into the mounting plate.
• Attach the front plate with the diffuser lens (so that it en-
gages).
Timer and brightness setup
The motion detector has two sliding switches for adjustment of
activation duration and brightness sensitivity.
Slide switch for activation duration: Slide switch: brightness
sensitivity:
Explanation:
6 s: Activation duration of 6 seconds
15 s: Activation duration of 15
seconds
1 m: Activation duration of 1 minute
5 m: Activation duration of 5 minutes
Explanation:
The closer the sliding switch
is positioned to the sun sym-
bol, the brighter the ambient
area upon activation due to
motion detection.
Operating Instructions
Wireless Motion Detector RSL
Item No. 1761752