Installation Guide

ManualsBrandsSymmons ManualsBathDuro Single-Handle 1-Spray Tub and Shower Trim in Satin Nickel (Valve Not Included)

Model Numbers Speciﬁcation

Options/Modiﬁcations

Tub/shower trim with hand shower and lever handle

includes wall connection, 30” slide bar, in-line vacuum

breaker, exible metal hose, non-diverter tub spout,

1 mode hand shower and 1 mode showerhead with

standard 2.5 gpm (9.5 L/min) ow restrictor. Shower

trim with hand shower and lever handle includes all of

the above less non-diverter tub spout. Valve trim with

hand shower and lever handle includes all of the above

less non-diverter tub spout and 1 mode showerhead.

Components made from metal and nonmetallic

materials plated in standard polished chrome nish.

Duro™ Trim Series

Operation & Maintenance Manual

3603-H321-V-TRM, 3605-H321-V-TRM, 3606-H321-V-TRM

3603-H321-V-TRM

Valve Trim with Hand Shower

Compliance

-1.5

1.5 gpm (5.7 L/min) ﬂow restrictor

-2.0

2.0 gpm (7.6 L/min) ﬂow restrictor

-SS

Slip spout on any tub/shower unit

3605-H321-V-TRM

Shower Trim with Hand Shower

Note: Append appropriate -sufx to model number.

-ASME A112.18.1/CSA B125.1

3606-H321-V-TRM

Tub/Shower Trim with Hand Shower

-LW

Wide lever handle (chrome ﬁnish only)

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Summary of content (7 pages)

PAGE 1
3603-H321-V-TRM, 3605-H321-V-TRM, 3606-H321-V-TRM Duro™ Trim Series Operation & Maintenance Manual Model Numbers 3603-H321-V-TRM Valve Trim with Hand Shower 3605-H321-V-TRM Shower Trim with Hand Shower 3606-H321-V-TRM Tub/Shower Trim with Hand Shower Options/Modifications -1.5 1.5 gpm (5.
PAGE 2
Dimensions 3606-H321-V-TRM PICTURED A A B C B D D C E E F G H I J F K G L M N I O P Q R H M L K J Floor N P R Q Notes: 1) All dimensions measured from nominal rough-in (see O as reference). 2) Dimensions subject to change without notice. 2 O Measurements Ø 2 1/4”, 57 mm 5 7/8”, 149 mm 6”, 152 mm Male 1/2” NPT thread must be recessed 1/4” from finished wall Ref. 77”, 1956 mm 3 1/2”, 89 mm 5”, 127 mm 7 1/2”, 191 mm 10”, 254 mm Ø 2 1/2”, 64 mm (3606) Ref. 32”, 813 mm (3603, 3605) Ref.
PAGE 3
Parts Breakdown Replacement Parts C B A H F G N O M E G D P K I E Q J R J S HOT Water Supply D Item Description Part Number A Showerhead 362SH B C D E F G H I J K L M N O P Q R S Shower Arm Flange Handle Assembly Dome Cover Diverter Escutcheon Screws Mounting Plate Escutcheon Screws Mounting Plate Tub Spout Slide Bar Assembly Hand Shower Wall Elbow In-line Vacuum Breaker & 60” Hose 300S T-617 RTS-037 RTS-040 RTS-001 067 SC-115 EF-100 EF-105 EF-104 Notes: 1) Append -STN to part num
PAGE 4
Installation Note: For valve body installation, please see valve body installation guides. 3) Attach shower escutcheon (I) to large mounting plate (K). 1) Install small mounting plate (H) to diverter valve (2DIV-BODY or 3DIV-BODY) and large mounting plate (K) to shower valve (4000BODY). Secure each with two screws (G) and (J). 5) Install diverter handle (3605 and 3606 only) (D) and shower handle (D) to valves. Secure handles by tightening set screws. 1 K I D Note: Tabs should snap into place.
PAGE 5
Installation 7a) Dry Wall Option: Remove upper and lower caps (M) from slide bar brackets. Place slide bar (O) into desired position. Using brackets as a guide, carefully drill 3/16" holes into wall. Remove slide bar and install anchors. 7b) Stud Option: Remove upper and lower caps (M) from slide bar brackets. Place slide bar (O) into desired position. Using brackets as a guide, carefully drill 1/8" pilot holes into stud. 8) With slide bar (O) in position, secure to wall using screws (N).
PAGE 6
Installation 9) Install wall elbow (Q) to stub out pipe. Tighten set screw to secure. 11) Install showerhead (A) to shower arm (B). Turn clockwise to tighten. 1 Q 12) Attach large end of hand shower hose (S) to hand shower wand (P). Attach small end of hand shower hose (S) to in-line vacuum breaker (R). Connect inline vacuum breaker to wall elbow (Q). Turn clockwise to tighten. B 1 P A 2 2 1 2 S 10) Attach shower arm (B) and flange (C) to vertical shower pipe turning clockwise to tighten.
PAGE 7
Operation & Maintenance (Diverter Control: 2DIV-BODY) 1) Cartridge is factory set to divert to function 1. POSITION 1 2) Turn handle to position 2 to divert to function 2. POSITION 2 3) Turn handle to position 3 to share functions 1 and 2. POSITION 3 Note: In this position there is no detent. Operation & Maintenance (Diverter Control: 3DIV-BODY) 1) Cartridge is factory set to divert to function 1. POSITION 1 2) Turn handle to position 2 to share functions 1 and 3.