Owner manual

ManualsBrandsTalkaphone ManualsAccessories communicationEB-200 Base Station

Talk-A-Phone Co. Rev. 7-27-09

7530 North Natchez Avenue Niles, Illinois 60714-3804

Phone: (773) 539-1100 Fax: (773) 539-1241

e-mail: info@talkaphone.com http://www.talkaphone.com

Talk-A-Phone Co.

Creating Communication Solutions

Installation & Operation Manual

For EB-200 Base Station

Section

Page

Getting Started 2

Hardware Installation 3

Programming the Base Station 4

Operation 5

FCC Information 6

Phone Line Specifications 7

Information to the User 8

Talk-A-Phone Co. Limited Warranty 9

Summary of content (9 pages)

PAGE 1
Talk-A-Phone Co. Creating Communication Solutions Installation & Operation Manual For EB-200 Base Station Section Page Getting Started Hardware Installation Programming the Base Station Operation FCC Information Phone Line Specifications Information to the User Talk-A-Phone Co. Limited Warranty 2 3 4 5 6 7 8 9 Talk-A-Phone Co. 7530 North Natchez Avenue Niles, Illinois 60714-3804 Phone: (773) 539-1100 Fax: (773) 539-1241 e-mail: info@talkaphone.com http://www.talkaphone.
PAGE 2
Getting Started I. Getting Started A. Introduction Thank you for your purchase of this Model EB-200 Base Station. This unit is built with an exceptional standard of quality and should provide years of reliable service. This manual will guide you through the installation of this unit and provide comprehensive operating instructions. Please read this instruction manual COMPLETELY before you install this unit.
PAGE 3
Hardware Installation II. Hardware Installation A. Connecting the Base Station Plug the RJ11 male connector from the incoming phone line into the RJ11 connector marked "Line" on the rear of the Base Station. Plug the RJ11 male connector on the phone cable coming from the guard or attendant phone into the RJ11 female connector marked "Phone" on the rear of the Base Station. B.
PAGE 4
Programming the Base Station D. Connecting a Printer Connect a serial printer to the SERIAL port on the Base Station. Make sure the printer has paper and is provided with power. If you are using model EB-P1 Palm Printer, be sure to feed the paper spool through the lower slot and advance the paper. The LED should be lit to indicate that the unit is receiving power. III.
PAGE 5
Operation Programming Commands Setting Serial Printer Baud Rate: Enter *2XXXXY Setting Base Station ID *6XXXXXX Setting The Date *7MMDDYY Setting The Time *8HHMMSSD XXXX = 0300 for 300 baud XXXX = 0600 for 600 baud XXXX = 1200 for 1200 baud (default) XXXX = 2400 for 2400 baud XXXX = anything else, "OOPS" will be displayed. Y = 1 to ignore CTS (clear-to-send from the printer) Y = 0 sets CTS to high (default) Y = anything else, "OOPS" will be displayed.
PAGE 6
FCC Information V. Federal Communications Commission Information This device has been granted a registration number by the Federal Communications Commission (FCC), under part 8 rules and regulations for direct connection to telephone lines. In order to comply with these FCC rules, the following instructions must be carefully read and applicable portions followed completely. These instructions must be provided to the consumer. A. This equipment complies with part 68 of the FCC rules.
PAGE 7
Phone Line Specifications VI. Phone Line Specifications A. MODE I Operation The following criteria must be met by a phone line to insure proper functionality of the FCC approved equipment. All voltages use Tip as ground when measuring. 1. On-Hook voltage must be less than or equal to –36 V (-50 V standard). 2. Off-Hook should be recognized in a maximum time of 300 ms. 3. At an Off-Hook voltage of –15 V, the current that is supplied must be no less than 20 mA and no more than 120 mA. 4.
PAGE 8
Information to the User VII. Information To The User A. Section 15.105 This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 9
Talk-A-Phone Limited Warranty VIII. Talk-A-Phone Co. Limited Warranty Talk-A-Phone Co. warrants Talk-A-Phone equipment against any defects in material and workmanship, under normal use, for a period of twelve (12) months from date of installation, provided that Talk-A-Phone receives a completed "Installation Certification" certifying the date on which the system has been installed. An "Installation Certification" card is enclosed with every unit.