Instructions

Intended use
The radio wall switch can wirelessly switch a suitable receiver of the
RS2W radio system (or a user connected to it) on or off. The radio wall
switch is operated via a type “CR2032” battery.
As a special feature the radio wall switch responds back per LED
whether the programmed radio receiver (max. 5 per channel) of the
RS2W radio system has received the key commands or not.
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or mo-
dify this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re etc. Read the
instructions carefully and keep them. Make this product available to
third parties only together with its operating instructions.
This product complies with the statutory national and European requi-
rements. All company names and product names are trademarks of
their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other de-
vices which are connected to the product.
• Do not use this product in hospitals or medical institutions. Although
transmitters of the RS2W system only emit relatively weak radio si-
gnals, these may lead to the malfunctioning of life-support systems.
The same may also apply to other areas.
• The product must not get damp or wet!
• Consult an expert when in doubt about operation, safety or connec-
tion of the device.
• Maintenance, modications and repairs are to be performed
exclusively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Batteries
• Correct polarity must be observed while inserting the batteries.
• Batteries should be removed from the device if it is not used for a
long period of time to avoid damage through leaking. Leaking or
damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batte-
ries lying around, as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and
new batteries in the device can lead to battery leakage and device
damage.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge non-rechargeable batteries. There is a risk of
explosion!
Inserting/replacing the battery
Delivery includes a “CR2032” type battery. This is pos-
sibly already inserted into the battery compartment. In
this case a protective synthetic strip between battery and
battery contacts prevents early recharge; remove it.
• Remove both rocker switches by inserting a athead screwdriver
between frame and rocker switch and subsequently levering out
both rocker switches carefully.
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RS2W wireless wall switch
• Battery CR2032
• Operating instructions
Operating instructions
RS2W wireless wall switch,
2 channels
Item no. 1761758 (white)
Item no. 1762777 (black)
• Place a battery of type “CR2032” with the correct polarity (or remo-
ve the protective synthetic strip). The plus pole of the button cells
points from you outward.
• Snap both rocker switches on again, pay attention to the correct
orientation (transparent opening in one of the two rocker switches
must be above the LED).
Pay attention to the next chapter “Assembly” in case the
wall-mounted switch must be screwed on, before you
snap on the rocker switches.
• The batteries need to be replaced if the range of the radio wall
switch is signicantly reduced or the LED no longer lights when the
button is pushed.
Assembly
Test the functioning of the radio wall switch and the regis-
tered radio receiver before you securely mount the radio
wall switch.
• Adhesive attachment
Use double-sided adhesive tape to attach the radio wall switch to an
appropriate surface. This must be smooth, clean and grease-free.
• Screw assembly
Remove both rocker switches by inserting a athead screwdriver
between frame and rocker switch and subsequently levering out
both rocker switches carefully.
Remove the central section (with the electronics) from the frame by
loosening the lateral clips.
The frame can now be attached with 2 - 4 suitable screws and, if
appropriate, plugs. Pay attention when drilling and tightening the
screws that no cable or pipes are damaged.
Reassemble the radio wall switch in a reversed order.
Operation
Keep a minimum distance of 20 - 30 cm between the ra-
dio wall switch and the radio receiver.
a) Resetting the radio wall switch
Perform a reset before the initial startup and tune in the radio
receiver(s) after that.
A reset also deletes all radio receivers tuned in/saved on the respec-
tive channel.
The reset only applies to the respective individual channel
- the second channel remains unaffected!
Proceed as follows to perform a reset:
• Press the “O” and “I” buttons at the same time one of the two rocker
switches (approx. 3 seconds) until the LED ashes red (then release
rocker switch for 1 - 2 seconds).
• Press the “O” and “I” buttons again for approx. 6 seconds, until the
LED ashes blue. Then, release the rocker switch again.
b) Programming a radio receiver to the radio wall switch
On every radio transmitter channel of the RS2W radio
system, up to 5 different radio receivers (e.g., radio
switchable socket) can be programmed. However, do not
mix radio switch and dimmer.